浮动静态路由的配置

要求：

如下图所示，R1有两条路径可以到达192.168.1.0/24网段，其中R2之间通过RIP学习到了192.168.1.0/24的路由，另外和R3之间，由于某些原因无法通过动态路由协议学习到路由，只能通过静态路由的方式。

现在希望达到这样的一种冗余效果:

1.R1的两条路径通过浮动路由来进行冗余备份；

2.R1和R2之间的链路作为主链路，.R1和R3之间的链路作为备份链路；

 

实验过程：

1.       R1的配置

Router>en Router#config t Enter configuration commands, one per line.  End with CNTL/Z. Router(config)#no ip domain-lookup Router(config)#line con 0 Router(config-line)#no exec-timeout Router(config-line)#loggin syn Router(config-line)#exit Router(config)#host R1 R1(config)#int s0/0 R1(config-if)#no shut R1(config-if)#ip add 172.16.1.10 255.255.255.0 R1(config-if)#int s0/1 R1(config-if)#no shut R1(config-if)#ip add 172.16.2.10 255.255.255.0 R1(config-if)#exit R1(config)#router rip R1(config-router)#version 2 R1(config-router)#no auto R1(config-router)#net 172.16.1.0 R1(config-router)#exit

 

2.       R2的配置

Router>en Router#config t Enter configuration commands, one per line.  End with CNTL/Z. Router(config)#no ip domain-lookup Router(config)#line con 0 Router(config-line)#no exec-timeout Router(config-line)#loggin syn Router(config-line)#exit Router(config)#host R2 R2(config)#int s0/0 R2(config-if)#no shut R2(config-if)#ip add 172.16.1.1 255.255.255.0 R2(config-if)#int e1/0 R2(config-if)#no shut R2(config-if)#ip add 192.168.1.1 255.255.255.0 R2(config-if)#exit R2(config)#router rip R2(config-router)#version 2 R2(config-router)#no auto R2(config-router)#net 172.16.1.0 R2(config-router)#net 192.168.1.0 R2(config-router)#end

3.       R3的配置

Router#config t Enter configuration commands, one per line.  End with CNTL/Z. Router(config)#no ip domain-lookup Router(config)#line con 0 Router(config-line)#no exec-timeout Router(config-line)#loggin syn Router(config-line)#exit Router(config)#host R3 R3(config)#int s0/1 R3(config-if)#no shut R3(config-if)#ip add 172.16.2.1 255.255.255.0 R3(config-if)#int e1/0 R3(config-if)#no shut R3(config-if)#ip add 192.168.1.2 255.255.255.0 R3(config-if)#exit

4.       R4（模拟192.168.1.0/24网段）的配置

Router>en Router#config t Enter configuration commands, one per line.  End with CNTL/Z. Router(config)#no ip domain-lookup Router(config)#line con 0 Router(config-line)#no exec-timeout Router(config-line)#loggin syn Router(config-line)#exit Router(config)#host R4 R4(config)#int e1/0 R4(config-if)#no shut R4(config-if)#ip add 192.168.1.10 255.255.255.0 R4(config-if)#exit R4(config)#router rip R4(config-router)#version 2 R4(config-router)#no auto R4(config-router)#net 192.168.1.0 R4(config-router)#end

5.       查看R1的路由表

R1#show ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP        D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area        N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2        E1 - OSPF external type 1, E2 - OSPF external type 2        i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2        ia - IS-IS inter area, * - candidate default, U - per-user static route        o - ODR, P - periodic downloaded static route   Gateway of last resort is not set        172.16.0.0/24 is subnetted, 2 subnets C       172.16.1.0 is directly connected, Serial0/0 C       172.16.2.0 is directly connected, Serial0/1 R    192.168.1.0/24 [120/1] via 172.16.1.1, 00:00:11, Serial0/0  //通过RIP学习到的路由

6.       测试R1到R2连通性

R1#ping 192.168.1.10 source 172.16.1.10   Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.1.10, timeout is 2 seconds: Packet sent with a source address of 172.16.1.10 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 12/44/92 ms R1#traceroute 192.168.1.10 source 172.16.1.10   Type escape sequence to abort. Tracing the route to 192.168.1.10     1 172.16.1.1 32 msec 60 msec 16 msec  //R1和R4通信经过R2   2 192.168.1.10 44 msec *  16 msec

7.       在R1上配置静态路由

R1(config)#ip route 192.168.1.0 255.255.255.0 172.16.2.1

8.       再次测试连通性

R1#ping 192.168.1.10 source 172.16.1.10        Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.1.10, timeout is 2 seconds: Packet sent with a source address of 172.16.1.10 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 12/41/76 ms R1#traceroute 192.168.1.10                     Type escape sequence to abort. Tracing the route to 192.168.1.10     1 172.16.2.1 84 msec 40 msec 8 msec   2 192.168.1.10 52 msec *  44 msec  //R1和R4通信走了R3

9.       查看R1路由表

R1#show ip route                             Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP        D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area        N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2        E1 - OSPF external type 1, E2 - OSPF external type 2        i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2        ia - IS-IS inter area, * - candidate default, U - per-user static route        o - ODR, P - periodic downloaded static route   Gateway of last resort is not set        172.16.0.0/24 is subnetted, 2 subnets C       172.16.1.0 is directly connected, Serial0/0 C       172.16.2.0 is directly connected, Serial0/1 S    192.168.1.0/24 [1/0] via 172.16.2.1  //路由表里面只有一条静态路由，而没有RIP的路由，这是因为静态路由的AD比RIP的AD小

10.   根据题目要求，R1和R2之间的链路作为主链路，.R1和R3之间的链路作为备份链路，我们需要给R1配置一条浮动静态路由。

11.   在R1上配置一条浮动静态路由

R1(config)#ip route 192.168.1.0 255.255.255.0 172.16.2.1 125  //配置一条静态路由，AD为125 R1(config)#end R1#clear ip route *  //刷新路由表

12.   再次查看R1的路由表

R1#show ip route   Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP        D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area        N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2        E1 - OSPF external type 1, E2 - OSPF external type 2        i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2        ia - IS-IS inter area, * - candidate default, U - per-user static route        o - ODR, P - periodic downloaded static route   Gateway of last resort is not set        172.16.0.0/24 is subnetted, 2 subnets C       172.16.1.0 is directly connected, Serial0/0 C       172.16.2.0 is directly connected, Serial0/1 R    192.168.1.0/24 [120/1] via 172.16.1.1, 00:00:01, Serial0/0  //RIP学习到的路由又再一次出现在路由表

13.   模拟故障，关闭R2的s0/0口

R2(config)#int s0/0 R2(config-if)#shut

14.   再次查看R1的路由表

R1#clear ip route * R1#show ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP        D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area        N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2        E1 - OSPF external type 1, E2 - OSPF external type 2        i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2        ia - IS-IS inter area, * - candidate default, U - per-user static route        o - ODR, P - periodic downloaded static route   Gateway of last resort is not set        172.16.0.0/24 is subnetted, 2 subnets C       172.16.1.0 is directly connected, Serial0/0 C       172.16.2.0 is directly connected, Serial0/1 S    192.168.1.0/24 [125/0] via 172.16.2.1  //静态路由出现在了路由表中 说明：R1的两条路径通过浮动路由来进行冗余备份