阅读更多
title Ubuntu, kernel 2.6.15-23-386
root (hd0,1)
kernel /boot/vmlinuz-2.6.15-23-386 root=/dev/hdb2 ro quiet splash
initrd /boot/initrd.img-2.6.15-23-386
savedefault
boot
title Ubuntu, kernel 2.6.15-23-386 (recovery mode)
root (hd0,1)
kernel /boot/vmlinuz-2.6.15-23-386 root=/dev/hdb2 ro single
initrd /boot/initrd.img-2.6.15-23-386
boot
title Ubuntu, memtest86+
root (hd0,1)
kernel /boot/memtest86+.bin
boot
title Slackware 12
rootnoverify (hd0,3)
kernel /boot/vmlinuz root=/dev/hdb4
# (0) Arch Linux
title Arch Linux
root (hd0,3)
kernel /boot/vmlinuz26 root=/dev/sda4 ro
initrd /boot/kernel26.img
# (1) Arch Linux
title Arch Linux Fallback
root (hd0,3)
kernel /boot/vmlinuz26 root=/dev/sda4 ro
initrd /boot/kernel26-fallback.img
title Gentoo 2007
kernel (hd0,4)/isolinux/gentoo root=/dev/ram0 init=/linuxrc dokeymap looptype=squashfs loop=/image.squashfs cdroot vga=791 splash=silent,theme:livecd-2007.0 CONSOLE=/dev/tty1 nox
initrd (hd0,4)/isolinux/gentoo.igz
title ArchLinux Install
kernel (hd0,4)/boot/vmlinuz
initrd (hd0,4)/boot/initrd.img
title Install Slackware
kernel (hd0,4)/slkboot/bzImage load_ramdisk=1 prompt_ramdisk=0 rw SLACK_KERNEL=huge.s
initrd (hd0,4)/slkboot/initrd.img
splashimage=(hd0,3)/boot/grub/splash.xpm.gz
title=Gentoo Linux
root (hd0,3)
kernel /boot/kernel-genkernel-x86-2.6.19-gentoo-r5 root=/dev/ram0 init=/linuxrc ramdisk=8192 real_root=/dev/hdb4
initrd /boot/initramfs-genkernel-x86-2.6.19-gentoo-r5
default 0
timeout 30
splashimage=(hd0,0)/boot/grub/splash.xpm.gz
title=Gentoo Linux 2.6.19-r5
root (hd0,0)
kernel /boot/kernel-genkernel-x86-2.6.19-gentoo-r5 root=/dev/ram0 init=/linuxrc ramdisk=8192 real_root=/dev/hda3 udev
initrd /boot/initramfs-genkernel-x86-2.6.19-gentoo-r5
# 只有在双启动的情况下才需要以下内容
title=Windows XP
rootnoverify (hd0,5)
makeactive
chainloader +1
# emerge grub
# nano -w /boot/grub/grub.conf
# grub-install /dev/hda
Device Boot Start End Blocks Id System
/dev/hda1 * 1 14 105808+ 83 Linux
/dev/hda2 15 81 506520 82 Linux swap
/dev/hda3 82 3876 28690200 83 Linux
# mke2fs /dev/hda1 ——以ext2文件系统格式化分区1
# mke2fs -j /dev/hda3 ——以ext3文件系统格式化分区3
# mkswap /dev/hda2 ——以linux swap文件系统格式化分区2
# swapon /dev/hda2 ——激活交换分区
1、Device Drivers-->SCSI device support-->SCSI low-level drivers-->BusLogic SCSI support（使用SCSI hard disk时必须）
2、File systems-->Reiserfs support（安装gentoo手册把/分区设为Reiserfs的话必须）
3、File systems-->DOS/FAT/NT Filesystems-->NTFS file system support（若要支持NTFS分区）
4、File systems-->Native Language Support-->Simplified Chinese charset (CP936, GB2312)（支持简体中文）
5、File systems-->Native Language Support-->Traditional Chinese charset (Big5)（支持繁体中文）
