linux网卡操作命令 ,查看Linux下网卡连接状态（up还是down)?

1. 调整网卡工作模式 

mii-tool -v //查看网卡工作模式

mii-tool -F 100baseTx-FD eth0 //将eth0改为100M,全双工工作模式

mii-tool -r eth0 //恢复 网卡工作模式

ethtool eth0 //查询网卡基本设置

ethtool -s eth0 autoneg off speed 100 duplex full //eth0设置为：100M，全双工，非协商

2. 网卡配置

ifconfig -h //打印帮助信息

ifconfig -a //打印当前网卡信息

ifconfig eth0 192.168.0.1 netmask 255.255.255.0 //设置eth0 IP及掩码

ifconfig eth0:0 192.168.0.2 netmask 255.255.255.0 //设置eth0的第二个IP

ifconfig eth0:1 down //禁用eth0:0

ifconfig eth0 up //启用eth0

ifconfig eth0 hw ether xx:xx:xx:xx:xx:xx //修改网卡MAC地址

ifconfig eth0 promisc //设置网卡工作于混杂模式下

iwconfig eth0 essid "tao" //设置无线网卡的essid为“tao”

iwconfig eth0 mode Managed //设置无线网卡工作在Managed模式下

iwconfig eth0 mode Ad-hoc // 设置无线网卡工作在Ad-hoc模式下

iwconfig eth0 freq 2.422G //设置 无线网卡工作频率

3.查看Linux下网卡连接状态（up还是down)?

 

1) 通过mii-tool指令

[root@localhost root]# mii-tool

eth0: negotiated 100baseTx-FD, link ok

eth1: no link

或

[root@localhost root]# mii-tool -v

eth0: negotiated 100baseTx-FD, link ok

product info: vendor 00:50:43, model 2 rev 3

basic mode: autonegotiation enabled

basic status: autonegotiation complete, link ok

capabilities: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD

advertising: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control

link partner: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD

eth1: no link

product info: vendor 00:50:43, model 2 rev 3

basic mode: autonegotiation enabled

basic status: no link

capabilities: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD

advertising: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control

或

[root@localhost root]# mii-tool -w

21:20:33 eth0: negotiated 100baseTx-FD, link ok

21:20:33 eth1: no link

 

//mii-tool主要是用于配置网卡工作模式的指令，同时也可以进行查询、监控等工作！

 

2)ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:09:6B:09:08:FC
inet addr:192.168.10.1 Bcast:192.168.10.255 Mask:255.255.255.0
inet6 addr: fe80::209:6bff:fe09:8fc/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1   // RUNNING表示up

3) ethtool eth1
Settings for eth1:
        Supported ports: [ TP MII ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
        Supports auto-negotiation: Yes
        Advertised link modes:  10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
        Advertised auto-negotiation: Yes
        Speed: 100Mb/s
        Duplex: Full
        Port: MII
        PHYAD: 32
        Transceiver: internal
        Auto-negotiation: on
        Supports Wake-on: pumbg
        Wake-on: d
        Current message level: 0x00000007 (7)
        Link detected: yes  //表示物理口up

 4、linux查看网卡吞吐量，实时网络带宽

1） dmesg | grep -i eth

2) ethtool eth1
Settings for eth1:
        Supported ports: [ TP MII ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
        Supports auto-negotiation: Yes
        Advertised link modes:  10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
        Advertised auto-negotiation: Yes
        Speed: 100Mb/s
        Duplex: Full
        Port: MII
        PHYAD: 32
        Transceiver: internal
        Auto-negotiation: on
        Supports Wake-on: pumbg
        Wake-on: d
        Current message level: 0x00000007 (7)
        Link detected: yes //表示物理口 up

 

查看网络实时带宽

在 linux的proc文件系统中，通过查看/proc/net/dev文件
可以得到每个网络接口的吞吐量，但是无法获得实时带宽