GME12864-12
1、start()开始
2、slave address 存积地址:011110 xx
写入:b 0111 1000 (0x78)(R / W位置为0时,表示写入)
3、ACK
4、cotrol byte:(Co) (D / C)000000
(Co置为0时,接下来传输的信息包含数据字节data byte)
(D / C位置为0时,表示为命令;为 1 时,表示为数据)
0000 0000 写入命令
0100 0000 写入数据
5、ACK
6、写入指令/数据
7、ACK
8、STOP
//写入命令
void Oled_Write_Cmd(char dataCmd)
{
ICC_Start(); // 1、start()开始
IIC_Send_Byte(0x78); // 2、slave address 存积地址:011110 xx
// 写入:b 0111 1000(0x78)(R/W位置为0时,表示写入)
ICC_ACK(); // 3、ACK
IIC_Send_Byte(0x00); // 4、cotrol byte:(Co) (D/C)000000
//(Co置为0时,接下来传输的信息包含数据字节data byte)
//(D / C位置为0时,表示为命令;为 1 时,表示为数据)
// 0000 0000 写入命令
// 0100 0000 写入数据
ICC_ACK(); // 5、ACK
IIC_Send_Byte(dataCmd); // 6、写入指令/数据
ICC_ACK(); // 7、ACK
ICC_Stop(); // 8、STOP
}
//写入数据
void Oled_Write_Data(char dataData)
{
ICC_Start(); // 1、start()开始
IIC_Send_Byte(0x78); // 2、slave address 存积地址:011110 xx
// 写入:b 0111 1000(0x78)(R/W位置为0时,表示写入)
ICC_ACK(); // 3、ACK
IIC_Send_Byte(0x40); // 4、cotrol byte:(Co) (D/C)000000
//(Co置为0时,接下来传输的信息包含数据字节data byte)
//(D / C位置为0时,表示为命令;为 1 时,表示为数据)
// 0000 0000 写入命令
// 0100 0000 写入数据
ICC_ACK(); // 5、ACK
IIC_Send_Byte(dataData);// 6、写入指令/数据
ICC_ACK(); // 7、ACK
ICC_Stop(); // 8、STOP
}
VDD = 1.65V——3.3V
VCC = 7V —— 15V
128x64个点阵组成:
64=8Page*8bit
自动右移
横向:SEG0——SEG127
竖向:Page0——Page7
页地址模式:
1、发送cmd:0x20
2、发送cmd:0x02;(默认为页模式)
水平地址模式:
垂直地址模式:
配置页地址模式:
Oled_Write_Cmd(0x20);
Oled_Write_Cmd(0x02);
配置显示地址:
Oled_Write_Cmd(0xB0);//配置page1-8
Oled_Write_Cmd(0x00);//列地址,从头开始
Oled_Write_Cmd(0x10);
主函数:
1、OLED初始化
2、选择一个位置
2.1、确认为页面寻址模式
Oled_Write_Cmd(0x20);
Oled_Write_Cmd(0x02);
2.2、选择PAGE0
Oled_Write_Cmd(0xB0);//1011 0000(0xB0)配置page1-8.
3、显示一个点
#include "reg52.h"
#include "intrins.h"
sbit SCL = P0^1;
sbit SDA = P0^3;
void ICC_Start()
{
SDA = 1;
SCL = 1;
_nop_(); //一个nop用时5us
SDA = 0;
_nop_();
}
void ICC_Stop()
{
SDA = 0;
SCL = 1;
_nop_();
SDA = 1;
_nop_();
}
char ICC_ACK()
{
char flag;
SDA = 1; //在时钟脉冲9期间释放
_nop_();
SCL = 1;
_nop_();
flag = SDA;
_nop_();
SCL = 0;
_nop_();
return flag;
}
void IIC_Send_Byte(char dataSend)
{
int i;
for(i = 0;i < 8;i++){
SCL = 0; //SCL低电平,让SDA做好数据准备
SDA = dataSend & 0x80; //与上1000 0000 获得dataSend的最高位,给SDA
_nop_(); //发送数据建立的时间
SCL = 1; //SCL高电平,开始发送数据
_nop_(); //发送数据需要时间
SCL= 0; //发送完毕,SCL拉回低电平
_nop_();
dataSend = dataSend << 1;
}
}
//写入命令
void Oled_Write_Cmd(char dataCmd)
{
ICC_Start(); // 1、start()开始
IIC_Send_Byte(0x78); // 2、slave address 存积地址:011110 xx
// 写入:b 0111 1000(0x78)(R/W位置为0时,表示写入)
ICC_ACK(); // 3、ACK
IIC_Send_Byte(0x00); // 4、cotrol byte:(Co) (D/C)000000
//(Co置为0时,接下来传输的信息包含数据字节data byte)
//(D / C位置为0时,表示为命令;为 1 时,表示为数据)
// 0000 0000 写入命令
// 0100 0000 写入数据
ICC_ACK(); // 5、ACK
IIC_Send_Byte(dataCmd); // 6、写入指令/数据
ICC_ACK(); // 7、ACK
ICC_Stop(); // 8、STOP
}
//写入数据
void Oled_Write_Data(char dataData)
{
ICC_Start(); // 1、start()开始
IIC_Send_Byte(0x78); // 2、slave address 存积地址:011110 xx
// 写入:b 0111 1000(0x78)(R/W位置为0时,表示写入)
ICC_ACK(); // 3、ACK
IIC_Send_Byte(0x40); // 4、cotrol byte:(Co) (D/C)000000
//(Co置为0时,接下来传输的信息包含数据字节data byte)
//(D / C位置为0时,表示为命令;为 1 时,表示为数据)
// 0000 0000 写入命令
// 0100 0000 写入数据
ICC_ACK(); // 5、ACK
IIC_Send_Byte(dataData);// 6、写入指令/数据
ICC_ACK(); // 7、ACK
ICC_Stop(); // 8、STOP
}
void Oled_Init()
{
Oled_Write_Cmd(0xAE);//--display off
Oled_Write_Cmd(0x00);//---set low column address
Oled_Write_Cmd(0x10);//---set high column address
Oled_Write_Cmd(0x40);//--set start line address
Oled_Write_Cmd(0xB0);//--set page address
Oled_Write_Cmd(0x81); // contract control
Oled_Write_Cmd(0xFF);//--128
Oled_Write_Cmd(0xA1);//set segment remap
Oled_Write_Cmd(0xA6);//--normal / reverse
Oled_Write_Cmd(0xA8);//--set multiplex ratio(1 to 64)
Oled_Write_Cmd(0x3F);//--1/32 duty
Oled_Write_Cmd(0xC8);//Com scan direction
Oled_Write_Cmd(0xD3);//-set display offset
Oled_Write_Cmd(0x00);//
Oled_Write_Cmd(0xD5);//set osc division
Oled_Write_Cmd(0x80);//
Oled_Write_Cmd(0xD8);//set area color mode off
Oled_Write_Cmd(0x05);//
Oled_Write_Cmd(0xD9);//Set Pre-Charge Period
Oled_Write_Cmd(0xF1);//
Oled_Write_Cmd(0xDA);//set com pin configuartion
Oled_Write_Cmd(0x12);//
Oled_Write_Cmd(0xDB);//set Vcomh
Oled_Write_Cmd(0x30);//
Oled_Write_Cmd(0x8D);//set charge pump enable
Oled_Write_Cmd(0x14);//
Oled_Write_Cmd(0xAF);//--turn on oled panel
}
void main()
{
Oled_Init(); //OLED初始化
Oled_Write_Cmd(0x20); //选择一个位置,确认为页面寻址模式
Oled_Write_Cmd(0x02);
Oled_Write_Cmd(0xB0); //1011 0000(0xB0)配置page1-8.
//显示一个点
while(1);
}
选择列地址显示
主函数:
1、OLED初始化
2、选择一个位置
2.1、确认为页面寻址模式
Oled_Write_Cmd(0x20);
Oled_Write_Cmd(0x02);
2.2、选择PAGE0
Oled_Write_Cmd(0xB0);//1011 0000(0xB0)配置page1-8.
Oled_Write_Cmd(0x00);//列地址,从头开始
Oled_Write_Cmd(0x10);
3、显示屏写入数据
用点阵液晶取模工具取模
要勾选纵向取模,文字倒序
显示字符A:
#include "reg52.h"
#include "intrins.h"
sbit SCL = P0^1;
sbit SDA = P0^3;
void ICC_Start()
{
SCL = 0; //防止雪花屏
SDA = 1;
SCL = 1;
_nop_(); //一个nop用时5us
SDA = 0;
_nop_();
}
void ICC_Stop()
{
SCL = 0; //防止雪花屏
SDA = 0;
SCL = 1;
_nop_();
SDA = 1;
_nop_();
}
char ICC_ACK()
{
char flag;
SDA = 1; //在时钟脉冲9期间释放
_nop_();
SCL = 1;
_nop_();
flag = SDA;
_nop_();
SCL = 0;
_nop_();
return flag;
}
void IIC_Send_Byte(char dataSend)
{
int i;
for(i = 0;i < 8;i++){
SCL = 0; //SCL低电平,让SDA做好数据准备
SDA = dataSend & 0x80; //与上1000 0000 获得dataSend的最高位,给SDA
_nop_(); //发送数据建立的时间
SCL = 1; //SCL高电平,开始发送数据
_nop_(); //发送数据需要时间
SCL= 0; //发送完毕,SCL拉回低电平
_nop_();
dataSend = dataSend << 1;
}
}
//写入命令
void Oled_Write_Cmd(char dataCmd)
{
ICC_Start(); // 1、start()开始
IIC_Send_Byte(0x78); // 2、slave address 存积地址:011110 xx
// 写入:b 0111 1000(0x78)(R/W位置为0时,表示写入)
ICC_ACK(); // 3、ACK
IIC_Send_Byte(0x00); // 4、cotrol byte:(Co) (D/C)000000
//(Co置为0时,接下来传输的信息包含数据字节data byte)
//(D / C位置为0时,表示为命令;为 1 时,表示为数据)
// 0000 0000 写入命令
// 0100 0000 写入数据
ICC_ACK(); // 5、ACK
IIC_Send_Byte(dataCmd); // 6、写入指令/数据
ICC_ACK(); // 7、ACK
ICC_Stop(); // 8、STOP
}
//写入数据
void Oled_Write_Data(char dataData)
{
ICC_Start(); // 1、start()开始
IIC_Send_Byte(0x78); // 2、slave address 存积地址:011110 xx
// 写入:b 0111 1000(0x78)(R/W位置为0时,表示写入)
ICC_ACK(); // 3、ACK
IIC_Send_Byte(0x40); // 4、cotrol byte:(Co) (D/C)000000
//(Co置为0时,接下来传输的信息包含数据字节data byte)
//(D / C位置为0时,表示为命令;为 1 时,表示为数据)
// 0000 0000 写入命令
// 0100 0000 写入数据
ICC_ACK(); // 5、ACK
IIC_Send_Byte(dataData);// 6、写入指令/数据
ICC_ACK(); // 7、ACK
ICC_Stop(); // 8、STOP
}
void Oled_Init(void)
{
Oled_Write_Cmd(0xAE);//--display off
Oled_Write_Cmd(0x00);//---set low column address
Oled_Write_Cmd(0x10);//---set high column address
Oled_Write_Cmd(0x40);//--set start line address
Oled_Write_Cmd(0xB0);//--set page address
Oled_Write_Cmd(0x81); // contract control
Oled_Write_Cmd(0xFF);//--128
Oled_Write_Cmd(0xA1);//set segment remap
Oled_Write_Cmd(0xA6);//--normal / reverse
Oled_Write_Cmd(0xA8);//--set multiplex ratio(1 to 64)
Oled_Write_Cmd(0x3F);//--1/32 duty
Oled_Write_Cmd(0xC8);//Com scan direction
Oled_Write_Cmd(0xD3);//-set display offset
Oled_Write_Cmd(0x00);//
Oled_Write_Cmd(0xD5);//set osc division
Oled_Write_Cmd(0x80);//
Oled_Write_Cmd(0xD8);//set area color mode off
Oled_Write_Cmd(0x05);//
Oled_Write_Cmd(0xD9);//Set Pre-Charge Period
Oled_Write_Cmd(0xF1);//
Oled_Write_Cmd(0xDA);//set com pin configuartion
Oled_Write_Cmd(0x12);//
Oled_Write_Cmd(0xDB);//set Vcomh
Oled_Write_Cmd(0x30);//
Oled_Write_Cmd(0x8D);//set charge pump enable
Oled_Write_Cmd(0x14);//
Oled_Write_Cmd(0xAF);//--turn on oled panel
}
//清屏
void Oled_Clear()
{
int i,j;
//unsigned char i,j; char范围-128——127,定义char类型会产生越界
for(i = 0;i < 8;i++){
Oled_Write_Cmd(0xB0 + i); //Page0——Page7
Oled_Write_Cmd(0x00); //每个Page从0开始
Oled_Write_Cmd(0x10);
for(j = 0;j < 128;j++){ //0——127列,依次写入0,每写入数据列地址自动偏移。
Oled_Write_Data(0);
}
}
}
/*-- 文字: A --*/
/*-- 宋体12; 此字体下对应的点阵为:宽x高=8x16 (一个Page为8位)--*/
char A1[8] = {0x00,0x00,0xC0,0x38,0xE0,0x00,0x00,0x00};
char A2[8] = {0x20,0x3C,0x23,0x02,0x02,0x27,0x38,0x20};
void main()
{
int i;
Oled_Init(); //OLED初始化
Oled_Write_Cmd(0x20); //选择一个位置,确认为页面寻址模式
Oled_Write_Cmd(0x02);
Oled_Clear(); //清屏
Oled_Write_Cmd(0xB0); //1011 0000(0xB0)配置page1-8.
//显示一个点
Oled_Write_Cmd(0x00); //列地址,从头开始
Oled_Write_Cmd(0x10);
for(i = 0;i < 8;i++){
Oled_Write_Data(A1[i]);
}
Oled_Write_Cmd(0xB1);
Oled_Write_Cmd(0x00);
Oled_Write_Cmd(0x10);
for(i = 0;i < 8;i++){
Oled_Write_Data(A2[i]);
}
while(1);
}
各数据类型大小和取值范围:
https://blog.csdn.net/weixin_42856843/article/details/81989737
大小:128x64像素
保存模式:bmp模式
位图(Bitmap)模式:它没有进行数据压缩,其内部存储的色彩信息(灰度图,RGB 或 ARGB)直接以二进制的形式暴露在外,也十分方便借助计算机软件进行简单或深入的分析。
#include "reg52.h"
#include "intrins.h"
sbit SCL = P0^1;
sbit SDA = P0^3;
void ICC_Start()
{
SCL = 0; //防止雪花屏
SDA = 1;
SCL = 1;
_nop_(); //一个nop用时5us
SDA = 0;
_nop_();
}
void ICC_Stop()
{
SCL = 0; //防止雪花屏
SDA = 0;
SCL = 1;
_nop_();
SDA = 1;
_nop_();
}
char ICC_ACK()
{
char flag;
SDA = 1; //在时钟脉冲9期间释放
_nop_();
SCL = 1;
_nop_();
flag = SDA;
_nop_();
SCL = 0;
_nop_();
return flag;
}
void IIC_Send_Byte(char dataSend)
{
int i;
for(i = 0;i < 8;i++){
SCL = 0; //SCL低电平,让SDA做好数据准备
SDA = dataSend & 0x80; //与上1000 0000 获得dataSend的最高位,给SDA
_nop_(); //发送数据建立的时间
SCL = 1; //SCL高电平,开始发送数据
_nop_(); //发送数据需要时间
SCL= 0; //发送完毕,SCL拉回低电平
_nop_();
dataSend = dataSend << 1;
}
}
//写入命令
void Oled_Write_Cmd(char dataCmd)
{
ICC_Start(); // 1、start()开始
IIC_Send_Byte(0x78); // 2、slave address 存积地址:011110 xx
// 写入:b 0111 1000(0x78)(R/W位置为0时,表示写入)
ICC_ACK(); // 3、ACK
IIC_Send_Byte(0x00); // 4、cotrol byte:(Co) (D/C)000000
//(Co置为0时,接下来传输的信息包含数据字节data byte)
//(D / C位置为0时,表示为命令;为 1 时,表示为数据)
// 0000 0000 写入命令
// 0100 0000 写入数据
ICC_ACK(); // 5、ACK
IIC_Send_Byte(dataCmd); // 6、写入指令/数据
ICC_ACK(); // 7、ACK
ICC_Stop(); // 8、STOP
}
//写入数据
void Oled_Write_Data(char dataData)
{
ICC_Start(); // 1、start()开始
IIC_Send_Byte(0x78); // 2、slave address 存积地址:011110 xx
// 写入:b 0111 1000(0x78)(R/W位置为0时,表示写入)
ICC_ACK(); // 3、ACK
IIC_Send_Byte(0x40); // 4、cotrol byte:(Co) (D/C)000000
//(Co置为0时,接下来传输的信息包含数据字节data byte)
//(D / C位置为0时,表示为命令;为 1 时,表示为数据)
// 0000 0000 写入命令
// 0100 0000 写入数据
ICC_ACK(); // 5、ACK
IIC_Send_Byte(dataData);// 6、写入指令/数据
ICC_ACK(); // 7、ACK
ICC_Stop(); // 8、STOP
}
void Oled_Init(void)
{
Oled_Write_Cmd(0xAE);//--display off
Oled_Write_Cmd(0x00);//---set low column address
Oled_Write_Cmd(0x10);//---set high column address
Oled_Write_Cmd(0x40);//--set start line address
Oled_Write_Cmd(0xB0);//--set page address
Oled_Write_Cmd(0x81); // contract control
Oled_Write_Cmd(0xFF);//--128
Oled_Write_Cmd(0xA1);//set segment remap
Oled_Write_Cmd(0xA6);//--normal / reverse
Oled_Write_Cmd(0xA8);//--set multiplex ratio(1 to 64)
Oled_Write_Cmd(0x3F);//--1/32 duty
Oled_Write_Cmd(0xC8);//Com scan direction
Oled_Write_Cmd(0xD3);//-set display offset
Oled_Write_Cmd(0x00);//
Oled_Write_Cmd(0xD5);//set osc division
Oled_Write_Cmd(0x80);//
Oled_Write_Cmd(0xD8);//set area color mode off
Oled_Write_Cmd(0x05);//
Oled_Write_Cmd(0xD9);//Set Pre-Charge Period
Oled_Write_Cmd(0xF1);//
Oled_Write_Cmd(0xDA);//set com pin configuartion
Oled_Write_Cmd(0x12);//
Oled_Write_Cmd(0xDB);//set Vcomh
Oled_Write_Cmd(0x30);//
Oled_Write_Cmd(0x8D);//set charge pump enable
Oled_Write_Cmd(0x14);//
Oled_Write_Cmd(0xAF);//--turn on oled panel
}
//清屏
void Oled_Clear()
{
int i,j;
//unsigned char i,j; char范围-128——127,定义char类型会产生越界
for(i = 0;i < 8;i++){
Oled_Write_Cmd(0xB0 + i); //Page0——Page7
Oled_Write_Cmd(0x00); //每个Page从0开始
Oled_Write_Cmd(0x10);
for(j = 0;j < 128;j++){ //0——127列,依次写入0,每写入数据列地址自动偏移。
Oled_Write_Data(0);
}
}
}
code unsigned char bmpImager[] = {
/*-- 调入了一幅图像:12864演示图片.bmp --*/
/*-- 宽度x高度=128x64 (有128x8x8个数据)--*/
0x00,0x00,0x80,0xC0,0xE0,0xF0,0xF0,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xF0,0xF0,
0xF0,0xE0,0xE0,0x60,0x70,0x70,0x30,0x30,0x38,0x18,0x18,0x18,0x18,0x18,0x18,0x1C,
0x0C,0x1C,0x1C,0x1C,0x18,0x18,0x18,0x18,0x18,0x30,0x30,0x30,0x60,0x60,0xE0,0xE0,
0xE0,0xF0,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xF0,0xF0,0xE0,0xC0,0x80,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x3E,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0x7F,0x1F,0x1F,0x07,0x07,0x03,
0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x01,0x01,0x03,0x07,0x0F,0x1F,0x3F,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0x7F,
0x7F,0x00,0x00,0x00,0x00,0x00,0xF0,0xF0,0x70,0x30,0x30,0x30,0xF0,0xE0,0x00,0x00,
0x40,0xE0,0x70,0x30,0x30,0x30,0x70,0xF0,0xE0,0x00,0x00,0x00,0xF0,0xF0,0x70,0x30,
0x30,0x70,0xF0,0xE0,0x00,0x00,0xC0,0xE0,0x70,0x30,0x30,0x30,0x30,0x74,0xFF,0xFF,
0x00,0x00,0x00,0xE0,0xF0,0x30,0x30,0x30,0x70,0xF0,0xE0,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x03,0x07,0x0F,0x1F,0xFF,0xFF,0x0F,0x01,0x00,0x00,0x00,0x80,0xE0,0xF0,
0xF8,0xF8,0xFC,0xFC,0x7E,0x7E,0x7E,0xFE,0xFC,0xF8,0x60,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x20,0xF8,0xFC,0xFC,0xFE,0x7E,0xFE,0xFC,0xF8,
0xF8,0xF0,0xE0,0x80,0x00,0x00,0x00,0x01,0x0F,0xFF,0xFF,0x1F,0x0F,0x07,0x03,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0xFF,0x60,0x60,0xE0,0x60,0x7F,0x3F,0x02,0x00,
0x38,0x7D,0xFE,0x66,0xE6,0x66,0x76,0x7F,0x7F,0x00,0x00,0x00,0x7F,0x7F,0x00,0x00,
0x00,0x00,0x7F,0x7F,0x00,0x00,0x1F,0x3F,0x7A,0x60,0xE0,0xE0,0x60,0x78,0x7F,0x7F,
0x00,0x00,0x38,0x7D,0x7F,0xE6,0x46,0x66,0x76,0x7F,0x7F,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x3F,0xFF,0xE0,0x00,0x00,0x00,0x3E,0xFF,0xFF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0x7F,0x1F,0x03,0x00,0x00,0x00,0x60,0xF0,0xF8,
0xF8,0xF8,0xF0,0xF0,0x70,0x00,0x00,0x00,0x07,0x3F,0x7F,0xFF,0xFF,0xFF,0xFF,0xFF,
0xFF,0xFF,0xFF,0xFF,0x7F,0x00,0x00,0x80,0xE0,0xFF,0x3F,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x07,0x07,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x03,0x0F,0x1C,0x38,0x60,0xE0,0xC1,0x81,
0x83,0x03,0x03,0x01,0x01,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x03,0x03,0x83,
0x83,0x83,0xC1,0xE0,0x70,0x38,0x1C,0x0F,0x03,0x80,0x80,0xA0,0xB0,0xB8,0xFC,0xF7,
0xF7,0x92,0x94,0xDC,0xF8,0xD0,0xC0,0x40,0x00,0x00,0x00,0xC0,0xC2,0x46,0xFC,0x40,
0x00,0x10,0x70,0xC7,0x9E,0xC0,0xFE,0x1C,0x00,0x00,0x00,0x00,0x00,0x00,0x08,0xF0,
0xA0,0xB0,0xB3,0xFF,0xB2,0x90,0xB0,0xF0,0x38,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x80,0x80,0x84,0x84,0x84,0x86,0xB6,0xE6,0x96,0x8E,0x86,0x86,0xC0,0xC0,0x80,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,
0x3F,0xFF,0xFF,0x7F,0xFE,0xFE,0xFE,0xFE,0xFE,0xFE,0x7C,0x0C,0x0C,0x0C,0x0C,0x0C,
0x0C,0x0C,0x0C,0x0C,0x0C,0x0C,0x0C,0xFC,0xFC,0xFE,0xFE,0xFE,0xFE,0xFF,0x7F,0xFF,
0xFF,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x10,0x18,0x89,0x8C,0x96,0xB7,0xD5,0xD6,
0xD6,0xD6,0xDF,0xD7,0xCE,0x5C,0x18,0x18,0x08,0x00,0x00,0x00,0x00,0x40,0x7F,0xB0,
0xD8,0x6C,0x30,0x19,0x0F,0x1F,0x78,0xE0,0xC0,0xC0,0x00,0x00,0x00,0x00,0x08,0x1F,
0x0C,0x0D,0x0C,0x7F,0xC4,0x84,0x86,0x87,0x80,0xF0,0xF0,0xF0,0x00,0x00,0x00,0x00,
0x01,0x01,0x01,0x01,0x31,0x60,0xC0,0xFF,0x3F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x0F,0x7F,0xF8,0xE1,0xE1,0xC1,0xC1,0x81,0x01,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0xC1,0x81,0xC1,0xE1,0xF5,0xFE,0x1F,
0x01,0x00,0x00,0xE0,0xC0,0x60,0x60,0xC0,0xC0,0x00,0x01,0xE1,0xC1,0x61,0x61,0xC1,
0xC1,0x81,0x01,0x01,0xE1,0xE0,0x60,0x60,0xC0,0x80,0x00,0x60,0xF8,0xF8,0x40,0x01,
0xC1,0xE0,0x60,0x60,0xE0,0xC0,0x00,0x01,0xFD,0xF9,0x00,0xF8,0xFC,0x80,0xC0,0xE0,
0x60,0x00,0x00,0x00,0x01,0x01,0x01,0xC1,0xC1,0x61,0x61,0x61,0xE0,0xC0,0x00,0xC0,
0xE0,0x60,0x60,0x60,0xC0,0x00,0x01,0xE1,0xE0,0x60,0x60,0xE0,0xC0,0x60,0x60,0xE0,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x03,0x0F,0x0F,0x1F,0x1F,0x1F,0x1F,0x1F,0x1F,0x03,0x07,0x03,0x03,
0x03,0x03,0x02,0x03,0x03,0x07,0x0F,0x1F,0x1F,0x1F,0x1F,0x1F,0x0F,0x07,0x00,0x00,
0x00,0x00,0x00,0xFF,0xFF,0x10,0x30,0x1F,0x0F,0x00,0x00,0xFF,0xBC,0x10,0x30,0x1F,
0x1F,0x0F,0x00,0x22,0xFF,0x18,0x10,0x10,0x1F,0x0F,0x00,0x00,0x1F,0x1F,0x10,0x08,
0x1E,0x1E,0x13,0x1B,0x1F,0x1F,0x00,0x00,0x1F,0x1F,0x00,0x1F,0x1F,0x03,0x07,0x1E,
0x18,0x00,0x00,0x18,0x18,0x00,0x04,0x0F,0x1D,0x30,0x10,0x10,0x1C,0x1C,0x00,0x0F,
0x1F,0x10,0x30,0x18,0x1F,0x07,0x00,0x1F,0x1F,0x00,0x00,0x1F,0x1F,0x00,0x00,0x1F,
};
void Oled_Show_Image(unsigned char *image)
{
unsigned int j;
unsigned char i; //char范围-128——127,定义char类型会产生越界
for(i = 0;i < 8;i++){
Oled_Write_Cmd(0xB0 + i); //Page0——Page7
Oled_Write_Cmd(0x00); //每个Page从0开始
Oled_Write_Cmd(0x10);
for(j = 128 * i;j < (128 * (i + 1));j++){ //0——127列,依次写入0,每写入数据列地址自动偏移。
Oled_Write_Data(image[j]);
}
}
}
void main()
{
Oled_Init(); //OLED初始化
Oled_Write_Cmd(0x20); //选择一个位置,确认为页面寻址模式
Oled_Write_Cmd(0x02);
Oled_Clear(); //清屏
Oled_Show_Image(bmpImager);
while(1);
}