1.修改主机名：
vim /etc/sysconfig/network
NETWORKING=yes
HOSTNAME=MASTER
2.修改IP：
vim /etc/sysconfig/network-scripts/ifcfg-eth0
BOOTPROTO="static"
HWADDR="00:0C:29:FC:62:B6"
IPV6INIT="yes"
NM_CONTROLLED="yes"
ONBOOT="yes"
TYPE="Ethernet"
UUID="d0731a46-36df-4ab1-9bac-42bb151acc41"
IPADDR="192.168.1.250"
NETMASK="255.255.255.0"
GATEWAY="192.168.1.1"
DNS1="8.8.8.8"
DNS2="8.8.4.4"
3.修改主机和IP的映射关系
vim /etc/hosts
127.0.0.1 localhost localhost.localdomain localhost4 localhost4.localdomain4
::1 localhost localhost.localdomain localhost6 localhost6.localdomain6
192.168.1.250 MASTER
192.168.1.251 SLAVE-1
192.168.1.252 SLAVE-2
4.关闭防火墙
vim /etc/sysconfig/selinux
# This file controls the state of SELinux on the system.
# SELINUX= can take one of these three values:
# enforcing - SELinux security policy is enforced.
# permissive - SELinux prints warnings instead of enforcing.
# disabled - No SELinux policy is loaded.
SELINUX=disabled
# SELINUXTYPE= can take one of these two values:
# targeted - Targeted processes are protected,
# mls - Multi Level Security protection.
SELINUXTYPE=targeted
继续执行命令：
service iptables stop
chkconfig iptables off
reboot
5.上传jdk安装包
6.解压安装
chmod +x jdk-6u45-linux-x64.bin
./jdk-6u45-linux-x64.bin
mkdir /usr/java
mv jdk1.6.0_45/ /usr/java/
7.配置环境变量
vim /etc/profile
在文件最后面添加：
export JAVA_HOME=/usr/java/jdk1.6.0_45
export CLASSPATH=$JAVA_HOME/lib
export PATH=$PATH:$JAVA_HOME/bin
更新配置：
source /etc/profile
上传zeromq-2.1.7.tar.gz、jzmq-master.zip、storm-0.8.2.zip、zookeeper-3.4.5.tar.gz等文件
1.编译安装ZMQ：
tar -xzf zeromq-2.1.7.tar.gz
cd zeromq-2.1.7
./configure
#编译可能会出错：configure: error: Unable to find a working C++ compiler
#安装一下依赖的rpm包：libstdc++-devel gcc-c++
可以上网的情况下：
yum install gcc-c++
虚拟机不能上网情况：首先到http://mirrors.163.com/centos/6.4/os/x86_64/Packages/ 下载rpm
rpm -i libstdc++-devel-4.4.7-3.el6.x86_64.rpm
rpm -i gcc-c++-4.4.7-3.el6.x86_64.rpm
rpm -i libuuid-devel-2.17.2-12.9.el6.x86_64.rpm
./configure
make
make install
2.编译安装JZMQ：
cd jzmq
./autogen.sh
#报错:autogen.sh: error: could not find libtool. libtool is required to run autogen.sh. 缺少libtool
yum install libtool
或者手动安装
rpm -i autoconf-2.63-5.1.el6.noarch.rpm
rpm -i automake-1.11.1-4.el6.noarch.rpm
rpm -i libtool-2.2.6-15.5.el6.x86_64.rpm
./configure
make
make install
storm启动
1、把storm的启动信息输出到指定文件
storm nimbus >/dev/null 2>&1 &
storm ui >/dev/null 2>&1 &
storm supervisor >/dev/null 2>&1 &
storm jar lify-cycle cn.*.TopoMain
storm jar storm-starter-0.0.1-SNAPSHOT-jar-with-dependencies.jar storm.starter.ExclamationTopology ExclamationTopology
storm jar storm-starter-0.0.1-SNAPSHOT-jar-with-dependencies.jar storm.starter.WordCountTopology WordCountTopology
storm jar storm-starter-0.0.1-SNAPSHOT-jar-with-dependencies.jar storm.starter.ReachTopology ReachTopology
storm jar WordCount.jar cn.itcast.storm.topology.WordCountTopo /home/mobileweb/hadoop/storm-starter-master/data 2
storm jar WordCount.jar cn.itcast.storm.topology.WordCountTopo /home/mobileweb/hadoop/storm-starter-master/data 2
java -jar WordCount.jar /home/mobileweb/hadoop/storm-starter-master/data 2