Kernel Doc 中关于ubi的陈述

 

 

Introduction

=============

 

UBIFS file-system stands for UBI File System. UBI stands for "Unsorted

Block Images". UBIFS is a flash file system, which means it is designed

to work with flash devices. It is important to understand, that UBIFS

is completely different to any traditional file-system in Linux, like

Ext2, XFS, JFS, etc. UBIFS represents a separate class of file-systems

which work with MTD devices, not block devices. The other Linux

file-system of this class is JFFS2.

 

To make it more clear, here is a small comparison of MTD devices and

block devices.

 

1 MTD devices represent flash devices and they consist of eraseblocks of

  rather large size, typically about 128KiB. Block devices consist of

  small blocks, typically 512 bytes.

2 MTD devices support 3 main operations - read from some offset within an

  eraseblock, write to some offset within an eraseblock, and erase a whole

  eraseblock. Block  devices support 2 main operations - read a whole

  block and write a whole block.

3 The whole eraseblock has to be erased before it becomes possible to

  re-write its contents. Blocks may be just re-written.

4 Eraseblocks become worn out after some number of erase cycles -

  typically 100K-1G for SLC NAND and NOR flashes, and 1K-10K for MLC

  NAND flashes. Blocks do not have the wear-out property.

5 Eraseblocks may become bad (only on NAND flashes) and software should

  deal with this. Blocks on hard drives typically do not become bad,

  because hardware has mechanisms to substitute bad blocks, at least in

  modern LBA disks.

 

It should be quite obvious why UBIFS is very different to traditional

file-systems.

 

UBIFS works on top of UBI. UBI is a separate software layer which may be

found in drivers/mtd/ubi. UBI is basically a volume management and

wear-leveling layer. It provides so called UBI volumes which is a higher

level abstraction than a MTD device. The programming model of UBI devices

is very similar to MTD devices - they still consist of large eraseblocks,

they have read/write/erase operations, but UBI devices are devoid of

limitations like wear and bad blocks (items 4 and 5 in the above list).

 

In a sense, UBIFS is a next generation of JFFS2 file-system, but it is

very different and incompatible to JFFS2. The following are the main

differences.

 

* JFFS2 works on top of MTD devices, UBIFS depends on UBI and works on

  top of UBI volumes.

* JFFS2 does not have on-media index and has to build it while mounting,

  which requires full media scan. UBIFS maintains the FS indexing

  information on the flash media and does not require full media scan,

  so it mounts many times faster than JFFS2.

* JFFS2 is a write-through file-system, while UBIFS supports write-back,

  which makes UBIFS much faster on writes.

 

Similarly to JFFS2, UBIFS supports on-the-flight compression which makes

it possible to fit quite a lot of data to the flash.

 

Similarly to JFFS2, UBIFS is tolerant of unclean reboots and power-cuts.

It does not need stuff like fsck.ext2. UBIFS automatically replays its

journal and recovers from crashes, ensuring that the on-flash data

structures are consistent.

 

UBIFS scales logarithmically (most of the data structures it uses are

trees), so the mount time and memory consumption do not linearly depend

on the flash size, like in case of JFFS2. This is because UBIFS

maintains the FS index on the flash media. However, UBIFS depends on

UBI, which scales linearly. So overall UBI/UBIFS stack scales linearly.

Nevertheless, UBI/UBIFS scales considerably better than JFFS2.

 

The authors of UBIFS believe, that it is possible to develop UBI2 which

would scale logarithmically as well. UBI2 would support the same API as UBI,

but it would be binary incompatible to UBI. So UBIFS would not need to be

changed to use UBI2

 

 

Mount options

=============

 

(*) == default.

 

bulk_read read more in one go to take advantage of flash

media that read faster sequentially

no_bulk_read (*) do not bulk-read

no_chk_data_crc skip checking of CRCs on data nodes in order to

improve read performance. Use this option only

if the flash media is highly reliable. The effect

of this option is that corruption of the contents

of a file can go unnoticed.

chk_data_crc (*) do not skip checking CRCs on data nodes

compr=none              override default compressor and set it to "none"

compr=lzo               override default compressor and set it to "lzo"

compr=zlib              override default compressor and set it to "zlib"

 

 

Quick usage instructions

========================

 

The UBI volume to mount is specified using "ubiX_Y" or "ubiX:NAME" syntax,

where "X" is UBI device number, "Y" is UBI volume number, and "NAME" is

UBI volume name.

 

Mount volume 0 on UBI device 0 to /mnt/ubifs:

$ mount -t ubifs ubi0_0 /mnt/ubifs

 

Mount "rootfs" volume of UBI device 0 to /mnt/ubifs ("rootfs" is volume

name):

$ mount -t ubifs ubi0:rootfs /mnt/ubifs

 

The following is an example of the kernel boot arguments to attach mtd0

to UBI and mount volume "rootfs":

ubi.mtd=0 root=ubi0:rootfs rootfstype=ubifs

 

 

Module Parameters for Debugging

===============================

 

When UBIFS has been compiled with debugging enabled, there are 3 module

parameters that are available to control aspects of testing and debugging.

The parameters are unsigned integers where each bit controls an option.

The parameters are:

 

debug_msgs Selects which debug messages to display, as follows:

 

Message Type Flag value

 

General messages 1

Journal messages 2

Mount messages 4

Commit messages 8

LEB search messages 16

Budgeting messages 32

Garbage collection messages 64

Tree Node Cache (TNC) messages 128

LEB properties (lprops) messages 256

Input/output messages 512

Log messages 1024

Scan messages 2048

Recovery messages 4096

 

debug_chks Selects extra checks that UBIFS can do while running:

 

Check Flag value

 

General checks 1

Check Tree Node Cache (TNC) 2

Check indexing tree size 4

Check orphan area 8

Check old indexing tree 16

Check LEB properties (lprops) 32

Check leaf nodes and inodes 64

 

debug_tsts Selects a mode of testing, as follows:

 

Test mode Flag value

 

Force in-the-gaps method 2

Failure mode for recovery testing 4

 

For example, set debug_msgs to 5 to display General messages and Mount

messages.

 

 

References

==========

 

UBIFS documentation and FAQ/HOWTO at the MTD web site:

http://www.linux-mtd.infradead.org/doc/ubifs.html

http://www.linux-mtd.infradead.org/faq/ubifs.html