- 常用命令
- console配置
- 接口IP配置
- 认证模式、用户权限配置
- system-view sys # 进入系统视图
- quit q # 退出当前视图
- return # 返回用户视图
- sysname #重命名
- display version #查看当前配置
The device is running!
system-view
Enter system view, return user view with Ctrl+Z.
[Huawei]q
sys
Enter system view, return user view with Ctrl+Z.
[Huawei]quit
sys
Enter system view, return user view with Ctrl+Z.
[Huawei]ospf 10
[Huawei-ospf-10]area 0
[Huawei-ospf-10-area-0.0.0.0]return
sysname AR1
^
Error: Unrecognized command found at '^' position.
sys
Enter system view, return user view with Ctrl+Z.
[Huawei]sysname AR1
[AR1]display int
[AR1]display interface
GigabitEthernet0/0/0 current state : UP
Line protocol current state : DOWN
Description:HUAWEI, AR Series, GigabitEthernet0/0/0 Interface
Route Port,The Maximum Transmit Unit is 1500
Internet protocol processing : disabled
IP Sending Frames' Format is PKTFMT_ETHNT_2, Hardware address is 00e0-fc82-7ac7
Last physical up time : 2022-09-17 20:06:56 UTC-08:00
Last physical down time : 2022-09-17 20:06:48 UTC-08:00
Current system time: 2022-09-17 20:11:38-08:00
Port Mode: FORCE COPPER
Speed : 1000, Loopback: NONE
Duplex: FULL, Negotiation: ENABLE
Mdi : AUTO
Last 300 seconds input rate 0 bits/sec, 0 packets/sec
Last 300 seconds output rate 0 bits/sec, 0 packets/sec
Input peak rate 0 bits/sec,Record time: -
Output peak rate 0 bits/sec,Record time: -
Input: 0 packets, 0 bytes
Unicast: 0, Multicast: 0
Broadcast: 0, Jumbo: 0
Discard: 0, Total Error: 0
CRC: 0, Giants: 0
Jabbers: 0, Throttles: 0
Runts: 0, Symbols: 0
Ignoreds: 0, Frames: 0
Output: 0 packets, 0 bytes
Unicast: 0, Multicast: 0
Broadcast: 0, Jumbo: 0
Discard: 0, Total Error: 0
Collisions: 0, ExcessiveCollisions: 0
Late Collisions: 0, Deferreds: 0
Input bandwidth utilization threshold : 100.00%
Output bandwidth utilization threshold: 100.00%
Input bandwidth utilization : 0%
Output bandwidth utilization : 0%
GigabitEthernet0/0/1 current state : DOWN
Line protocol current state : DOWN
Description:HUAWEI, AR Series, GigabitEthernet0/0/1 Interface
Route Port,The Maximum Transmit Unit is 1500
Internet protocol processing : disabled
IP Sending Frames' Format is PKTFMT_ETHNT_2, Hardware address is 00e0-fc82-7ac8
Last physical up time : -
Last physical down time : 2022-09-17 20:06:48 UTC-08:00
Current system time: 2022-09-17 20:11:59-08:00
Port Mode: COMMON COPPER
Speed : 1000, Loopback: NONE
Duplex: FULL, Negotiation: ENABLE
Mdi : AUTO
Last 300 seconds input rate 0 bits/sec, 0 packets/sec
Last 300 seconds output rate 0 bits/sec, 0 packets/sec
Input peak rate 0 bits/sec,Record time: -
Output peak rate 0 bits/sec,Record time: -
Input: 0 packets, 0 bytes
Unicast: 0, Multicast: 0
Broadcast: 0, Jumbo: 0
Discard: 0, Total Error: 0
CRC: 0, Giants: 0
Jabbers: 0, Throttles: 0
Runts: 0, Symbols: 0
Ignoreds: 0, Frames: 0
Output: 0 packets, 0 bytes
Unicast: 0, Multicast: 0
Broadcast: 0, Jumbo: 0
Discard: 0, Total Error: 0
Collisions: 0, ExcessiveCollisions: 0
[AR1]fidplsy history
^
Error: Unrecognized command found at '^' position.
[AR1]display history-co
[AR1]display history-command
fidplsy history
display interface
sysname AR1
sys
return
area 0
ospf 10
quit
q
system-view
[AR1]interface Gi
[AR1]interface GigabitEthernet 0/0/0
[AR1-GigabitEthernet0/0/0]ip address 10.1.1.1 255.255.255.0
Sep 17 2022 20:14:15-08:00 AR1 %%01IFNET/4/LINK_STATE(l)[0]:The line protocol IP
on the interface GigabitEthernet0/0/0 has entered the UP state.
[AR1-GigabitEthernet0/0/0]dis th
[V200R003C00]
#
interface GigabitEthernet0/0/0
ip address 10.1.1.1 255.255.255.0
#
return
[AR1-GigabitEthernet0/0/0]q
[AR1]user-interface console 0
[AR1-ui-console0]authentication-mode password
Please configure the login password (maximum length 16):admin
[AR1-ui-console0]user privilege level 15
[AR1-ui-console0]q
[AR1]aaa
[AR1-aaa]local-user admin password cipher admin
[AR1-aaa]local-user admin privilege level 15
[AR1-aaa]local-user admin service-type telnet
[AR1-aaa]q
[AR1]telnet server enable
Error: TELNET server has been enabled
[AR1]display telnet server status
TELNET IPV4 server :Enable
TELNET IPV6 server :Enable
TELNET server port :23
[AR1]user-interface vty 0 4
[AR1-ui-vty0-4]protocol inbound telnet
[AR1-ui-vty0-4]authentication-mode aaa
[AR1-ui-vty0-4]user privilege level 15
[AR1-ui-vty0-4]return
sys
Enter system view, return user view with Ctrl+Z.
[AR1]user-interface console 0
[AR1-ui-console0]idle-timeout 0 0
[AR1-ui-console0]q
[AR1]display version
Huawei Versatile Routing Platform Software
VRP (R) software, Version 5.130 (AR2200 V200R003C00)
Copyright (C) 2011-2012 HUAWEI TECH CO., LTD
Huawei AR2220 Router uptime is 0 week, 0 day, 0 hour, 31 minutes
BKP 0 version information:
1. PCB Version : AR01BAK2A VER.NC
2. If Supporting PoE : No
3. Board Type : AR2220
4. MPU Slot Quantity : 1
5. LPU Slot Quantity : 6
MPU 0(Master) : uptime is 0 week, 0 day, 0 hour, 31 minutes
MPU version information :
1. PCB Version : AR01SRU2A VER.A
2. MAB Version : 0
3. Board Type : AR2220
4. BootROM Version : 0
The device is running!
sys
Enter system view, return user view with Ctrl+Z.
[Huawei]sysname AR2
[AR2]user-interface console 0
[AR2-ui-console0]idle-timeout 0 0
[AR2-ui-console0]q
[AR2]interface G
[AR2]interface GigabitEthernet 0/0/0
[AR2-GigabitEthernet0/0/0]ip addr 10.1.1.2 24
Sep 17 2022 20:23:39-08:00 AR2 %%01IFNET/4/LINK_STATE(l)[0]:The line protocol IP
on the interface GigabitEthernet0/0/0 has entered the UP state.
[AR2-GigabitEthernet0/0/0]dis th
[V200R003C00]
#
interface GigabitEthernet0/0/0
ip address 10.1.1.2 255.255.255.0
#
return
[AR2-GigabitEthernet0/0/0]dis cu
[V200R003C00]
#
sysname AR2
#
snmp-agent local-engineid 800007DB03000000000000
snmp-agent
#
clock timezone China-Standard-Time minus 08:00:00
#
portal local-server load portalpage.zip
#
drop illegal-mac alarm
#
set cpu-usage threshold 80 restore 75
#
aaa
authentication-scheme default
authorization-scheme default
accounting-scheme default
domain default
domain default_admin
local-user admin password cipher %$%$K8m.Nt84DZ}e#<0`8bmE3Uw}%$%$
local-user admin service-type http
#
[AR2-GigabitEthernet0/0/0]q
[AR2]display telnet server status
TELNET IPV4 server :Enable
TELNET IPV6 server :Enable
TELNET server port :23
[AR2]telnet 10.1.1.1
^
Error: Unrecognized command found at '^' position.
[AR2]ping 10.1.1.1
PING 10.1.1.1: 56 data bytes, press CTRL_C to break
Reply from 10.1.1.1: bytes=56 Sequence=1 ttl=255 time=90 ms
Reply from 10.1.1.1: bytes=56 Sequence=2 ttl=255 time=20 ms
Reply from 10.1.1.1: bytes=56 Sequence=3 ttl=255 time=20 ms
Reply from 10.1.1.1: bytes=56 Sequence=4 ttl=255 time=20 ms
Reply from 10.1.1.1: bytes=56 Sequence=5 ttl=255 time=30 ms
--- 10.1.1.1 ping statistics ---
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 20/36/90 ms
[AR2]telnet 10.1.1.1
^
Error: Unrecognized command found at '^' position.
[AR2]q
telnet 10.1.1.1
Press CTRL_] to quit telnet mode
Trying 10.1.1.1 ...
Connected to 10.1.1.1 ...
Login authentication
Username:admin
Password:
sys
Enter system view, return user view with Ctrl+Z.
[AR1]display users
User-Intf Delay Type Network Address AuthenStatus AuthorcmdFlag
0 CON 0 00:04:38 pass
Username : Unspecified
+ 129 VTY 0 00:00:00 TEL 10.1.1.2 pass
Username : admin
[AR1]
