apache+mysql+GD+php

 

==================================LADP安装=====================
总共11个源码包
autoconf-2.61.tar.gz
httpd-2.2.8.tar.gz
libxml2-2.6.19.tar.gz
mysql-5.0....
freetype-2.1.10.tar.gz
jpegsrc.v6b.tar.gz
libpng-1.2.24.tar.gz
zlib-1.2.3.tar.gz
gd-2.0.35.tar.gz
php-5.2.5.tar.gz

检查环境是否安装gcc
# gcc -v

安装GD库==============================
安装前应先依次安装zlib/libpng/freetype/jpegsrc.v6b/autoconf/gd

安装zlib
tar xzvf zlib-1.2.3.tar.gz
cd zlib-1.2.3
./configure --prefix=/usr/local/zlib
make
make install

安装libpng
tar xzvf libpng-1.2.24.tar.gz
cd libpng-1.2.24
cp scripts/makefile.linux makefile
make
make install

安装freetype TTF包
tar xzvf freetype-2.1.10.tar.gz
cd freetype-2.1.10
mkdir -p /usr/local/freetype
./configure --prefix=/usr/local/freetype
make
make install

安装jpeg6
tar xzvf jpegsrc.v6b.tar.gz
cd jpeg-6b
mkdir -p /usr/local/jpeg6
mkdir -p /usr/local/jpeg6/bin
mkdir -p /usr/local/jpeg6/lib
mkdir -p /usr/local/jpeg6/include
mkdir -p /usr/local/jpeg6/man
mkdir -p /usr/local/jpeg6/jpeg6man1
mkdir -p /usr/local/jpeg6/man/man1
./configure --prefix=/usr/local/jpeg6 --enable-share --enable-static
make
make install
最后安装jpeg6库文件
make install-lib
使用libtool完成库的安装
libtool --finish /usr/local/jpeg6//lib //

安装autoconf
tar xzvf autoconf-2.61.tar.gz
cd autoconf-2.61
./configure --prefix=/usr
make
make install

安装GD
tar xzvf gd-2.0.35.tar.gz
cd gd-2.0.35
./configure --prefix=/usr/local/gd --with-jpeg=/usr/local/jpeg6 --with-png=/usr/local/lib --with-zlib=/usr/local/zlib --with-freetype=/usr/local/freetype
make
make install
cp gd.h /usr/local/lib #将生成的头文件拷贝到lib目录下，否则会出

安装freetds (用来连接MS SQLServer和Sybase数据库更具需要是否安装)
tar xzvf freetds-0.82.tar.gz
cd freetds-0.82
./configure --prefix=/usr/local/freetds --with-tdsver=8.0
make
make install

安装mysql===见另外文章==================================
安装apache===见另外文章=================================

./configure --prefix=/usr/local/apache2 --enable-so --enable-ssl=static --with-ssl=/usr/local/ssl --with-z-dir=/usr/local/zlib

设置apache 自启动
echo "/usr/local/apache2/bin/apachectl start">>/etc/rc.d/rc.local
检查是否加入自启动了
cat /etc/rc.d/rc.local

安装PHP
PHP 对XML的支持是建立在libxml2库的基础上的

安装php之前先安装libxml2
tar -zxvf libxml2-2.6.19.tar.gz
cd libxml2-2.6.19
mkdir -p /usr/local/libxml2
./configure --prefix=/usr/local/libxml2
make
make install
复制配置文件
cp xml2-config /usr/bin
检查系统是否已经安装php，如果安装将其卸载
将多个相关软件包一次性卸载：
for i in 'rpm -qa | grep -i php'
>do rpm -e $i --nodeps
>done

 

php必要的选项:
--prefix=/usr/local/php
--with-apxs2=/usr/local/apache/bin/apxs
--with-mysql=/usr/local/mysql/
--with-libxml-dir
--enable-mbstring

这是让PHP支持GD库的配置选项:
--with-gd=/usr/local/gd2/
--with-jpeg-dir=/usr/local/jpeg6/
--with-png
--with-zlib-dir=/usr/lib
--with-freetype-dir=/usr/local/freetype

tar -zxvf php-5.2.5.tar.gz
cd php-5.2.5
mkdir -p /usr/local/php5
./configure --prefix=/usr/local/php5 --with-apxs2=/usr/local/apache2/bin/apxs --with-mysql=/usr/local/mysql --with-libxml-dir=/usr/local/libxml2 --with-png-dir=/usr/local/lib --with-jpeg-dir=/usr/local/jpeg6 --with-zlib-dir=/usr/local/zlib --with-freetype-dir=/usr/local/freetype --with-gd=/usr/local/gd --enable-soap --enable-mbstring=all --with-mssql=/usr/local/freetds
make
make test
make install

##make时报错make: *** [sapi/cli/php] Error 1
解决方法：make ZEND_EXTRA_LIBS='-liconv'

建立php配置文件
cp php.ini-dist /usr/local/php5/lib/php.ini
修改apache配置文件添加php支持
vi /usr/local/apache2/conf/httpd.conf
加入(注意之前加过了就不用再加，否则apache不能启动：
LoadModule php5_module modules/libphp5.so 在此下面加入以下
AddType application/x-httpd-php .php
建立简单的php测试文件
<?php
phpinfo()
?>

 

/usr/local/apache2/bin/apachectl restart
如果碰到：
httpd: Syntax error on line 55 of /usr/local/apache2/conf/httpd.conf: Cannot load /usr/local/apache2/modules/libphp5.so into server: /usr/local/apache2/modules/libphp5.so: cannot restore segment prot after reloc: Permission denied
则需要运行：
chcon -t textrel_shlib_t /usr/local/apache2/modules/*.so
或者干脆关闭SELinux:
vi /etc/selinux/config
把文件中的SELINUX="enforcing" 改为 disabled
setenforce 0 让selinux生效

//可以不装这个ZendOptimizer-3.3.0a-linux-glibc21-i386.tar.gz
ZendOptimizer用来加速php
tar zxvf ZendOptimizer-3.3.0a-linux-glibc21-i386.tar.gz
#cd ZendOptimizer-3.3.0a-linux-glibc21-i386
#./install.sh
按照按照步骤安装 输入正确的安装apache的路径等内容!
安装完毕,再看看phpinfo页面的zend选项就发现了!!