linux下显示网卡设备及驱动信息intel shell脚本

intel 发布的, 需具备有lspci 及ethtool 两个命令. 用户查看网卡信息非常方便

#! /bin/bash

#******************************************************************************
# Copyright(c) 1999 - 2008 Intel Corporation.
#
# This program is free software; you can redistribute it and/or modify it
# under the terms and conditions of the GNU General Public License,
# version 2, as published by the Free Software Foundation.
#
# This program is distributed in the hope it will be useful, but WITHOUT
# ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
# FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
# more details.
#
# You should have received a copy of the GNU General Public License along with
# this program; if not, write to the Free Software Foundation, Inc.,
# 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
#
# Contact Information:
# Linux NICS <[email protected]>
# Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
#******************************************************************************

#Determine how many Ethernet & Network controllers are installed in the system
TotalControllers=`lspci | grep -c -i 'Ethernet Controller\|Network Controller'`

temp=`lspci | grep -i 'Ethernet Controller\|Network Controller'|cut -f1 -d " "`

#Define two arrays for storing IPPorts
declare -a IOPorts1
declare -a IOPorts2

#Populate IOPorts1 with bus info from lspci. Populate IoPorts2 with bus info
#from ethtool.

for (( counter=0 ; counter < $TotalControllers ; counter++ ))
        do
                offset=$(($counter+1))
                IOPorts1[$counter]=`echo $temp|cut -f$offset -d" "`
                if (ethtool -i eth$counter) &> /dev/null; then
                        IOPorts2[$counter]=`ethtool -i eth$counter|grep 'bus-info'|cut -f3- -d :`
                fi
        done

#Loop through both arrays and determine if there's a match in IOPort1 & IOPort2. If so
#then the driver is loaded, and write to screen all the related information. If there
#is no match then there isn't a driver loaded for that device and write to screen only
#the information available from lspci

for ((counter=0 ; counter < $TotalControllers ; counter++))
        do
                Match=0
                for ((counter1=0 ; counter1 < $TotalControllers; counter1++))
                        do              
                                if [ "${IOPorts1[$counter]}" = "${IOPorts2[$counter1]}" ]; then
                                        Match=1                                 
                                        DeviceID=`lspci -nn | grep ${IOPorts2[$counter1]} |cut -f3- -d"["| cut -c 1-9`
                                        EthernetController=`lspci -v |grep ${IOPorts2[$counter1]} | cut -f4- -d" "|cut -f1 -d"("`
                                        AdapterName=`lspci -v | grep ${IOPorts2[$counter1]} -A 1 | grep 'Subsystem'|cut -f2- -d" "`
                                        DriverName=`ethtool -i eth$counter1 | grep -i 'driver' | cut -f2 -d" "`
                                        DriverVersion=`ethtool -i eth$counter1 | grep -m 1 -i 'version'| cut -f2 -d" "`
                                        echo "eth$counter1 : ${IOPorts2[$counter1]}"
                                        echo " Make/Model = $AdapterName"
                                        echo " Ethernet controller = $EthernetController"
                                        echo " VenID:DevID = $DeviceID"
                                        echo " Driver name = $DriverName"
                                        echo " Driver version = $DriverVersion"
                                fi
                        done
                if [ "$Match" = "0" ] ; then
                        DeviceID=`lspci -nn | grep ${IOPorts1[$counter]} |cut -f3- -d"["| cut -c 1-9`
                        EthernetController=`lspci -v |grep ${IOPorts1[$counter]} | cut -f4- -d" "|cut -f1 -d"("`
                        AdapterName=`lspci -v | grep ${IOPorts1[$counter]} -A 1 | grep 'Subsystem'|cut -f2- -d" "`
                        echo ": ${IOPorts1[$counter]}"
                        echo " Make/Model = $AdapterName"
                        echo " Ethernet controller = $EthernetController"
                        echo " VenID:DevID = $DeviceID"
                        echo " Driver name = No driver loaded"
                        echo " Driver version = No driver loaded"
                fi
        done
exit 0