linux编译mmc驱动,Linux mmc+sd 2G驱动
[] [] [prev in thread] []
List:
Subject:
From:
Date:
Message-ID:
[]
Hi Pierre,
I couldn't wait to do this, so here's the updated diff :-)
I've taken your previous comments to heart and I believe that
this can probably just be a single diff, but if you want me to
split it out, just ask.
This adds support for the high-speed modes defined by mmc v4
(assuming the host controller is up to it). On a TI sdhci controller,
it improves read speed from 1.3MBps to 2.3MBps. The TI controller can
only go up to 24MHz, but everything helps. Another person has taken
this basic patch and used it on a Nokia 770 to get a bigger boost
because that controller can run at 48MHZ.
Thanks,
--phil
Signed-off-by: Philip Langdale ---
drivers/mmc/mmc.c | 110 ++++++++++++++++++++++++++++++++++++++++++-
include/linux/mmc/card.h | 8 +++
include/linux/mmc/protocol.h | 16 +++++-
3 files changed, 129 insertions(+), 5 deletions(-)
diff -urN /usr/src/linux-2.6.18/drivers/mmc/mmc.c linux-2.6.18-mmc4/drivers/mmc/mmc.c
--- /usr/src/linux-2.6.18/drivers/mmc/mmc.c2006-09-19 20:42:06.000000000 -0700
+++ linux-2.6.18-mmc4/drivers/mmc/mmc.c2006-10-03 22:14:05.000000000 -0700
@@ -4,6 +4,7 @@
* Copyright (C) 2003-2004 Russell King, All Rights Reserved.
* SD support Copyright (C) 2004 Ian Molton, All Rights Reserved.
* SD support Copyright (C) 2005 Pierre Ossman, All Rights Reserved.
+ * MMCv4 support Copyright (C) 2006 Philip Langdale, All Rights Reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
@@ -427,6 +428,30 @@
}
}
+/* Activate highspeed MMC v4 support. */
+if (card->csd.mmca_vsn == CSD_SPEC_VER_4) {
+struct mmc_command cmd;
+
+ /*
+ * Arg breakdown:
+ * [31:26] Set to 0
+ * [25:24] Access: Write Byte (0x03)
+ * [23:16] Index: HS_TIMING (0xB9)
+ * [15:08] Value: True (0x01)
+ * [07:03] Set to 0
+ * [02:00] Cmd Set: Standard (0x00)
+ */
+cmd.opcode = MMC_SWITCH;
+ cmd.arg = 0x03B90100;
+cmd.flags = MMC_RSP_R1B;
+
+err = mmc_wait_for_cmd(host, &cmd, CMD_RETRIES);
+if (err != MMC_ERR_NONE)
+return err;
+
+mmc_card_set_highspeed(card);
+}
+
mmc_set_ios(host);
return MMC_ERR_NONE;
@@ -953,6 +978,74 @@
}
}
+static void mmc_read_ext_csds(struct mmc_host *host)
+{
+int err;
+struct mmc_card *card;
+
+struct mmc_request mrq;
+struct mmc_command cmd;
+struct mmc_data data;
+
+struct scatterlist sg;
+
+/*
+ * As the ext_csd is so large and mostly unused, we don't store the
+ * raw block in mmc_card.
+ */
+u8 ext_csd[512];
+
+list_for_each_entry(card, &host->cards, node) {
+if (card->state & (MMC_STATE_DEAD|MMC_STATE_PRESENT))
+continue;
+if (mmc_card_sd(card))
+continue;
+if (card->csd.mmca_vsn < CSD_SPEC_VER_4)
+continue;
+
+err = mmc_select_card(host, card);
+if (err != MMC_ERR_NONE) {
+mmc_card_set_dead(card);
+continue;
+}
+
+memset(&cmd, 0, sizeof(struct mmc_command));
+
+cmd.opcode = MMC_SEND_EXT_CSD;
+cmd.arg = 0;
+cmd.flags = MMC_RSP_R1;
+
+memset(&data, 0, sizeof(struct mmc_data));
+
+mmc_set_data_timeout(&data, card, 0);
+
+data.blksz_bits = 9;
+data.blksz = 1 << 9;
+data.blocks = 1;
+data.flags = MMC_DATA_READ;
+data.sg = &sg;
+data.sg_len = 1;
+
+memset(&mrq, 0, sizeof(struct mmc_request));
+
+mrq.cmd = &cmd;
+mrq.data = &data;
+
+sg_init_one(&sg, &ext_csd, 512);
+
+mmc_wait_for_req(host, &mrq);
+
+if (cmd.error != MMC_ERR_NONE || data.error != MMC_ERR_NONE) {
+mmc_card_set_dead(card);
+continue;
+}
+
+card->ext_csd.card_type = ext_csd[196];
+}
+
+mmc_deselect_cards(host);
+}
+
static void mmc_read_scrs(struct mmc_host *host)
{
int err;
@@ -1032,8 +1125,19 @@
unsigned int max_dtr = host->f_max;
list_for_each_entry(card, &host->cards, node)
-if (!mmc_card_dead(card) && max_dtr > card->csd.max_dtr)
-max_dtr = card->csd.max_dtr;
+if (!mmc_card_dead(card)) {
+if (mmc_card_highspeed(card))
+if ((card->ext_csd.card_type & EXT_CSD_CARD_TYPE_52) &&
+ max_dtr > 52000000)
+max_dtr = 52000000;
+else if ((card->ext_csd.card_type & EXT_CSD_CARD_TYPE_26) &&
+ max_dtr > 26000000)
+max_dtr = 26000000;
+else /* mmc v4 spec says this cannot happen */
+BUG_ON(card->ext_csd.card_type == 0);
+else if (max_dtr > card->csd.max_dtr)
+max_dtr = card->csd.max_dtr;
+}
pr_debug("%s: selected %d.%03dMHz transfer rate\n",
mmc_hostname(host),
@@ -1153,6 +1257,8 @@
if (host->mode == MMC_MODE_SD)
mmc_read_scrs(host);
+else
+mmc_read_ext_csds(host);
}
diff -urN /usr/src/linux-2.6.18/include/linux/mmc/card.h \
linux-2.6.18-mmc4/include/linux/mmc/card.h
--- /usr/src/linux-2.6.18/include/linux/mmc/card.h2006-09-19 20:42:06.000000000 \
-0700
+++ linux-2.6.18-mmc4/include/linux/mmc/card.h2006-10-03 22:13:58.000000000 -0700
@@ -39,6 +39,10 @@
write_misalign:1;
};
+struct mmc_ext_csd {
+unsigned charcard_type;
+};
+
struct sd_scr {
unsigned charsda_vsn;
unsigned charbus_widths;
@@ -62,11 +66,13 @@
#define MMC_STATE_BAD(1<<2)/* unrecognised device */
#define MMC_STATE_SDCARD(1<<3)/* is an SD card */
#define MMC_STATE_READONLY(1<<4)/* card is read-only */
+#define MMC_STATE_HIGHSPEED(1<<5)/* card is in mmc4 highspeed mode */
u32raw_cid;/* raw card CID */
u32raw_csd;/* raw card CSD */
u32raw_scr;/* raw card SCR */
struct mmc_cidcid;/* card identification */
struct mmc_csdcsd;/* card specific */
+struct mmc_ext_csdext_csd;/* mmc v4 extended card specific */
struct sd_scrscr;/* extra SD information */
};
@@ -75,12 +81,14 @@
#define mmc_card_bad(c)((c)->state & MMC_STATE_BAD)
#define mmc_card_sd(c)((c)->state & MMC_STATE_SDCARD)
#define mmc_card_readonly(c)((c)->state & MMC_STATE_READONLY)
+#define mmc_card_highspeed(c)((c)->state & MMC_STATE_HIGHSPEED)
#define mmc_card_set_present(c)((c)->state |= MMC_STATE_PRESENT)
#define mmc_card_set_dead(c)((c)->state |= MMC_STATE_DEAD)
#define mmc_card_set_bad(c)((c)->state |= MMC_STATE_BAD)
#define mmc_card_set_sd(c)((c)->state |= MMC_STATE_SDCARD)
#define mmc_card_set_readonly(c) ((c)->state |= MMC_STATE_READONLY)
+#define mmc_card_set_highspeed(c) ((c)->state |= MMC_STATE_HIGHSPEED)
#define mmc_card_name(c)((c)->cid.prod_name)
#define mmc_card_id(c)((c)->dev.bus_id)
diff -urN /usr/src/linux-2.6.18/include/linux/mmc/protocol.h \
linux-2.6.18-mmc4/include/linux/mmc/protocol.h
--- /usr/src/linux-2.6.18/include/linux/mmc/protocol.h2006-09-19 20:42:06.000000000 \
-0700
+++ linux-2.6.18-mmc4/include/linux/mmc/protocol.h2006-10-03 22:14:08.000000000 \
-0700 @@ -25,14 +25,16 @@
#ifndef MMC_MMC_PROTOCOL_H
#define MMC_MMC_PROTOCOL_H
-/* Standard MMC commands (3.1) type argument response */
+/* Standard MMC commands (4.1) type argument response */
/* class 1 */
#defineMMC_GO_IDLE_STATE 0 /* bc */
#define MMC_SEND_OP_COND 1 /* bcr [31:0] OCR R3 */
#define MMC_ALL_SEND_CID 2 /* bcr R2 */
#define MMC_SET_RELATIVE_ADDR 3 /* ac [31:16] RCA R1 */
#define MMC_SET_DSR 4 /* bc [31:16] RCA */
+#define MMC_SWITCH 6 /* ac [31:0] Complex R1b */
#define MMC_SELECT_CARD 7 /* ac [31:16] RCA R1 */
+#define MMC_SEND_EXT_CSD 8 /* adtc R1 */
#define MMC_SEND_CSD 9 /* ac [31:16] RCA R2 */
#define MMC_SEND_CID 10 /* ac [31:16] RCA R2 */
#define MMC_READ_DAT_UNTIL_STOP 11 /* adtc [31:0] dadr R1 */
@@ -229,13 +231,21 @@
#define CSD_STRUCT_VER_1_0 0 /* Valid for system specification 1.0 - 1.2 \
*/ #define CSD_STRUCT_VER_1_1 1 /* Valid for system specification 1.4 - \
2.2 */
-#define CSD_STRUCT_VER_1_2 2 /* Valid for system specification 3.1 \
*/ +#define CSD_STRUCT_VER_1_2 2 /* Valid for system specification 3.1 - \
3.2 - 3.31 - 4.0 - 4.1 */ +#define CSD_STRUCT_EXT_CSD 3 /* Version is \
coded in CSD_STRUCTURE in EXT_CSD */
#define CSD_SPEC_VER_0 0 /* Implements system specification 1.0 - 1.2 \
*/ #define CSD_SPEC_VER_1 1 /* Implements system specification 1.4 */
#define CSD_SPEC_VER_2 2 /* Implements system specification 2.0 - 2.2 \
*/
-#define CSD_SPEC_VER_3 3 /* Implements system specification 3.1 */
+#define CSD_SPEC_VER_3 3 /* Implements system specification 3.1 - 3.2 \
- 3.31 */ +#define CSD_SPEC_VER_4 4 /* Implements system specification \
4.0 - 4.1 */
+/*
+ * EXT_CSD field definitions
+ */
+
+#define EXT_CSD_CARD_TYPE_26(1<<0)/* Card can run at 26MHz */
+#define EXT_CSD_CARD_TYPE_52(1<<1)/* Card can run at 52MHz */
/*
* SD bus widths
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at
Please read the FAQ at