Q. ntop is a network probe that shows network usage in a way similar to what top does for processes. How do I install latest version of ntop on RHEL 5.x systems?
A. ntop is a network and traffic analyzer that provides a wealth of information on various networking hosts and protocols. ntop is primarily accessed via a built-in web interface.
Following instructions are tested on 32/64 bit versions only:
a) RHEL Linux 5.x
b) CentOS Linux 5.x
Download latest ntop
Visit ntop project to grab latest version. You can use wget to grab the same, enter:# cd /opt
# wget http://freshmeat.net/redir/ntop/7279/url_tgz/ntop-3.3.6.tar.gz
Untar tar ball, enter:# tar -zxvf ntop-3.3.6.tar.gz
Configure and Compile ntop under RHEL
You must have RRDTool installed. You also need to install libpcap, enter:# yum install libpcap-devel libpcap
Type the following commands to compile and install ntop:# cd ntop
# ./autogen.sh
Just type make to compile ntop:# make
Just type make install to install ntop:# make install
# make install-data-as
Create ntop user
Type the following command to run ntop as ntop user, enter:# useradd -M -s /sbin/nologin -r ntop
Setup directory permissions
Next, you need to setup directory permissions, enter:# chown ntop:root /usr/local/var/ntop/
# chown ntop:ntop /usr/local/share/ntop/
Setup ntop user admin password
Type the following command to set ntop admin password, enter:# ntop -A
Sample output:
Mon Jul 28 03:38:34 2008 NOTE: Interface merge enabled by default Mon Jul 28 03:38:34 2008 Initializing gdbm databases ntop startup - waiting for user response! Please enter the password for the admin user: Please enter the password again: Mon Jul 28 03:38:42 2008 Admin user password has been set
Start ntop
Type the following command to start ntop:# /usr/local/bin/ntop -d -L -u ntop -P /usr/local/var/ntop --skip-version-check --use-syslog=daemon
Sample output:
Mon Jul 28 03:42:19 2008 NOTE: Interface merge enabled by default Mon Jul 28 03:42:19 2008 Initializing gdbm databases
If you have multiple interface (eth0, eth1 and so on), start ntop as follows:# /usr/local/bin/ntop -i "eth0,eth1" -d -L -u ntop -P /usr/local/var/ntop --skip-version-check --use-syslog=daemon
Where,
- -i "eth0,eth1" : Specifies the network interface or interfaces to be used by ntop for network monitoring. Here you are monitoring eth0 and eth1.
- -d : Run ntop as a daemon.
- -L : Send all log messages to the system log (/var/log/messages) instead of screen.
- -u ntop : Start ntop as ntop user
- -P /usr/local/var/ntop : Specify where ntop stores database files. You may need to backup database as part of your disaster recovery program.
- --skip-version-check : By default, ntop accesses a remote file to periodically check if the most current version is running. This option disables that check.
- --use-syslog=daemon : Use syslog daemon.
How do I view ntop stats?
By default ntop listen on 3000 port. You can view ntop stats by visiting following url:http://localhost:3000/
ORhttp://server-ip:3000/
(Fig.01: ntop Global TCP/UDP Protocol Distribution Graphs [click to enlarge])
(Fig.02: Network Load Statistics (click to enlarge])
Open port 3000 using iptables
Open /etc/sysconfig/iptables file, enter:# vi /etc/sysconfig/iptables
Append following code before final REJECT line:-A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 3000 -j ACCEPT
Save and close the file. Restart firewall:# service iptables restart
How do I view ntop stats without opening port 3000?
Setup simple tunnel using ssh, enter the following on your local UNIX / Linux desktop system:$ ssh -L 3000:localhost:3000 -N -f [email protected]
Now open browser and type the following command:http://localhost:3000/
How do I start ntop on boot?
Open /etc/rc.local file, enter:# vi /etc/rc.local
Append the following line:/usr/local/bin/ntop -i "eth0,eth1" -d -L -u ntop -P /usr/local/var/ntop --skip-version-check --use-syslog=daemon
Save and close the file.
How do I stop ntop?
Use web interface to shutdown ntop, or use normal kill / killall command:# killall ntop