从维基百科里面转载的5种分组密码块反馈模式

网址：http://en.wikipedia.org/wiki/Block_cipher_modes_of_operation#Counter_.28CTR.29

Block cipher mode of operation

From Wikipedia, the free encyclopedia

  (Redirected from  Block cipher modes of operation)

This article is about cryptography. For "method of operating", see  modus operandi.

In cryptography, a mode of operation is an algorithm that uses a block cipher to provide an information service such as confidentiality orauthenticity.^[1] A block cipher by itself is only suitable for the secure cryptographic transformation (encryption or decryption) of one fixed-length group of bits called a block.^[2] A mode of operation describes how to repeatedly apply a cipher's single-block operation to securely transform amounts of data larger than a block.^[3][4][5]

Most modes require a unique binary sequence, often called an initialization vector (IV), for each encryption operation. The IV has to be non-repeating and for some modes random as well. The initialization vector is used to ensure distinct ciphertexts are produced even when the sameplaintext is encrypted multiple times independently with the same key.^[6] Block ciphers have one or more block size(s), but during transformation the block size is always fixed. Block cipher modes operate on whole blocks and require that the last part of the data be padded to a full block if it is smaller than the current block size.^[2] There are, however, modes that do not require padding because they effectively use a block cipher as astream cipher.

Historically, encryption modes have been studied extensively in regard to their error propagation properties under various scenarios of data modification. Later development regarded integrity protection as an entirely separate cryptographic goal. Some modern modes of operation combineconfidentiality and authenticity in an efficient way, and are known as authenticated encryption modes.^[7]

History and standardization[edit]

The earliest modes of operation, ECB, CBC, OFB, and CFB (see below for all), date back to 1981 and were specified in FIPS 81, DES Modes of Operation. In 2001, the US National Institute of Standards and Technology (NIST) revised its list of approved modes of operation by including AES as a block cipher and adding CTR mode in SP800-38A, Recommendation for Block Cipher Modes of Operation. Finally, in January, 2010, NIST added XTS-AES in SP800-38E, Recommendation for Block Cipher Modes of Operation: The XTS-AES Mode for Confidentiality on Storage Devices. Other confidentiality modes exist which have not been approved by NIST. For example, CTS is ciphertext stealing mode and available in many popular cryptographic libraries.

The block cipher modes ECB, CBC, OFB, CFB, CTR, and XTS provide confidentiality, but they do not protect against accidental modification or malicious tampering. Modification or tampering can be detected with a separate message authentication code such as CBC-MAC, or a digital signature. The cryptographic community recognized the need for dedicated integrity assurances and NIST responded with HMAC, CMAC, and GMAC. HMAC was approved in 2002 as FIPS 198, The Keyed-Hash Message Authentication Code (HMAC), CMAC was released in 2005 under SP800-38B, Recommendation for Block Cipher Modes of Operation: The CMAC Mode for Authentication, and GMAC was formalized in 2007 under SP800-38D, Recommendation for Block Cipher Modes of Operation: Galois/Counter Mode (GCM) and GMAC.

After observing that compositing a confidentiality mode with an authenticity mode could be difficult and error prone, the cryptographic community began to supply modes which combined confidentiality and data integrity into a single cryptographic primitive. The modes are referred to asauthenticated encryption, AE or "authenc". Examples of authenc modes are CCM (SP800-38C), GCM (SP800-38D), CWC, EAX, IAPM, and OCB.

Modes of operation are nowadays defined by a number of national and internationally recognized standards bodies. Notable standards organizations include NIST, ISO (with ISO/IEC 10116^[5]), the IEC, the IEEE, the national ANSI, and the IETF.

Initialization vector (IV)[edit]

Main article:  Initialization vector

An initialization vector (IV) or starting variable (SV)^[5] is a block of bits that is used by several modes to randomize the encryption and hence to produce distinct ciphertexts even if the same plaintext is encrypted multiple times, without the need for a slower re-keying process.^[6]

An initialization vector has different security requirements than a key, so the IV usually does not need to be secret. However, in most cases, it is important that an initialization vector is never reused under the same key. For CBC and CFB, reusing an IV leaks some information about the first block of plaintext, and about any common prefix shared by the two messages. For OFB and CTR, reusing an IV completely destroys security.^[6] This can be seen because both modes effectively create a bitstream that is XORed with the plaintext, and this bitstream is dependent on the password and IV only. Reusing a bitstream destroys security.^[8] In CBC mode, the IV must, in addition, be unpredictable at encryption time; in particular, the (previously) common practice of re-using the last ciphertext block of a message as the IV for the next message is insecure (for example, this method was used by SSL 2.0). If an attacker knows the IV (or the previous block of ciphertext) before he specifies the next plaintext, he can check his guess about plaintext of some block that was encrypted with the same key before (this is known as the TLS CBC IV attack).^[9]

Padding[edit]

Main article:  Padding (cryptography)

A block cipher works on units of a fixed size (known as a block size), but messages come in a variety of lengths. So some modes (namely ECB and CBC) require that the final block be padded before encryption. Several padding schemes exist. The simplest is to add null bytes to the plaintext to bring its length up to a multiple of the block size, but care must be taken that the original length of the plaintext can be recovered; this is so, for example, if the plaintext is a C style string which contains no null bytes except at the end. Slightly more complex is the original DES method, which is to add a single one bit, followed by enough zero bits to fill out the block; if the message ends on a block boundary, a whole padding block will be added. Most sophisticated are CBC-specific schemes such as ciphertext stealing or residual block termination, which do not cause any extra ciphertext, at the expense of some additional complexity. Schneier and Ferguson suggest two possibilities, both simple: append a byte with value 128 (hex 80), followed by as many zero bytes as needed to fill the last block, or pad the last block with n bytes all with value n.

CFB, OFB and CTR modes do not require any special measures to handle messages whose lengths are not multiples of the block size, since the modes work by XORing the plaintext with the output of the block cipher. The last partial block of plaintext is XORed with the first few bytes of the lastkeystream block, producing a final ciphertext block that is the same size as the final partial plaintext block. This characteristic of stream ciphers makes them suitable for applications that require the encrypted ciphertext data to be the same size as the original plaintext data, and for applications that transmit data in streaming form where it is inconvenient to add padding bytes.

Common modes[edit]

Many modes of operation have been defined. Some of these are described below.

Electronic codebook (ECB)[edit]

ECB
Electronic codebook
Encryption parallelizable:	Yes
Decryption parallelizable:	Yes

The simplest of the encryption modes is the electronic codebook (ECB) mode. The message is divided into blocks, and each block is encrypted separately.

The disadvantage of this method is that identical plaintext blocks are encrypted into identical ciphertext blocks; thus, it does not hide data patterns well. In some senses, it doesn't provide serious message confidentiality, and it is not recommended for use in cryptographic protocols at all.

A striking example of the degree to which ECB can leave plaintext data patterns in the ciphertext can be seen when ECB mode is used to encrypt abitmap image which uses large areas of uniform colour. While the colour of each individual pixel is encrypted, the overall image may still be discerned as the pattern of identically coloured pixels in the original remains in the encrypted version.

Original image

Encrypted using ECB mode

Modes other than ECB result in pseudo-randomness

The image on the right is how the image might appear encrypted with CBC, CTR or any of the other more secure modes—indistinguishable from random noise. Note that the random appearance of the image on the right does not ensure that the image has been securely encrypted; many kinds of insecure encryption have been developed which would produce output just as "random-looking".

ECB mode can also make protocols without integrity protection even more susceptible to replay attacks, since each block gets decrypted in exactly the same way.

Cipher-block chaining (CBC)[edit]

CBC
Cipher-block chaining
Encryption parallelizable:	No
Decryption parallelizable:	Yes

IBM invented the cipher-block chaining (CBC) mode of operation in 1976.^[10] In CBC mode, each block of plaintext is XORed with the previous ciphertext block before being encrypted. This way, each ciphertext block depends on all plaintext blocks processed up to that point. To make each message unique, aninitialization vector must be used in the first block.

If the first block has index 1, the mathematical formula for CBC encryption is

while the mathematical formula for CBC decryption is

CBC has been the most commonly used mode of operation. Its main drawbacks are that encryption is sequential (i.e., it cannot be parallelized), and that the message must be padded to a multiple of the cipher block size. One way to handle this last issue is through the method known as ciphertext stealing. Note that a one-bit change in a plaintext or IV affects all following ciphertext blocks.

Decrypting with the incorrect IV causes the first block of plaintext to be corrupt but subsequent plaintext blocks will be correct. This is because a plaintext block can be recovered from two adjacent blocks of ciphertext. As a consequence, decryption can be parallelized. Note that a one-bit change to the ciphertext causes complete corruption of the corresponding block of plaintext, and inverts the corresponding bit in the following block of plaintext, but the rest of the blocks remain intact.

Propagating cipher-block chaining (PCBC)[edit]

PCBC
Propagating cipher-block chaining
Encryption parallelizable:	No
Decryption parallelizable:	No

The propagating cipher-block chaining^[11] or plaintext cipher-block chaining^[12] mode was designed to cause small changes in the ciphertext to propagate indefinitely when decrypting, as well as when encrypting.

Encryption and decryption algorithms are as follows:

PCBC is used in Kerberos v4 and WASTE, most notably, but otherwise is not common. On a message encrypted in PCBC mode, if two adjacent ciphertext blocks are exchanged, this does not affect the decryption of subsequent blocks.^[13] For this reason, PCBC is not used in Kerberos v5.

Cipher feedback (CFB)[edit]

CFB
Cipher feedback
Encryption parallelizable:	No
Decryption parallelizable:	Yes

The cipher feedback (CFB) mode, a close relative of CBC, makes a block cipher into a self-synchronizingstream cipher. Operation is very similar; in particular, CFB decryption is almost identical to CBC encryption performed in reverse:

This simplest way of using CFB described above is not any more self-synchronizing than other cipher modes like CBC. If a whole blocksize of ciphertext is lost both CBC and CFB will synchronize, but losing only a single byte or bit will permanently throw off decryption. To be able to synchronize after the loss of only a single byte or bit, a single byte or bit must be encrypted at a time. CFB can be used this way when combined with a shift register as the input for the block cipher.

To use CFB to make a self-synchronizing stream cipher that will synchronize for any multiple of x bits lost, start by initializing a shift register the size of the block size with the initialization vector. This is encrypted with the block cipher, and the highest x bits of the result are XOR'ed with x bits of the plaintext to produce x bits of ciphertext. These x bits of output are shifted into the shift register, and the process repeats with the next x bits of plaintext. Decryption is similar, start with the initialization vector, encrypt, and XOR the high bits of the result with x bits of the ciphertext to produce x bits of plaintext. Then shift the x bits of the ciphertext into the shift register. This way of proceeding is known as CFB-8 or CFB-1 (according to the size of the shifting).^[14]

In notation, where S_i is the ith state of the shift register, a << x is a shifted up x bits, head(a, x) is the x highest bits of a and n is number of bits of IV:

If x bits are lost from the ciphertext, the cipher will output incorrect plaintext until the shift register once again equals a state it held while encrypting, at which point the cipher has resynchronized. This will result in at most one blocksize of output being garbled.

Like CBC mode, changes in the plaintext propagate forever in the ciphertext, and encryption cannot be parallelized. Also like CBC, decryption can be parallelized. When decrypting, a one-bit change in the ciphertext affects two plaintext blocks: a one-bit change in the corresponding plaintext block, and complete corruption of the following plaintext block. Later plaintext blocks are decrypted normally.

CFB shares two advantages over CBC mode with the stream cipher modes OFB and CTR: the block cipher is only ever used in the encrypting direction, and the message does not need to be padded to a multiple of the cipher block size (though ciphertext stealing can also be used to make padding unnecessary).

Output feedback (OFB)[edit]

OFB
Output feedback
Encryption parallelizable:	No
Decryption parallelizable:	No

The output feedback (OFB) mode makes a block cipher into a synchronous stream cipher. It generateskeystream blocks, which are then XORed with the plaintext blocks to get the ciphertext. Just as with other stream ciphers, flipping a bit in the ciphertext produces a flipped bit in the plaintext at the same location. This property allows many error correcting codes to function normally even when applied before encryption.

Because of the symmetry of the XOR operation, encryption and decryption are exactly the same:

Each output feedback block cipher operation depends on all previous ones, and so cannot be performed in parallel. However, because the plaintext or ciphertext is only used for the final XOR, the block cipher operations may be performed in advance, allowing the final step to be performed in parallel once the plaintext or ciphertext is available.

It is possible to obtain an OFB mode keystream by using CBC mode with a constant string of zeroes as input. This can be useful, because it allows the usage of fast hardware implementations of CBC mode for OFB mode encryption.

Using OFB mode with a partial block as feedback like CFB mode reduces the average cycle length by a factor of  or more. A mathematical model proposed by Davies and Parkin and substantiated by experimental results showed that only with full feedback an average cycle length near to the obtainable maximum can be achieved. For this reason, support for truncated feedback was removed from the specification of OFB.^[15][16]

Counter (CTR)[edit]

CTR
Counter
Encryption parallelizable:	Yes
Decryption parallelizable:	Yes

Note: CTR mode (CM) is also known as integer counter mode  (ICM) and segmented integer counter  (SIC) mode

Like OFB, counter mode turns a block cipher into a stream cipher. It generates the next keystream block by encrypting successive values of a "counter". The counter can be any function which produces a sequence which is guaranteed not to repeat for a long time, although an actual increment-by-one counter is the simplest and most popular. The usage of a simple deterministic input function used to be controversial; critics argued that "deliberately exposing a cryptosystem to a known systematic input represents an unnecessary risk."^[17] By now, CTR mode is widely accepted, and problems resulting from the input function are recognized as a weakness of the underlying block cipher instead of the CTR mode.^[18] Along with CBC, CTR mode is one of two block cipher modes recommended by Niels Ferguson and Bruce Schneier.^[19]

CTR mode has similar characteristics to OFB, but also allows a random access property during decryption. CTR mode is well suited to operate on a multi-processor machine where blocks can be encrypted in parallel. Furthermore, it does not suffer from the short-cycle problem that can affect OFB.^[20]

Note that the nonce in this diagram is the same thing as the initialization vector (IV) in the other diagrams. The IV/nonce and the counter can be combined together using any lossless operation (concatenation, addition, or XOR) to produce the actual unique counter block for encryption.

Error propagation[edit]

Before the widespread use of message authentication codes and authenticated encryption, it was common to discuss the "error propagation" properties as a selection criterion for a mode of operation. It might be observed, for example, that a one-block error in the transmitted ciphertext would result in a one-block error in the reconstructed plaintext for ECB mode encryption, while in CBC mode such an error would affect two blocks.

Some felt that such resilience was desirable in the face of random errors (e.g., line noise), while others argued that error correcting increased the scope for attackers to maliciously tamper with a message.

However, when proper integrity protection is used, such an error will result (with high probability) in the entire message being rejected. If resistance to random error is desirable, error-correcting codes should be applied to the ciphertext before transmission.

Authenticated encryption[edit]

Main article:  Authenticated encryption

A number of modes of operation have been designed to combine secrecy and authentication in a single cryptographic primitive. Examples of such modes are XCBC,^[21] IACBC, IAPM,^[22] OCB, EAX, CWC, CCM, and GCM. Authenticated encryption modes are classified as single pass modes or double pass modes. Unfortunately for the cryptographic user community, many of the single pass authenticated encryption algorithms (such as OCB mode) are patent encumbered.

In addition, some modes also allow for the authentication of unencrypted associated data, and these are called AEAD (Authenticated-Encryption with Associated-Data) schemes. For example, EAX mode is a double pass AEAD scheme while OCB mode is single pass.

Other modes and other cryptographic primitives[edit]

Many more modes of operation for block ciphers have been suggested. Some have been accepted, fully described (even standardized), and are in use. Others have been found insecure, and should never be used. Still others don't categorize as confidentiality, authenticity, or authenticated encryption - for example key feedback mode and Davies-Meyer hashing.

NIST maintains a list of proposed modes for block ciphers at Modes Development.^[14][23]

Disk encryption often uses special purpose modes specifically designed for the application. Tweakable narrow-block encryption modes (LRW, XEX, andXTS) and wide-block encryption modes (CMC and EME) are designed to securely encrypt sectors of a disk. (See disk encryption theory)

Block ciphers can also be used in other cryptographic protocols. They are generally used in modes of operation similar to the block modes described here. As with all protocols, to be cryptographically secure, care must be taken to build them correctly.

There are several schemes which use a block cipher to build a cryptographic hash function. See one-way compression function for descriptions of several such methods.

Cryptographically secure pseudorandom number generators (CSPRNGs) can also be built using block ciphers.

Message authentication codes (MACs) are often built from block ciphers. CBC-MAC, OMAC and PMAC are examples.

v t e   Block ciphers ( security summary) Common algorithms AES (Implementations) Blowfish DES (Internal Mechanics, Triple DES) Serpent Twofish   Less common algorithms Camellia CAST-128 IDEA RC2 RC5 SEED Skipjack TEA XTEA   Other algorithms 3-Way Akelarre Anubis ARIA BaseKing BassOmatic BATON BEAR and LION CAST-256 Chiasmus CIKS-1 CIPHERUNICORN-A CIPHERUNICORN-E CLEFIA CMEA Cobra COCONUT98 Crab Cryptomeria/C2 CRYPTON CS-Cipher DEAL DES-X DFC E2 FEAL FEA-M FROG G-DES GOST Grand Cru Hasty Pudding cipher Hierocrypt ICE IDEA NXT Intel Cascade Cipher Iraqi KASUMI KeeLoq KHAZAD Khufu and Khafre KN-Cipher Ladder-DES Libelle LOKI (97, 89/91) Lucifer M6 M8 MacGuffin Madryga MAGENTA MARS Mercy MESH MISTY1 MMB MULTI2 MultiSwap New Data Seal NewDES Nimbus NOEKEON NUSH PRESENT Q RC6 REDOC Red Pike S-1 SAFER SAVILLE SC2000 SHACAL SHARK Simon SMS4 Speck Spectr-H64 Square SXAL/MBAL Threefish Treyfer UES Xenon xmx XXTEA Zodiac   Design Feistel network Key schedule Lai-Massey scheme Product cipher S-box P-box SPN Avalanche effect Block size Key size Key whitening (Whitening transformation)   Attack (cryptanalysis) Brute-force (EFF DES cracker) MITM Linear (Piling-up lemma) Differential (Impossible Truncated Higher-order) Differential-linear Integral (aka Square) Boomerang Mod n Related-key Slide Rotational Timing XSL Interpolation Partitioning Davies' Rebound Biclique Weak key   Standardization AES process CRYPTREC NESSIE   Utilization Initialization vector Mode of operation Padding   v t e   Hash functions &  message authentication codes Security summary   Common functions MD5 SHA-1 SHA-2 SHA-3/Keccak   SHA-3 finalists BLAKE Grøstl JH Skein Keccak (winner)   Other functions FSB ECOH GOST HAS-160 HAVAL LM hash MDC-2 MD2 MD4 MD6 N-Hash RadioGatún RIPEMD RTR0 SipHash Snefru SWIFFT Tiger VSH WHIRLPOOL crypt(3) (DES)   MAC algorithms DAA CBC-MAC HMAC OMAC/CMAC PMAC VMAC UMAC Poly1305-AES   Authenticated encryption modes CCM CWC EAX GCM IAPM OCB   Attacks Collision attack Preimage attack Birthday attack Brute force attack Rainbow table Distinguishing attack Side-channel attack Length extension attack   Design Avalanche effect Hash collision Merkle–Damgård construction   Standardization CRYPTREC NESSIE NIST hash function competition   Utilization Salt Key stretching   v t e   Cryptography History of cryptography Cryptanalysis Cryptography portal Outline of cryptography   Symmetric-key algorithm Block cipher Stream cipher Public-key cryptography Cryptographic hash function Message authentication code Random numbers Steganography

Categories: 

• Block cipher modes of operation
• Cryptographic algorithms