思科交换机2960G重灌IOS
本文转载自 胖鲨鱼网络 http://www.pangshayu.com/html/6010.html
关键字：思科交换机,CISCO2960,重灌IOS,重装IOS,switch:
公司的一台思科2960交换机拿来设置，在清空配置的时候不小心清空了Flash：结果reload启动不起来，直接进入了"SWITCH：”模式。
然后就Boot启动：
switch: boot
Loading "flash:c2960-lanbasek9-mz.122-44.SE6/c2960-lanbasek9-mz.122-44.SE6.bin".
..flash:c2960-lanbasek9-mz.122-44.SE6/c2960-lanbasek9-mz.122-44.SE6.bin: no such
file or directory
Error loading "flash:c2960-lanbasek9-mz.122-44.SE6/c2960-lanbasek9-mz.122-44.SE6
.bin"
Interrupt within 5 seconds to abort boot process.
Boot process failed...
结果如上，还是不行加载不上IOS，然后我就做了Reset动作：
switch: reset
Are you sure you want to reset the system (y/n)?y
System resetting...
Boot Sector Filesystem (bs) installed, fsid: 2
Base ethernet MAC Address: ac:a0:16:59:6e:00
Xmodem file system is available.
The password-recovery mechanism is enabled.
Initializing Flash...
flashfs[0]: 0 files, 1 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 32514048
flashfs[0]: Bytes used: 1024
flashfs[0]: Bytes available: 32513024
flashfs[0]: flashfs fsck took 9 seconds.
...done Initializing Flash.
done.
Loading "flash:c2960-lanbasek9-mz.122-44.SE6/c2960-lanbasek9-mz.122-44.SE6.bin".
..flash:c2960-lanbasek9-mz.122-44.SE6/c2960-lanbasek9-mz.122-44.SE6.bin: no such
file or directory
Error loading "flash:c2960-lanbasek9-mz.122-44.SE6/c2960-lanbasek9-mz.122-44.SE6
.bin"
Interrupt within 5 seconds to abort boot process.
Boot process failed...
The system is unable to boot automatically. The BOOT
environment variable needs to be set to a bootable
image.
错误提示是"Error loading "flash:c2960-lanbasek9-mz.122-44.SE6/c2960-lanbasek9-mz.122-44.SE6
.bin"。加载不上c2960的IOS文件。为了确认Flash中是否真的没有IOS文件，我加载flash查看：
switch: flash_init
Initializing Flash...
...The flash is already initialized.
switch: dir flash:
Directory of flash:/
32513024 bytes available (1024 bytes used)
switch:
结果还真的什么也没有，My God！真的是给清空了，好吧，只有重灌了。在网上Downloa IOS文件：c2960-lanbasek9-mz.122-44.SE6.bin，或者去CISO官网Download最新的IOS。
下载好后准备Cisco TFTP软件，准备重灌。要在SWITCH模式下用Xmodem方式灌才可以。方法如下：
1.用C**ole控制台连接交换机(这是必须的，已经在连接了)。
2.打开TFTP服务。
3.在超级终端里输入：
switch:copy xmodem：flash：c2960-lanbasek9-mz.122-44.SE6.bin
Begin the Xmodem or Xmodem-1K transfer now...
CCCCC
此时会出现CCCCCC字符，说明正在传送文件。
4.还要在超级终端菜单的"传送-->发送文件"，在协力选项中选择Xmodem或着Xmodem-1K协议，然后选择IOS的相应文件(就是刚才输入的c2960-lanbasek9-mz.122-44.SE6.bin)，开始正式传送。
选择Xmodem协议传送，有时会传送失败，Xmodem协议不行就选择1K Xmodem协议。我就是用1K Xmodem协议传送成功的。传送过程会很长，要1-2个小时，看文件大小，要慢慢等。等传送进度条跑完，会出现一下界面和提示：8888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888..........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................
File “xmodem:” successfully copied to "flash:c2960-lanbasek9-mz.122-44.SE6.bin"
switch: