用vmware7.1.4安装fedora15的时候,没有出现分区配置的步骤,以为是fedora的问题呢,后来用vmware6.5重新安装,可出现分区配置步骤--
原来vmware7.1.4执行了默认配置--
如果不让vmware7.1.4默认安装,需要
在新建虚拟机那个步骤中一项稍后...选中
这样fedora就不会自动安装了
然后再为这个虚拟机添加iso文件,再启动就可以了
我配置的一个分区,记录一下以备日后参考
安装完成后则为
[root@localhost ~]# fdisk -l /dev/sda Disk /dev/sda: 42.9 GB, 42949672960 bytes 255 heads, 63 sectors/track, 5221 cylinders, total 83886080 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000d1cc8 Device Boot Start End Blocks Id System /dev/sda1 * 2048 1026047 512000 83 Linux /dev/sda2 1026048 68610047 33792000 83 Linux /dev/sda3 68610048 76998655 4194304 82 Linux swap / Solaris /dev/sda4 76998656 83886079 3443712 5 Extended /dev/sda5 77002752 79099903 1048576 8e Linux LVM /dev/sda6 79101952 80125951 512000 8e Linux LVM /dev/sda7 80128000 83886079 1879040 8e Linux LVM
[root@localhost ~]# df -m Filesystem 1M-blocks Used Available Use% Mounted on rootfs 32482 9271 21562 31% / udev 494 0 494 0% /dev tmpfs 502 1 502 1% /dev/shm tmpfs 502 1 501 1% /run /dev/sda2 32482 9271 21562 31% / tmpfs 502 0 502 0% /sys/fs/cgroup tmpfs 502 0 502 0% /media /dev/sda1 485 66 394 15% /boot /dev/mapper/VolGroup-LogVol00 1449 435 942 32% /tmp /dev/mapper/VolGroup-LogVol00 1449 435 942 32% /tmp /dev/sda2 32482 9271 21562 31% /var/tmp /dev/sda2 32482 9271 21562 31% /home /dev/sr0 3482 3482 0 100% /media/Fedora 15 i386 DVD
[root@localhost vmware-tools-distrib]# cat /etc/sysconfig/network-scripts/ifcfg-p3p1 DEVICE="p3p1" HWADDR="00:0C:29:55:3C:94" ONBOOT="yes" NM_CONTROLLED="yes" IPADDR=192.168.1.116 NETMASK=255.255.255.0 DNS1=61.139.2.69 DNS2=218.6.200.139 IPV6INIT=yes MTU=1500 GATEWAY=192.168.1.1再执行
fedora15的vmare tools竟然没有自动安装上
只有手动安装了
yum -y update
...
yum install gcc make kernel-devel perl kernel-PAE-devel
...
reboot
...
解压vmare tools到某个文件夹,如
执行
./vmware-install.pl
一路回车,重启或注销一下即可
refer to
http://www.patrulestheworld.com/?p=161
one website
http://wiki.xensource.com/xenwiki/Fedora13Xen4Tutorial