iperf3 使用

https://baijiahao.baidu.com/s?id=1731514357681464971&wfr=spider&for=pc

sudo mkdir /mnt/shared 
sudo cp ./../cfg.sh /home/zt/Downloads/cfg.sh    
sudo cp crontab  /etc/crontab
sudo service cron reload #/*重新载入配置*/
sudo service cron restart #/*重启服务*/
sudo cp sources.list /etc/apt/sources.list 
sudo apt update
sudo apt install make
#sudo dpkg -i *deb
sudo apt install ethtool
#sudo cp grub /etc/default/grub 
#sudo reboot


#huge
#sudo cp grub /etc/default/grub 
#sudo reboot
#su << EOF
#zt
#EOF
echo 2048  > /sys/kernel/mm/hugepages/hugepages-2048kB/nr_hugepages
echo always > /sys/kernel/mm/transparent_hugepage/enabled


modprobe uio
insmod /mnt/shared/vpp/ubuntu1804/IGB/igb_uio.ko

#grep Huge /proc/meminfo
sudo mkdir -p /mnt/huge
sudo mount -t hugetlbfs  nodev /mnt/huge
mount |tail -1
sudo mount -t hugetlbfs pagesize=2GB /mnt/huge


#enp0s8  eth1 0000:00:0a.0 #查看BDF：ethtool -i eth1
#enp0s9  eth2 0000:00:09.0
#enp0s10 eth3 0000:00:0a.0
#ifconfig enp0s8 90.10.10.100 netmask 255.255.255.0
ifconfig enp0s9 down
ifconfig enp0s10 down

#ifconfig eth1 90.10.40.100 netmask 255.255.255.0
#ifconfig eth2 down
#ifconfig eth3 down

unix {
  nodaemon
  log /var/log/vpp/vpp1.log
  full-coredump
  cli-listen /run/vpp/cli1.sock
  gid vpp
  cli-prompt vpp1#
  ## run vpp in the interactive mode
   interactive

  ## do not use colors in terminal output
  # nocolor

  ## do not display banner
  # nobanner
}

api-trace {
## This stanza controls binary API tracing. Unless there is a very strong reason,
## please leave this feature enabled.
  on
## Additional parameters:
##
## To set the number of binary API trace records in the circular buffer, configure nitems
##
## nitems 
##
## To save the api message table decode tables, configure a filename. Results in /tmp/
## Very handy for understanding api message changes between versions, identifying missing
## plugins, and so forth.
##
## save-api-table 
}

api-segment {
  prefix vpp1
  gid vpp
}

socksvr {
  default
}

# memory {
	## Set the main heap size, default is 1G
	# main-heap-size 2G

	## Set the main heap page size. Default page size is OS default page
	## which is in most cases 4K. if different page size is specified VPP
	## will try to allocate main heap by using specified page size.
	## special keyword 'default-hugepage' will use system default hugepage
	## size
	# main-heap-page-size 1G
#}

cpu {
	## In the VPP there is one main thread and optionally the user can create worker(s)
	## The main thread and worker thread(s) can be pinned to CPU core(s) manually or automatically

	## Manual pinning of thread(s) to CPU core(s)

	## Set logical CPU core where main thread runs, if main core is not set
	## VPP will use core 1 if available
	# main-core 1

	## Set logical CPU core(s) where worker threads are running
	# corelist-workers 2-3,18-19

	## Automatic pinning of thread(s) to CPU core(s)

	## Sets number of CPU core(s) to be skipped (1 ... N-1)
	## Skipped CPU core(s) are not used for pinning main thread and working thread(s).
	## The main thread is automatically pinned to the first available CPU core and worker(s)
	## are pinned to next free CPU core(s) after core assigned to main thread
	# skip-cores 4

	## Specify a number of workers to be created
	## Workers are pinned to N consecutive CPU cores while skipping "skip-cores" CPU core(s)
	## and main thread's CPU core
	# workers 2

	## Set scheduling policy and priority of main and worker threads

	## Scheduling policy options are: other (SCHED_OTHER), batch (SCHED_BATCH)
	## idle (SCHED_IDLE), fifo (SCHED_FIFO), rr (SCHED_RR)
	# scheduler-policy fifo

	## Scheduling priority is used only for "real-time policies (fifo and rr),
	## and has to be in the range of priorities supported for a particular policy
	# scheduler-priority 50
}

# buffers {
	## Increase number of buffers allocated, needed only in scenarios with
	## large number of interfaces and worker threads. Value is per numa node.
	## Default is 16384 (8192 if running unpriviledged)
	# buffers-per-numa 128000

	## Size of buffer data area
	## Default is 2048
	# default data-size 2048

	## Size of the memory pages allocated for buffer data
	## Default will try 'default-hugepage' then 'default'
	## you can also pass a size in K/M/G e.g. '8M'
	# page-size default-hugepage
# }

 dpdk {
	## Change default settings for all interfaces
	# dev default {
		## Number of receive queues, enables RSS
		## Default is 1
		# num-rx-queues 3

		## Number of transmit queues, Default is equal
		## to number of worker threads or 1 if no workers treads
		# num-tx-queues 3

		## Number of descriptors in transmit and receive rings
		## increasing or reducing number can impact performance
		## Default is 1024 for both rx and tx
		# num-rx-desc 512
		# num-tx-desc 512

		## VLAN strip offload mode for interface
		## Default is off
		# vlan-strip-offload on

		## TCP Segment Offload
		## Default is off
		## To enable TSO, 'enable-tcp-udp-checksum' must be set
		# tso on

		## Devargs
                ## device specific init args
                ## Default is NULL
		# devargs safe-mode-support=1,pipeline-mode-support=1

		## rss-queues
		## set valid rss steering queues
		# rss-queues 0,2,5-7
	# }

	## Whitelist specific interface by specifying PCI address
	# dev 0000:02:00.0

	## Blacklist specific device type by specifying PCI vendor:device
        ## Whitelist entries take precedence
	# blacklist 8086:10fb

	## Set interface name
	# dev 0000:02:00.1 {
	#	name eth0
	# }
	# dev 0000:00:09.0{
	#	name GigabitEthernet4/0/2
	# }
	# dev 0000:00:0a.0{
	#	name GigabitEthernet4/0/3
	# }
	 dev 0000:00:0a.0{
		name TenGigabitEthernet3/0/1
	 }
	## Whitelist specific interface by specifying PCI address and in
	## addition specify custom parameters for this interface
	# dev 0000:02:00.1 {
	#	num-rx-queues 2
	# }

	## Change UIO driver used by VPP, Options are: igb_uio, vfio-pci,
	## uio_pci_generic or auto (default)
	# uio-driver vfio-pci

	## Disable multi-segment buffers, improves performance but
	## disables Jumbo MTU support
	# no-multi-seg

	## Change hugepages allocation per-socket, needed only if there is need for
	## larger number of mbufs. Default is 256M on each detected CPU socket
	# socket-mem 2048,2048

	## Disables UDP / TCP TX checksum offload. Typically needed for use
	## faster vector PMDs (together with no-multi-seg)
	# no-tx-checksum-offload

	## Enable UDP / TCP TX checksum offload
	## This is the reversed option of 'no-tx-checksum-offload'
	# enable-tcp-udp-checksum
 }

## node variant defaults
#node {

## specify the preferred default variant
#	default	{ variant avx512 }

## specify the preferred variant, for a given node
#	ip4-rewrite { variant avx2 }

#}


 plugins {
	## Adjusting the plugin path depending on where the VPP plugins are
	#	path /ws/vpp/build-root/install-vpp-native/vpp/lib/vpp_plugins

	## Disable all plugins by default and then selectively enable specific plugins
	# plugin default { disable }
	 plugin dpdk_plugin.so { enable }
	 plugin oddbuf_plugin.so { enable }
	# plugin acl_plugin.so { enable }

	## Enable all plugins by default and then selectively disable specific plugins
	# plugin dpdk_plugin.so { disable }
	# plugin acl_plugin.so { disable }
 }

## Statistics Segment
# statseg {
    # socket-name , name of the stats segment socket
    #     defaults to /run/vpp/stats.sock
    # size [KMG], size of the stats segment, defaults to 32mb
    # page-size , page size, ie. 2m, defaults to 4k
    # per-node-counters on | off, defaults to none
    # update-interval , sets the segment scrape / update interval
# }

## L2 FIB
# l2fib {
    ## l2fib hash table size.
    #  table-size 512M

    ## l2fib hash table number of buckets. Must be power of 2.
    #  num-buckets 524288
# }

## ipsec
# {
   # ip4 {
   ## ipsec for ipv4 tunnel lookup hash number of buckets.
   #  num-buckets 524288
   # }
   # ip6 {
   ## ipsec for ipv6 tunnel lookup hash number of buckets.
   #  num-buckets 524288
   # }
# }

# logging {
   ## set default logging level for logging buffer
   ## logging levels: emerg, alert,crit, error, warn, notice, info, debug, disabled
   # default-log-level debug
   ## set default logging level for syslog or stderr output
   # default-syslog-log-level info
   ## Set per-class configuration
   # class dpdk/cryptodev { rate-limit 100 level debug syslog-level error }
# }