思科路由器交换机密码破解教程

1. 路由器密码的恢复.

 

2600、3600等新系列路由器步骤：

1、启动路由器，60秒内按下ctrl+break键2、rommon>confreg 0x21423、rommon>reset4、router#copy startup-config running-config5、router(config)#no enable secrect  //可以删除密码也可以更改,这里为删除6、router(config)#no enable password7、router(config)#config-register 0x21028、router#copy  running-config  startup9、router#reload

2500系列路由器步骤：

1、启动路由器，60秒内按下ctrl+break键2、>o/r 0x21423、>i其余步骤跟2600、3600一样

2．交换机密码恢复

以2950为例

重启交换机：按MODE键进入到switch:模式 如下

C2950 Boot Loader (C2950-HBOOT-M) Version 12.1(11r)EA1, RELEASE SOFTWARE (fc1)Compiled Mon 22-Jul-02 17:18 by antoninoWS-C2950-24 starting...Base ethernet MAC Address: 00:13:1a:9a:2b:80Xmodem file system is available.

The system has been interrupted prior to initializing theflash filesystem.  The following commands will initializethe flash filesystem, and finish loading the operatingsystem software:

    flash_init    load_helper    boot

switch: flash_initInitializing Flash...flashfs[0]: 4 files, 1 directoriesflashfs[0]: 0 orphaned files, 0 orphaned directoriesflashfs[0]: Total bytes: 7741440flashfs[0]: Bytes used: 3090944flashfs[0]: Bytes available: 4650496flashfs[0]: flashfs fsck took 6 seconds....done initializing flash.Boot Sector Filesystem (bs:) installed, fsid: 3Parameter Block Filesystem (pb:) installed, fsid: 4switch: load_helperswitch: dir

List of filesystems currently registered:

               flash[0]: (read-write)              xmodem[1]: (read-only)                null[2]: (read-write)                  bs[3]: (read-only)

switch: dir flash:Directory of flash:/

2    -rwx  736                      vlan.dat3    -rwx  3086336                  c2950-i6q4l2-mz.121-22.EA2.bin5    -rwx  1558                     config.text／／交换机启动时应用的配置6    -rwx  5                        private-config.text

4650496 bytes available (3090944 bytes used)switch: rename flash:config.text flash:config-old.txt //重命名config.text switch: reset   //重起交换机Are you sure you want to reset the system (y/n)?ySystem resetting...

重起交换机后由于交换机不会再应用配置文件，因为刚才已把配置文件的名字更改。交换机会进入到配置的对话模式。如查

 --- System Configuration Dialog ---
Would you like to enter the initial configuration dialog? [yes/no]: nSwitch#dirDirectory of flash:/
    2  -rwx         736  Mar 01 1993 00:19:14 +00:00  vlan.dat    3  -rwx     3086336  Jan 01 1970 01:12:26 +00:00  c2950-i6q4l2-mz.121-22.EA2.bin    5  -rwx        1558  Mar 01 1993 02:36:44 +00:00  config-old.txt    6  -rwx           5  Mar 01 1993 02:36:44 +00:00  private-config.text
7741440 bytes total (4650496 bytes free)
Switch#copy config-old.txt running-configDestination filename [running-config]?1558 bytes copied in 1.152 secs (1352 bytes/sec)sw#config tEnter configuration commands, one per line.  End with CNTL/Z.sw(config)#line console 0sw(config-line)#no pass cisco ／／清除console口密码sw(config)#no enable secret  ／／清除enable密码sw(config)#no enable password ／／清除enable密码sw#write  //重新保存

以上密码删除成功，很多情况下你可以不删除，就直接更改就OK了。