基于S3C2410平台的Linux 2.6.14内核+平台驱动的移植指南（最终版）
基于S3C2410平台移植Linux 2.6.14内核&驱动指南
安装交叉编译工具
Ø
下载交叉编译工具
（本文默认所有软件均下载在用户主目录下）
arm-linux-gcc-3.4.1 —— 交叉编译工具
URL: ftp://ftp.handhelds.org/projects/toolchain/arm-linux-gcc-3.4.1.tar.bz2
Ø
安装
//将压缩包移动至根目录下
#mv arm-linux-gcc-3.4.1.tar.bz2 /
//解压，默认路径为 /usr/local/arm /3.4.1
#tar jxvf arm-linux-gcc-3.4.1.tar.gz2
下载Linux内核
Ø
下载
Linux 2.6.14
内核
URL: http://www.kernel.org/pub/linux/kernel/v2.6/linux-2.6.14.tar.bz2
Ø
解压内核
#cd ~
#tar jxvf linux-2.6.14.tar.bz2
建立环境变量
Ø
将交叉编译工具路径和内核路径加入环境变量
#vi ~/.bashrc
export KERNEL=~/linux-2.6.14
export PATH=/usr/local/arm/3.4.1/bin:$PATH
内核移植
Ø
为
Flash
进行分区
启动开发板，进入vivi，对vivi进行分区操作
vivi>bon part 0 128k 192k 2240k 5312k:m 64704k
分区信息如下所示：
|
分区
|
起始地址
|
分区大小
|
分区作用
|
|
Part0
|
0x0
|
0x00020000 (128k)
|
bootloader
|
|
Part1
|
0x00020000
|
0x00010000 (64k)
|
bootloader params
|
|
Part2
|
0x00030000
|
0x00200000 (2m)
|
linux kernel
|
|
Part3
|
0x00230000
|
0x00300000 (3m)
|
root filesystem
|
|
Part4
|
0x00530000
|
0x03A00000 (58m)
|
yaffs filesystem
|
将vivi写进Flash
vivi>load flash vivi x
Ø
修改
Makefile
#vi $KERNEL/Makefile
找到ARCH与CROSS_COMPILE，修改为
ARCH ?= arm
CROSS_COMPILE ?= arm-linux-
Ø
将分区信息加入内核
#vi $KERNEL/arch/arm/mach-s3c2410/devs.c
添加头文件：
#include <linux/mtd/partitions.h>
#include <linux/mtd/nand.h>
#include <asm/arch/nand.h>
添加分区结构：
static struct mtd_partition partition_info[]={
{
name: "loader", //分区名字，任意
size: 0x00020000, //分区大小
offset: 0x0, //分区的起始地址，相对于0x0的偏移
},{
name: "param",
size: 0x00010000,
offset: 0x00020000,
},{
name: "kernel",
size: 0x00200000,
offset: 0x00030000,
},{
name: "rootfs",
size: 0x00300000,
offset: 0x00230000,
},{
name: "yaffs",
size: 0x03A00000,
offset: 0x00530000,
}
};
struct s3c2410_nand_set nandset={
nr_partitions: 5, //分区数量
partitions: partition_info, //分区表
};
struct s3c2410_platform_nand superlpplatform={
//NAND Flash芯片支持
//参数意义可参考S3C2410手册
tacls: 0,
twrph0: 30,
twrph1: 0,
sets: &nandset,
nr_sets: 1,
};
修改s3c_device_nand，以加入NAND Flash驱动：
struct platform_device s3c_device_nand = {
.name = "s3c2410-nand", //设备名称
.id = -1, //有效设备编号，-1表示唯一设备
.num_resources = ARRAY_SIZE(s3c_nand_resource), //寄存器区的个数
.resource = s3c_nand_resource, //寄存器区的首地址
//添加如下信息，表示NAND Flash设备
.dev={
.platform_data=&superlpplatform
}
};
Ø
指定启动时的设备初始化
#vi $KERNEL/arch/arm/mach-s3c2410/mach-smdk2410.c
修改：
static struct platform_device *smdk2410_devices[] __initdata = {
s3c_device_usb,
s3c_device_lcd,
s3c_device_wdt,
s3c_device_i2c,
s3c_device_iis,
//添加如下信息
s3c_device_nand,
};
Ø
禁止
Flash ECC
效验
内核通过vivi把数据写入NAND Flash，而vivi的ECC效验算法和内核的不同，内核的效验码是由NAND Flash控制器产生的，所以在此必须禁用NAND Flash ECC。
#vi $KERNEL/drivers/mtd/nand/s3c2410.c
找到s3c2410_nand_init_chip函数，将chip->eccmode的值修改为：
NAND_ECC_NONE
Ø
修正
Kernel
错误
编辑partitions.h，增加list.h头文件。
#vi $KERNEL/include/linux/mtd/partitions.h
在头文件中添加：
#include <linux/list.h>
Ø
加载
DEVFS
#vi $KERNEL/fs/Kconfig
查找“Pseudo filesystems”
在其下添加如下语句：
config DEVFS_FS
bool "/dev file system support (OBSOLETE)"
default y
config DEVFS_MOUNT
bool "Automatically mount at boot"
default y
depends on DEVFS_FS
Yaffs2加载
Ø
下载
Yaffs2
URL: http://www.aleph1.co.uk/cgi-bin/viewcvs.cgi/yaffs2.tar.gz?view=tar
Ø
解压
Yaffs2
并将其加入
Linux
内核
#cd ~
#tar zxvf yaffs2.tar.gz
#cd yaffs2
#sh patch-ker.sh c $KERNEL
USB Host Driver 移植
Ø
初始化
USB Host Driver
由于Linux 2.6.14内核已经包含了s3c2410的USB驱动，所以只要在平台初始化文件中对USB进行设置、初始化即可。
#vi $KERNEL/arch/arm/mach-s3c2410/mach-smdk2410.c
添加头文件：
#include <asm/arch/usb-control.h>
#include <asm/arch/regs-clock.h>
#include <linux/device.h>
#include <linux/delay.h>
添加USB Host Driver注册信息：
struct s3c2410_hcd_info usb_s3c2410_info = {
.port[0] = {
.flags = S3C_HCDFLG_USED
}
};
int smdk2410_usb_init(void)
{
/* USB */
unsigned long upllvalue = (0x78<<12)|(0x02<<4)|(0x03);
printk("USB Control, (c) 2006 s3c2410/n");
s3c_device_usb.dev.platform_data = &usb_s3c2410_info;
while(upllvalue!=__raw_readl(S3C2410_UPLLCON))
{
__raw_writel(upllvalue,S3C2410_UPLLCON);
mdelay(1);
}
return 0;
}
在smdk2410_map_io函数中调用 usb 的初始化，如下所示：
static void __init smdk2410_map_io(void)
{
…… //代码省略
smdk2410_usb_init();
}
LCD移植
Ø
参考资料
S3C2410X User Manual
作用：参考LCD各寄存器的地址、置位等信息
LCD技术手册
作用：参看LCD的技术指标
（由于本人使用的是Uptech 2410-s开发板，所以使用的液晶屏是Sharp LQ080V3DG01）
Ø
初始化
LCD
由于Linux 2.6.14内核已经包含了该驱动，所以只要在平台初始化文件中对LCD进行设置、初始化即可。
#vi $KERNEL/arch/arm/mach-s3c2410/mach-smdk2410.c
添加头文件：
#include <asm/arch/regs-lcd.h>
#include <asm/arch-s3c2410/fb.h>
添加LCD初始化代码：
static struct s3c2410fb_mach_info s3c2410_lcd_info __initdata = {
.fixed_syncs = 0,
.regs = {
//对于寄存器的设置是关键，可参考S3C2410X的手册
//和LCD技术手册中对于LCD技术指标的描述来进行设置。
//其中，寄存器值的宏定义在regs-lcd.h文件中。
.lcdcon1 = S3C2410_LCDCON1_TFT16BPP
| S3C2410_LCDCON1_TFT | S3C2410_LCDCON1_CLKVAL(1),
.lcdcon2 = S3C2410_LCDCON2_VBPD(32)
| S3C2410_LCDCON2_VFPD(9) | S3C2410_LCDCON2_VSPW(1),
.lcdcon3 = S3C2410_LCDCON3_HBPD(47)
| S3C2410_LCDCON3_HFPD(15),
.lcdcon4 = S3C2410_LCDCON4_MVAL(13)
| S3C2410_LCDCON4_HSPW(95),
.lcdcon5 = S3C2410_LCDCON5_FRM565
| S3C2410_LCDCON5_INVVLINE | S3C2410_LCDCON5_HWSWP
| S3C2410_LCDCON5_PWREN | S3C2410_LCDCON5_INVVFRAME,
},
.lpcsel = 0x0,
.gpccon = 0xaaaaaaaa,
.gpccon_mask = 0xffffffff,
.gpcup = 0xffffffff,
.gpcup_mask = 0xffffffff,
.gpdcon = 0xaaaaaaaa,
.gpdcon_mask = 0x0,
.gpdup = 0xffffffff,
.gpdup_mask = 0xffffffff,
.width = 640,
.height = 480,
.xres = {640,640,640},
.yres = {480,480,480},
.bpp = {16,16,16},
};
static void __init smdk2410_lcd_init(void)
{
set_s3c2410fb_info(&s3c2410_lcd_info);
}
最后在MACHINE_START与MACHINE_END中添加如下代码：
.init_machine = smdk2410_lcd_init,
NE2000兼容网卡移植（AX88796）
Ø
定义网卡
I/O
地址
在S3C2410平台关于内存地址映射的头文件中增加对网卡的支持。
#vi $KERNEL/include/asm-arm/arch-s3c2410/map.h
添加代码：
#define pAX88796_BASE (0x10000000) //physical base address
#define vAX88796_BASE
(0xd1000000) //virtual base address
#define AX88796_BASE
(vAX88796_BASE + 0x200) //bank2 base address
Ø
地址映射
将之前定义的网卡物理I/O地址和虚拟I/O地址间的映射关系注册到平台初始化文件中。
#vi $KERNEL/arch/arm/mach-s3c2410/mach-smdk2410.c
修改：
static struct map_desc smdk2410_iodesc[] __initdata = {
//添加如下映射关系
//{虚拟地址, 物理地址, 地址空间大小, 设备类型}
{vAX88796_BASE, pAX88796_BASE, SZ_1M, MT_DEVICE},
};
Ø
修改
NE2000
驱动文件
（基于Uptech 2410-s平台，其使用的是NE2000兼容的AX88796芯片）
#vi $KERNEL/drivers/net/ne.c
添加头文件：
#include <asm/hardware.h>
#include <asm/irq.h>
#include <asm/arch/irqs.h>
#include <asm/arch/regs-mem.h>
#include <asm/arch/regs-gpio.h>
#include <asm/arch/map.h>
修改驱动：
//根据开发板上网卡和S3C2410的连接，确定外部中断
#define IRQ_NE2000 IRQ_EINT2
//定义网卡MAC地址
unsigned char ne_defethaddr[] = { 0x00, 0xd0, 0xcf, 0x00, 0x00, 0x01 };
//确保总线宽度为16位
#if 0
#if defined(CONFIG_PLAT_MAPPI)
# define DCR_VAL 0x4b
#elif defined(CONFIG_PLAT_OAKS32R)
# define DCR_VAL 0x48
//8-bit
#else
# define DCR_VAL 0x49 //16-bit
#endif
#endif
#define DCR_VAL 0x49
/*** 这里的代码主要参考THREEWATER的文章 ***/
/*
NE2000网卡的初始化代码在do_ne_probe函数中，在该函数调用时，网卡设备的基地址空间、寄存器、中断等资源都未指定，所以在这里为该平台进行资源分配。
*/
#ifndef MODULE
int orig_irq = dev->irq;
#endif
//添加如下代码
static int once = 0;
unsigned int value = 0;
if(once)
{
return -ENXIO;
}
//设置BWSCON寄存器：Bus Width & Wait Control Register
//这里AX88796在BANK2空间，设置BANK2的16-bit总线和停止状态等信息
value = __raw_readl(S3C2410_BWSCON);
value &= ~(S3C2410_BWSCON_ST2
| S3C2410_BWSCON_WS2 | S3C2410_BWSCON_DW2_32);
value |= (S3C2410_BWSCON_ST2 | S3C2410_BWSCON_DW2_16);
printk(KERN_INFO"s3c2410_bwscon value %x/n", value);
__raw_writel(value, S3C2410_BWSCON);
value = 0;
//设置BANKCON寄存器：Bank Control Register
//设置AX88796所在BANK2空间的时序信息
value = S3C2410_BANKCON_Tacs4
| S3C2410_BANKCON_Tcos4 | S3C2410_BANKCON_Tacc14
| S3C2410_BANKCON_Tcoh4 | S3C2410_BANKCON_Tcah4
| S3C2410_BANKCON_Tacp6 | S3C2410_BANKCON_PMCnorm;
printk(KERN_INFO"s3c2410_bankcon2 value %x/n", value);
__raw_writel(value, S3C2410_BANKCON2);
//设置AX88796的中断触发方式为低电平有效
set_irq_type(IRQ_NE2000, IRQT_LOW);
printk(KERN_INFO"ax88796 extIRQ = %x, IRQtype= %x/n",
IRQ_NE2000, IRQT_LOW);
s3c2410_gpio_cfgpin(S3C2410_GPF2, S3C2410_GPF2_EINT2);
s3c2410_gpio_pullup(S3C2410_GPF2, 0);
//指定AX88796的基地址空间和使用的中断号
if(base_addr == 0)
{
dev->base_addr = base_addr = AX88796_BASE;
dev->irq = IRQ_NE2000;
once++;
}
/*
网卡的主要检测工作在ne_probe1函数中完成，其中最主要的是读取和配置网卡的MAC地址等信息。这里对AX88796的MAC地址的设置和典型的网卡不同。一般的网卡通过读取连接在NE2000网卡上的EEPROM的代码，而现在的平台并没有使用配置存储器，所以需要修改ne_probe1函数，设置网卡的MAC地址。
*/
{
……
for (i = 0; i < sizeof(program_seq)/sizeof(program_seq[0]); i++)
outb_p(program_seq[i].value, ioaddr + program_seq[i].offset);
}
//添加并修改如下代码
{
//设置MAC地址
unsigned char *ep;
ep = (unsigned char *)&ne_defethaddr[0];
ne_defethaddr[5]++;
for(i = 0; i < 6; i++)
{
SA_prom[i] = ep[i];
}
SA_prom[14] = SA_prom[15] = 0x57;
wordlength = 2;
}
//取消读取EEPROM的代码
#if 0
for(i = 0; i < 32; i+=2) {
SA_prom[i] = inb(ioaddr + NE_DATAPORT);
SA_prom[i+1] = inb(ioaddr + NE_DATAPORT);
if (SA_prom[i] != SA_prom[i+1])
wordlength = 1;
}
#endif
if (wordlength == 2)
{
#if 0
for (i = 0; i < 16; i++)
SA_prom[i] = SA_prom[i+i];
#endif
……
#if 0
if (dev->irq < 2)
{
unsigned long cookie = probe_irq_on();
outb_p(0x50, ioaddr + EN0_IMR); // Enable one interrupt.
outb_p(0x00, ioaddr + EN0_RCNTLO);
outb_p(0x00, ioaddr + EN0_RCNTHI);
outb_p(E8390_RREAD+E8390_START, ioaddr); // Trigger it...
mdelay(10); // wait 10ms for interrupt to propagate
outb_p(0x00, ioaddr + EN0_IMR); // Mask it again.
dev->irq = probe_irq_off(cookie);
if (ei_debug > 2)
printk(" autoirq is %d/n", dev->irq);
} else if (dev->irq == 2)
// Fixup for users that don't know that IRQ 2 is really IRQ 9,
// or don't know which one to set.
dev->irq = 9;
#endif
Ø
开启内核对
NE2000
兼容网卡的支持
#vi arch/arm/Kconfig
//修改如下代码
config ISA
bool "ISA support"
default y
help
Find out whether you have ISA slots on your motherboard. ISA is the name of a bus system, i.e. the way the CPU talks to the other stuff inside your box. Other bus systems are PCI, EISA, MicroChannel (MCA) or VESA. ISA is an older system, now being displaced by PCI; newer boards don't support it. If you have ISA, say Y, otherwise N.
只有开启了ISA设备支持，在配置内核时，才会在Network device support中出现对于NE2000兼容网卡的支持选项。
Ø
问题解答
（1） Kernel panic：很有可能是没有做虚拟地址到物理地址的映射，内核在访问虚拟地址的时候，找不到对应的物理地址入口。
（2） eth0: interrupt from stopped card：看上去是中断问题，但我在移植过程中发现是网卡的虚拟地址设置错误，导致内核访问到了其它不存在的外设上。
（3） NETDEV WATCHDOG: eth0: transmit timed out：出现这个错误的情况很复杂，我移植的时候碰到过两次，第一次是BANK空间的地址总线没有设置，默认是8bit，应该设成16bit；第二次是网络物理连接故障。出现这些错误，假如不知道如何入手的话，可以在windows下使用sniffer pro进行抓包分析。
内核配置（.config）与编译
Ø
内核配置
（见附录）
Ø
编译内核
#make zImage
修改根文件系统
在宿主机上进入目录/arm2410s（博创2410-s平台提供），该目录下的root目录就是一个制作好的根文件系统。在此基础上，我们要对root/etc/fstab分区配置文件进行修改，用来挂载Yaffs文件系统。
#vi /arm2410s/root/etc/fstab
找到yaffs，修改为：
/dev/mtdblock/4
/mnt/yaffs yaffs defaults 1 1
然后制作根文件系统镜像。
#mkcramfs root root.cramfs
安装内核和根文件系统
Ø
将编译好的内核
2.6.14
写入
Flash
vivi>load kernel x
Ø
将制作的根文件系统
root.cramfs
写入
Flash
vivi>load root x
Ø
修改
vivi
启动参数
vivi>param set linux_cmd_line “
noinitrd root=/dev/mtdblock3 init=/linuxrc console=ttySAC0,115200”
vivi>param save
Ø
重启开发板，完成工作。
附录：内核配置文件.config
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.14
# Fri Oct 19 17:33:32 2007
#
CONFIG_ARM=y
CONFIG_MMU=y
CONFIG_UID16=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
CONFIG_CLEAN_COMPILE=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_INIT_ENV_ARG_LIMIT=32
#
# General setup
#
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
# CONFIG_POSIX_MQUEUE is not set
# CONFIG_BSD_PROCESS_ACCT is not set
CONFIG_SYSCTL=y
# CONFIG_AUDIT is not set
CONFIG_HOTPLUG=y
CONFIG_KOBJECT_UEVENT=y
# CONFIG_IKCONFIG is not set
CONFIG_INITRAMFS_SOURCE=""
# CONFIG_EMBEDDED is not set
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SHMEM=y
CONFIG_CC_ALIGN_FUNCTIONS=0
CONFIG_CC_ALIGN_LABELS=0
CONFIG_CC_ALIGN_LOOPS=0
CONFIG_CC_ALIGN_JUMPS=0
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_MODULE_FORCE_UNLOAD is not set
CONFIG_OBSOLETE_MODPARM=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_KMOD=y
#
# System Type
#
# CONFIG_ARCH_CLPS7500 is not set
# CONFIG_ARCH_CLPS711X is not set
# CONFIG_ARCH_CO285 is not set
# CONFIG_ARCH_EBSA110 is not set
# CONFIG_ARCH_CAMELOT is not set
# CONFIG_ARCH_FOOTBRIDGE is not set
# CONFIG_ARCH_INTEGRATOR is not set
# CONFIG_ARCH_IOP3XX is not set
# CONFIG_ARCH_IXP4XX is not set
# CONFIG_ARCH_IXP2000 is not set
# CONFIG_ARCH_L7200 is not set
# CONFIG_ARCH_PXA is not set
# CONFIG_ARCH_RPC is not set
# CONFIG_ARCH_SA1100 is not set
CONFIG_ARCH_S3C2410=y
# CONFIG_ARCH_SHARK is not set
# CONFIG_ARCH_LH7A40X is not set
# CONFIG_ARCH_OMAP is not set
# CONFIG_ARCH_VERSATILE is not set
# CONFIG_ARCH_IMX is not set
# CONFIG_ARCH_H720X is not set
# CONFIG_ARCH_AAEC2000 is not set
#
# S3C24XX Implementations
#
# CONFIG_MACH_ANUBIS is not set
# CONFIG_ARCH_BAST is not set
# CONFIG_ARCH_H1940 is not set
# CONFIG_MACH_N30 is not set
CONFIG_ARCH_SMDK2410=y
# CONFIG_ARCH_S3C2440 is not set
# CONFIG_MACH_VR1000 is not set
# CONFIG_MACH_RX3715 is not set
# CONFIG_MACH_OTOM is not set
# CONFIG_MACH_NEXCODER_2440 is not set
CONFIG_CPU_S3C2410=y
#
# S3C2410 Boot
#
#
# S3C2410 Setup
#
CONFIG_S3C2410_DMA=y
# CONFIG_S3C2410_DMA_DEBUG is not set
CONFIG_S3C2410_LOWLEVEL_UART_PORT=0
#
# Processor Type
#
CONFIG_CPU_32=y
CONFIG_CPU_ARM920T=y
CONFIG_CPU_32v4=y
CONFIG_CPU_ABRT_EV4T=y
CONFIG_CPU_CACHE_V4WT=y
CONFIG_CPU_CACHE_VIVT=y
CONFIG_CPU_COPY_V4WB=y
CONFIG_CPU_TLB_V4WBI=y
#
# Processor Features
#
CONFIG_ARM_THUMB=y
# CONFIG_CPU_ICACHE_DISABLE is not set
# CONFIG_CPU_DCACHE_DISABLE is not set
# CONFIG_CPU_DCACHE_WRITETHROUGH is not set
#
# Bus support
#
CONFIG_ISA=y
CONFIG_ISA_DMA_API=y
#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set
#
# Kernel Features
#
# CONFIG_PREEMPT is not set
# CONFIG_NO_IDLE_HZ is not set
# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
# CONFIG_SPARSEMEM_STATIC is not set
CONFIG_ALIGNMENT_TRAP=y
#
# Boot options
#
CONFIG_ZBOOT_ROM_TEXT=0x0
CONFIG_ZBOOT_ROM_BSS=0x0
CONFIG_CMDLINE="noinitrd root=/dev/mtdblock3 init=/linuxrc console=ttySAC0,115200"
# CONFIG_XIP_KERNEL is not set
#
# Floating point emulation
#
#
# At least one emulation must be selected
#
CONFIG_FPE_NWFPE=y
# CONFIG_FPE_NWFPE_XP is not set
# CONFIG_FPE_FASTFPE is not set
#
# Userspace binary formats
#
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_AOUT=y
# CONFIG_BINFMT_MISC is not set
# CONFIG_ARTHUR is not set
#
# Power management options
#
# CONFIG_PM is not set
#
# Networking
#
CONFIG_NET=y
#
# Networking options
#
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
CONFIG_UNIX=y
# CONFIG_NET_KEY is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_FIB_HASH=y
CONFIG_IP_PNP=y
# CONFIG_IP_PNP_DHCP is not set
CONFIG_IP_PNP_BOOTP=y
# CONFIG_IP_PNP_RARP is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_IP_MROUTE is not set
# CONFIG_ARPD is not set
# CONFIG_SYN_COOKIES is not set
# CONFIG_INET_AH is not set
# CONFIG_INET_ESP is not set
# CONFIG_INET_IPCOMP is not set
# CONFIG_INET_TUNNEL is not set
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_BIC=y
# CONFIG_IPV6 is not set
# CONFIG_NETFILTER is not set
#
# DCCP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_DCCP is not set
#
# SCTP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_SCTP is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_NET_SCHED is not set
# CONFIG_NET_CLS_ROUTE is not set
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_IEEE80211 is not set
#
# Device Drivers
#
#
# Generic Driver Options
#
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
# CONFIG_DEBUG_DRIVER is not set
#
# Memory Technology Devices (MTD)
#
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
# CONFIG_MTD_CONCAT is not set
CONFIG_MTD_PARTITIONS=y
# CONFIG_MTD_REDBOOT_PARTS is not set
# CONFIG_MTD_CMDLINE_PARTS is not set
# CONFIG_MTD_AFS_PARTS is not set
#
# User Modules And Translation Layers
#
CONFIG_MTD_CHAR=y
CONFIG_MTD_BLOCK=y
# CONFIG_FTL is not set
# CONFIG_NFTL is not set
# CONFIG_INFTL is not set
#
# RAM/ROM/Flash chip drivers
#
CONFIG_MTD_CFI=y
# CONFIG_MTD_JEDECPROBE is not set
CONFIG_MTD_GEN_PROBE=y
# CONFIG_MTD_CFI_ADV_OPTIONS is not set
CONFIG_MTD_MAP_BANK_WIDTH_1=y
CONFIG_MTD_MAP_BANK_WIDTH_2=y
CONFIG_MTD_MAP_BANK_WIDTH_4=y
# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
CONFIG_MTD_CFI_I1=y
CONFIG_MTD_CFI_I2=y
# CONFIG_MTD_CFI_I4 is not set
# CONFIG_MTD_CFI_I8 is not set
CONFIG_MTD_CFI_INTELEXT=y
# CONFIG_MTD_CFI_AMDSTD is not set
CONFIG_MTD_CFI_STAA=y
CONFIG_MTD_CFI_UTIL=y
# CONFIG_MTD_RAM is not set
# CONFIG_MTD_ROM is not set
# CONFIG_MTD_ABSENT is not set
# CONFIG_MTD_XIP is not set
#
# Mapping drivers for chip access
#
# CONFIG_MTD_COMPLEX_MAPPINGS is not set
# CONFIG_MTD_PHYSMAP is not set
# CONFIG_MTD_ARM_INTEGRATOR is not set
# CONFIG_MTD_EDB7312 is not set
# CONFIG_MTD_PLATRAM is not set
#
# Self-contained MTD device drivers
#
# CONFIG_MTD_SLRAM is not set
# CONFIG_MTD_PHRAM is not set
# CONFIG_MTD_MTDRAM is not set
# CONFIG_MTD_BLKMTD is not set
# CONFIG_MTD_BLOCK2MTD is not set
#
# Disk-On-Chip Device Drivers
#
# CONFIG_MTD_DOC2000 is not set
# CONFIG_MTD_DOC2001 is not set
# CONFIG_MTD_DOC2001PLUS is not set
#
# NAND Flash Device Drivers
#
CONFIG_MTD_NAND=y
# CONFIG_MTD_NAND_VERIFY_WRITE is not set
CONFIG_MTD_NAND_IDS=y
CONFIG_MTD_NAND_S3C2410=y
# CONFIG_MTD_NAND_S3C2410_DEBUG is not set
# CONFIG_MTD_NAND_S3C2410_HWECC is not set
# CONFIG_MTD_NAND_DISKONCHIP is not set
# CONFIG_MTD_NAND_NANDSIM is not set
#
# Parallel port support
#
CONFIG_PARPORT=y
# CONFIG_PARPORT_PC is not set
# CONFIG_PARPORT_ARC is not set
# CONFIG_PARPORT_GSC is not set
# CONFIG_PARPORT_1284 is not set
#
# Plug and Play support
#
CONFIG_PNP=y
# CONFIG_PNP_DEBUG is not set
#
# Protocols
#
# CONFIG_ISAPNP is not set
#
# Block devices
#
# CONFIG_BLK_DEV_XD is not set
# CONFIG_PARIDE is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
# CONFIG_BLK_DEV_LOOP is not set
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_UB is not set
# CONFIG_BLK_DEV_RAM is not set
CONFIG_BLK_DEV_RAM_COUNT=16
# CONFIG_CDROM_PKTCDVD is not set
#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
# CONFIG_ATA_OVER_ETH is not set
#
# ATA/ATAPI/MFM/RLL support
#
# CONFIG_IDE is not set
#
# SCSI device support
#
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
CONFIG_SCSI_PROC_FS=y
#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
# CONFIG_BLK_DEV_SR is not set
CONFIG_CHR_DEV_SG=y
# CONFIG_CHR_DEV_SCH is not set
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
CONFIG_SCSI_MULTI_LUN=y
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
#
# SCSI Transport Attributes
#
# CONFIG_SCSI_SPI_ATTRS is not set
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_ISCSI_ATTRS is not set
# CONFIG_SCSI_SAS_ATTRS is not set
#
# SCSI low-level drivers
#
# CONFIG_SCSI_7000FASST is not set
# CONFIG_SCSI_AHA152X is not set
# CONFIG_SCSI_AHA1542 is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_IN2000 is not set
# CONFIG_SCSI_SATA is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_DTC3280 is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_GENERIC_NCR5380 is not set
# CONFIG_SCSI_GENERIC_NCR5380_MMIO is not set
# CONFIG_SCSI_PPA is not set
# CONFIG_SCSI_IMM is not set
# CONFIG_SCSI_NCR53C406A is not set
# CONFIG_SCSI_PAS16 is not set
# CONFIG_SCSI_PSI240I is not set
# CONFIG_SCSI_QLOGIC_FAS is not set
# CONFIG_SCSI_SYM53C416 is not set
# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_U14_34F is not set
# CONFIG_SCSI_DEBUG is not set
#
# Multi-device support (RAID and LVM)
#
# CONFIG_MD is not set
#
# Fusion MPT device support
#
# CONFIG_FUSION is not set
#
# IEEE 1394 (FireWire) support
#
#
# I2O device support
#
#
# Network device support
#
CONFIG_NETDEVICES=y
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
# CONFIG_NET_SB1000 is not set
#
# ARCnet devices
#
# CONFIG_ARCNET is not set
#
# PHY device support
#
# CONFIG_PHYLIB is not set
#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
# CONFIG_MII is not set
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_LANCE is not set
# CONFIG_NET_VENDOR_SMC is not set
# CONFIG_SMC91X is not set
# CONFIG_DM9000 is not set
# CONFIG_NET_VENDOR_RACAL is not set
# CONFIG_AT1700 is not set
# CONFIG_DEPCA is not set
# CONFIG_HP100 is not set
CONFIG_NET_ISA=y
# CONFIG_E2100 is not set
# CONFIG_EWRK3 is not set
# CONFIG_EEXPRESS is not set
# CONFIG_EEXPRESS_PRO is not set
# CONFIG_HPLAN_PLUS is not set
# CONFIG_HPLAN is not set
# CONFIG_LP486E is not set
# CONFIG_ETH16I is not set
CONFIG_NE2000=y
# CONFIG_ZNET is not set
# CONFIG_SEEQ8005 is not set
# CONFIG_NET_PCI is not set
# CONFIG_NET_POCKET is not set
#
# Ethernet (1000 Mbit)
#
#
# Ethernet (10000 Mbit)
#
#
# Token Ring devices
#
# CONFIG_TR is not set
#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set
#
# Wan interfaces
#
# CONFIG_WAN is not set
# CONFIG_PLIP is not set
CONFIG_PPP=y
CONFIG_PPP_MULTILINK=y
# CONFIG_PPP_FILTER is not set
CONFIG_PPP_ASYNC=y
CONFIG_PPP_SYNC_TTY=y
# CONFIG_PPP_DEFLATE is not set
# CONFIG_PPP_BSDCOMP is not set
CONFIG_PPPOE=y
# CONFIG_SLIP is not set
# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
#
# ISDN subsystem
#
# CONFIG_ISDN is not set
#
# Input device support
#
CONFIG_INPUT=y
#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=640
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=480
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_TSDEV is not set
# CONFIG_INPUT_EVDEV is not set
# CONFIG_INPUT_EVBUG is not set
#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
# CONFIG_MOUSE_SERIAL is not set
# CONFIG_MOUSE_INPORT is not set
# CONFIG_MOUSE_LOGIBM is not set
# CONFIG_MOUSE_PC110PAD is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set
#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_SERIO_SERPORT=y
# CONFIG_SERIO_PARKBD is not set
CONFIG_SERIO_LIBPS2=y
# CONFIG_SERIO_RAW is not set
# CONFIG_GAMEPORT is not set
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_SERIAL_NONSTANDARD is not set
#
# Serial drivers
#
# CONFIG_SERIAL_8250 is not set
#
# Non-8250 serial port support
#
CONFIG_SERIAL_S3C2410=y
CONFIG_SERIAL_S3C2410_CONSOLE=y
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
# CONFIG_PRINTER is not set
# CONFIG_PPDEV is not set
# CONFIG_TIPAR is not set
#
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
# CONFIG_NVRAM is not set
# CONFIG_RTC is not set
CONFIG_S3C2410_RTC=y
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
#
# Ftape, the floppy tape device driver
#
# CONFIG_RAW_DRIVER is not set
#
# TPM devices
#
#
# I2C support
#
# CONFIG_I2C is not set
#
# Hardware Monitoring support
#
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
# CONFIG_HWMON_DEBUG_CHIP is not set
#
# Misc devices
#
#
# Multimedia Capabilities Port drivers
#
#
# Multimedia devices
#
CONFIG_VIDEO_DEV=y
#
# Video For Linux
#
#
# Video Adapters
#
# CONFIG_VIDEO_PMS is not set
# CONFIG_VIDEO_BWQCAM is not set
# CONFIG_VIDEO_CQCAM is not set
# CONFIG_VIDEO_CPIA is not set
#
# Radio Adapters
#
# CONFIG_RADIO_CADET is not set
# CONFIG_RADIO_RTRACK is not set
# CONFIG_RADIO_RTRACK2 is not set
# CONFIG_RADIO_AZTECH is not set
# CONFIG_RADIO_GEMTEK is not set
# CONFIG_RADIO_MAESTRO is not set
# CONFIG_RADIO_SF16FMI is not set
# CONFIG_RADIO_SF16FMR2 is not set
# CONFIG_RADIO_TERRATEC is not set
# CONFIG_RADIO_TRUST is not set
# CONFIG_RADIO_TYPHOON is not set
# CONFIG_RADIO_ZOLTRIX is not set
#
# Digital Video Broadcasting Devices
#
# CONFIG_DVB is not set
#
# Graphics support
#
CONFIG_FB=y
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
CONFIG_FB_SOFT_CURSOR=y
# CONFIG_FB_MACMODES is not set
# CONFIG_FB_MODE_HELPERS is not set
# CONFIG_FB_TILEBLITTING is not set
# CONFIG_FB_S1D13XXX is not set
CONFIG_FB_S3C2410=y
CONFIG_FB_S3C2410_DEBUG=y
# CONFIG_FB_VIRTUAL is not set
#
# Console display driver support
#
# CONFIG_VGA_CONSOLE is not set
# CONFIG_MDA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_FONTS=y
CONFIG_FONT_8x8=y
# CONFIG_FONT_8x16 is not set
# CONFIG_FONT_6x11 is not set
# CONFIG_FONT_7x14 is not set
# CONFIG_FONT_PEARL_8x8 is not set
# CONFIG_FONT_ACORN_8x8 is not set
# CONFIG_FONT_MINI_4x6 is not set
# CONFIG_FONT_SUN8x16 is not set
# CONFIG_FONT_SUN12x22 is not set
# CONFIG_FONT_10x18 is not set
#
# Logo configuration
#
CONFIG_LOGO=y
CONFIG_LOGO_LINUX_MONO=y
CONFIG_LOGO_LINUX_VGA16=y
CONFIG_LOGO_LINUX_CLUT224=y
CONFIG_BACKLIGHT_LCD_SUPPORT=y
CONFIG_BACKLIGHT_CLASS_DEVICE=y
CONFIG_BACKLIGHT_DEVICE=y
CONFIG_LCD_CLASS_DEVICE=y
CONFIG_LCD_DEVICE=y
#
# Sound
#
# CONFIG_SOUND is not set
#
# USB support
#
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set
#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_BANDWIDTH is not set
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_OTG is not set
#
# USB Host Controller Drivers
#
# CONFIG_USB_ISP116X_HCD is not set
CONFIG_USB_OHCI_HCD=y
# CONFIG_USB_OHCI_BIG_ENDIAN is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
# CONFIG_USB_SL811_HCD is not set
#
# USB Device Class drivers
#
# CONFIG_USB_BLUETOOTH_TTY is not set
# CONFIG_USB_ACM is not set
# CONFIG_USB_PRINTER is not set
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' may also be needed; see USB_STORAGE Help for more information
#
CONFIG_USB_STORAGE=y
# CONFIG_USB_STORAGE_DEBUG is not set
CONFIG_USB_STORAGE_DATAFAB=y
CONFIG_USB_STORAGE_FREECOM=y
CONFIG_USB_STORAGE_DPCM=y
CONFIG_USB_STORAGE_USBAT=y
CONFIG_USB_STORAGE_SDDR09=y
CONFIG_USB_STORAGE_SDDR55=y
CONFIG_USB_STORAGE_JUMPSHOT=y
#
# USB Input Devices
#
# CONFIG_USB_HID is not set
#
# USB HID Boot Protocol drivers
#
# CONFIG_USB_KBD is not set
# CONFIG_USB_MOUSE is not set
# CONFIG_USB_AIPTEK is not set
# CONFIG_USB_WACOM is not set
# CONFIG_USB_ACECAD is not set
# CONFIG_USB_KBTAB is not set
# CONFIG_USB_POWERMATE is not set
# CONFIG_USB_MTOUCH is not set
# CONFIG_USB_ITMTOUCH is not set
# CONFIG_USB_EGALAX is not set
# CONFIG_USB_YEALINK is not set
# CONFIG_USB_XPAD is not set
# CONFIG_USB_ATI_REMOTE is not set
# CONFIG_USB_KEYSPAN_REMOTE is not set
# CONFIG_USB_APPLETOUCH is not set
#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set
#
# USB Multimedia devices
#
# CONFIG_USB_DABUSB is not set
# CONFIG_USB_VICAM is not set
# CONFIG_USB_DSBR is not set
# CONFIG_USB_IBMCAM is not set
# CONFIG_USB_KONICAWC is not set
# CONFIG_USB_OV511 is not set
# CONFIG_USB_SE401 is not set
# CONFIG_USB_SN9C102 is not set
# CONFIG_USB_STV680 is not set
# CONFIG_USB_PWC is not set
#
# USB Network Adapters
#
# CONFIG_USB_CATC is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_USBNET is not set
CONFIG_USB_MON=y
#
# USB port drivers
#
# CONFIG_USB_USS720 is not set
#
# USB Serial Converter support
#
# CONFIG_USB_SERIAL is not set
#
# USB Miscellaneous drivers
#
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_PHIDGETKIT is not set
# CONFIG_USB_PHIDGETSERVO is not set
# CONFIG_USB_IDMOUSE is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TEST is not set
#
# USB DSL modem support
#
#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
#
# MMC/SD Card support
#
# CONFIG_MMC is not set
#
# File systems
#
# CONFIG_EXT2_FS is not set
# CONFIG_EXT3_FS is not set
# CONFIG_JBD is not set
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
# CONFIG_MINIX_FS is not set
CONFIG_ROMFS_FS=y
CONFIG_INOTIFY=y
# CONFIG_QUOTA is not set
CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
CONFIG_AUTOFS4_FS=y
# CONFIG_FUSE_FS is not set
#
# CD-ROM/DVD Filesystems
#
# CONFIG_ISO9660_FS is not set
# CONFIG_UDF_FS is not set
#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
# CONFIG_NTFS_FS is not set
#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
# CONFIG_RELAYFS_FS is not set
CONFIG_DEVFS_FS=y
CONFIG_DEVFS_MOUNT=y
#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
CONFIG_YAFFS_FS=y
CONFIG_YAFFS_YAFFS1=y
# CONFIG_YAFFS_9BYTE_TAGS is not set
CONFIG_YAFFS_DOES_ECC=y
# CONFIG_YAFFS_ECC_WRONG_ORDER is not set
CONFIG_YAFFS_YAFFS2=y
CONFIG_YAFFS_AUTO_YAFFS2=y
CONFIG_YAFFS_DISABLE_LAZY_LOAD=y
CONFIG_YAFFS_CHECKPOINT_RESERVED_BLOCKS=10
CONFIG_YAFFS_DISABLE_WIDE_TNODES=y
CONFIG_YAFFS_ALWAYS_CHECK_CHUNK_ERASED=y
CONFIG_YAFFS_SHORT_NAMES_IN_RAM=y
# CONFIG_JFFS_FS is not set
# CONFIG_JFFS2_FS is not set
CONFIG_CRAMFS=y
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
#
# Network File Systems
#
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
# CONFIG_NFS_V4 is not set
# CONFIG_NFS_DIRECTIO is not set
# CONFIG_NFSD is not set
CONFIG_ROOT_NFS=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
# CONFIG_9P_FS is not set
#
# Partition Types
#
CONFIG_PARTITION_ADVANCED=y
# CONFIG_ACORN_PARTITION is not set
# CONFIG_OSF_PARTITION is not set
# CONFIG_AMIGA_PARTITION is not set
# CONFIG_ATARI_PARTITION is not set
# CONFIG_MAC_PARTITION is not set
CONFIG_MSDOS_PARTITION=y
# CONFIG_BSD_DISKLABEL is not set
# CONFIG_MINIX_SUBPARTITION is not set
# CONFIG_SOLARIS_X86_PARTITION is not set
# CONFIG_UNIXWARE_DISKLABEL is not set
# CONFIG_LDM_PARTITION is not set
# CONFIG_SGI_PARTITION is not set
# CONFIG_ULTRIX_PARTITION is not set
# CONFIG_SUN_PARTITION is not set
# CONFIG_EFI_PARTITION is not set
#
# Native Language Support
#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=y
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
# CONFIG_NLS_CODEPAGE_850 is not set
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
CONFIG_NLS_CODEPAGE_936=y
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
# CONFIG_NLS_ASCII is not set
CONFIG_NLS_ISO8859_1=y
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
# CONFIG_NLS_ISO8859_15 is not set
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
# CONFIG_NLS_UTF8 is not set
#
# Profiling support
#
# CONFIG_PROFILING is not set
#
# Kernel hacking
#
# CONFIG_PRINTK_TIME is not set
CONFIG_DEBUG_KERNEL=y
# CONFIG_MAGIC_SYSRQ is not set
CONFIG_LOG_BUF_SHIFT=14
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_KOBJECT is not set
CONFIG_DEBUG_BUGVERBOSE=y
# CONFIG_DEBUG_INFO is not set
# CONFIG_DEBUG_FS is not set
CONFIG_FRAME_POINTER=y
CONFIG_DEBUG_USER=y
# CONFIG_DEBUG_WAITQ is not set
# CONFIG_DEBUG_ERRORS is not set
CONFIG_DEBUG_LL=y
# CONFIG_DEBUG_ICEDCC is not set
CONFIG_DEBUG_S3C2410_PORT=y
CONFIG_DEBUG_S3C2410_UART=0
#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
#
# Cryptographic options
#
# CONFIG_CRYPTO is not set
#
# Hardware crypto devices
#
#
# Library routines
#
CONFIG_CRC_CCITT=y
# CONFIG_CRC16 is not set
CONFIG_CRC32=y
CONFIG_LIBCRC32C=y
CONFIG_ZLIB_INFLATE=y