cisco路由器基本实验之一 静态路由的配置（Boson NetSim）

        花了快一个月的时间之后，我的Linux服务器建设学习算是小告了一个段落了。现在开始要回到windows里面利用Boson NetSim这个cisco实验模拟器来加深对路由交换的配置学习了。好在上学期上课的时候学了一些路由器的知识，在实验室也做过一些实验，但大都比较简单，反正我觉得没学到什么高深的网络配置知识。趁着暑假，自己来做做模拟实验，也可以学到很多东西，今天是第一个比较简单的实验，但由于以前没涉及到某些方面，这样一个简单的实验还是花了我不少的时间的，呵呵，下面来看这个实验：

      如上的拓扑所示，（IP地址是我自己确定的，并且用ps写上的，这样看得比较清楚），现在需要完成的就是让HostA能和HostB互相ping通，我在配置过程中遇到了一些问题，我都把容易出错的地方注释在下面的配置语句后面了，希望那些跟我一样在网络配置方面还处于初步的朋友一些帮助，还希望高手们不要见笑，并且给我多加指教，先谢谢了，好了，看我的具体配置如下：

router1的配置：

 

Press Enter to Start

Router>
Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#hostname router1
router1(config)#interface e0
router1(config-if)#ip address 192.168.1.2 255.255.255.0
router1(config-if)#no shut
%LINK-3-UPDOWN: Interface Ethernet0, changed state to up
router1(config-if)#interface s0
router1(config-if)#ip address 192.168.2.1 255.255.255.0
router1(config-if)#clock rate 6400                   //clock rate是dce设备给dte设备提供时钟频率的，需要在dce里面设置，而另外的一个路由器里面则不用设置
router1(config-if)#no shut
%LINK-3-UPDOWN: Interface Serial0, changed state to up
router1(config-if)#end
%LINK-3-UPDOWN: Interface Serial0, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to down
router1#config t
Enter configuration commands, one per line.  End with CNTL/Z.
router1(config)#ip route 192.168.3.0 255.255.255.0 192.168.2.1   //设定静态路由
router1(config)#ip route 192.168.2.0 255.255.255.0 192.168.2.1
router1(config)#end
router1#copy running startup
Destination filename [startup-config]?
Building configuration...
[OK]

%LINK-3-UPDOWN: Interface Serial0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to up

 

router2的配置：

 

Press Enter to Start

Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#interface e0
Router(config-if)#end
Router#config t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#hostname router2
router2(config)#interface s0
router2(config-if)#ip address 192.168.2.2 255.255.255.0
router2(config-if)#no shut
%LINK-3-UPDOWN: Interface Serial0, changed state to up
router2(config-if)#interface s0
router2(config-if)#interface e0
router2(config-if)#ip address 192.168.3.1 255.255.255.0
router2(config-if)#no shut
%LINK-3-UPDOWN: Interface Ethernet0, changed state to up
router2(config-if)#end
router2#config t
Enter configuration commands, one per line.  End with CNTL/Z.
router2(config)#ip route 192.168.1.0 255.255.255.0 192.168.2.2
router2(config)#ip route 192.168.2.0 255.255.255.0 192.168.2.2
router2(config)#end
router2#copy running startup
Destination filename [startup-config]?
Building configuration...
[OK]

router2#ping 192.168.1.2

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms
router2#ping 192.168.2.1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.2.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms
router2#ping 192.168.2.2

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.2.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms       //路由器之间试ping了一下，可以ping通，接下来配pc

 

pc1的配置如下：

 

Boson BOSS 5.0
Copyright 1998-2003 Boson Software, Inc.
Use the command help to get started

Press Enter to begin
C:>ipconfig /ip 192.168.1.1 255.255.255.0                     //此时尚未指定网关
C:>ping 192.168.2.1
Pinging 192.168.2.1 with 32 bytes of data:

Request timed out.
Request timed out.
Request timed out.
Request timed out.
Request timed out.

Ping statistics for 192.168.2.1:
     Packets: Sent = 5, Received = 0, Lost = 5 (100% loss),  //未指定网关时不能ping通router1的s0，我理解为找不到出口，不知准确否
Approximate round trip times in milli-seconds:
     Minimum = 0ms, Maximum =  0ms, Average =  0ms

C:>ipconfig /dg 192.168.1.2                                  //指定网关为与本机直连的router1的e0口
C:>ping 192.168.1.2
Pinging 192.168.1.2 with 32 bytes of data:

Reply from 192.168.1.2: bytes=32 time=60ms TTL=241
Reply from 192.168.1.2: bytes=32 time=60ms TTL=241
Reply from 192.168.1.2: bytes=32 time=60ms TTL=241
Reply from 192.168.1.2: bytes=32 time=60ms TTL=241
Reply from 192.168.1.2: bytes=32 time=60ms TTL=241

Ping statistics for 192.168.1.2:     Packets: Sent = 5, Received = 5, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
     Minimum = 50ms, Maximum =  60ms, Average =  55ms

C:>ping 192.168.2.1
Pinging 192.168.2.1 with 32 bytes of data:

Reply from 192.168.2.1: bytes=32 time=60ms TTL=241
Reply from 192.168.2.1: bytes=32 time=60ms TTL=241
Reply from 192.168.2.1: bytes=32 time=60ms TTL=241
Reply from 192.168.2.1: bytes=32 time=60ms TTL=241
Reply from 192.168.2.1: bytes=32 time=60ms TTL=241

Ping statistics for 192.168.2.1:     Packets: Sent = 5, Received = 5, Lost = 0 (0% loss),      //指定网关后可以ping通s0口了
Approximate round trip times in milli-seconds:
     Minimum = 50ms, Maximum =  60ms, Average =  55ms

C:>ping 192.168.2.2
Pinging 192.168.2.2 with 32 bytes of data:

Reply from 192.168.2.2: bytes=32 time=60ms TTL=241
Reply from 192.168.2.2: bytes=32 time=60ms TTL=241
Reply from 192.168.2.2: bytes=32 time=60ms TTL=241
Reply from 192.168.2.2: bytes=32 time=60ms TTL=241
Reply from 192.168.2.2: bytes=32 time=60ms TTL=241

Ping statistics for 192.168.2.2:     Packets: Sent = 5, Received = 5, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
     Minimum = 50ms, Maximum =  60ms, Average =  55ms

C:>ping 192.168.3.1
Pinging 192.168.3.1 with 32 bytes of data:

Reply from 192.168.3.1: bytes=32 time=60ms TTL=241
Reply from 192.168.3.1: bytes=32 time=60ms TTL=241
Reply from 192.168.3.1: bytes=32 time=60ms TTL=241
Reply from 192.168.3.1: bytes=32 time=60ms TTL=241
Reply from 192.168.3.1: bytes=32 time=60ms TTL=241

Ping statistics for 192.168.3.1:     Packets: Sent = 5, Received = 5, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
     Minimum = 50ms, Maximum =  60ms, Average =  55ms

C:>ping 192.168.3.2
Pinging 192.168.3.2 with 32 bytes of data:

Reply from 192.168.3.2: bytes=32 time=60ms TTL=241
Reply from 192.168.3.2: bytes=32 time=60ms TTL=241
Reply from 192.168.3.2: bytes=32 time=60ms TTL=241
Reply from 192.168.3.2: bytes=32 time=60ms TTL=241
Reply from 192.168.3.2: bytes=32 time=60ms TTL=241

Ping statistics for 192.168.3.2:     Packets: Sent = 5, Received = 5, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
     Minimum = 50ms, Maximum =  60ms, Average =  55ms                                       //可以ping通任意一台设备的IP地址，实验成功
C:>

 

pc2 的配置如下：

 

Boson BOSS 5.0
Copyright 1998-2003 Boson Software, Inc.
Use the command help to get started

Press Enter to begin
C:>
C:>ipconfig /ip 192.168.3.2 255.255.255.0
C:>ipconfig /dg 192.168.3.1                          //把IP和网关设好
C:>ping 192.168.1.1
Pinging 192.168.1.1 with 32 bytes of data:

Reply from 192.168.1.1: bytes=32 time=60ms TTL=241
Reply from 192.168.1.1: bytes=32 time=60ms TTL=241
Reply from 192.168.1.1: bytes=32 time=60ms TTL=241
Reply from 192.168.1.1: bytes=32 time=60ms TTL=241
Reply from 192.168.1.1: bytes=32 time=60ms TTL=241

Ping statistics for 192.168.1.1:     Packets: Sent = 5, Received = 5, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
     Minimum = 50ms, Maximum =  60ms, Average =  55ms

C:>ping 192.168.1.2
Pinging 192.168.1.2 with 32 bytes of data:

Reply from 192.168.1.2: bytes=32 time=60ms TTL=241
Reply from 192.168.1.2: bytes=32 time=60ms TTL=241
Reply from 192.168.1.2: bytes=32 time=60ms TTL=241
Reply from 192.168.1.2: bytes=32 time=60ms TTL=241
Reply from 192.168.1.2: bytes=32 time=60ms TTL=241

Ping statistics for 192.168.1.2:     Packets: Sent = 5, Received = 5, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
     Minimum = 50ms, Maximum =  60ms, Average =  55ms

C:>ping 192.168.2.1
Pinging 192.168.2.1 with 32 bytes of data:

Reply from 192.168.2.1: bytes=32 time=60ms TTL=241
Reply from 192.168.2.1: bytes=32 time=60ms TTL=241
Reply from 192.168.2.1: bytes=32 time=60ms TTL=241
Reply from 192.168.2.1: bytes=32 time=60ms TTL=241
Reply from 192.168.2.1: bytes=32 time=60ms TTL=241

Ping statistics for 192.168.2.1:     Packets: Sent = 5, Received = 5, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
     Minimum = 50ms, Maximum =  60ms, Average =  55ms

C:>ping 192.168.2.2
Pinging 192.168.2.2 with 32 bytes of data:

Reply from 192.168.2.2: bytes=32 time=60ms TTL=241
Reply from 192.168.2.2: bytes=32 time=60ms TTL=241
Reply from 192.168.2.2: bytes=32 time=60ms TTL=241
Reply from 192.168.2.2: bytes=32 time=60ms TTL=241
Reply from 192.168.2.2: bytes=32 time=60ms TTL=241

Ping statistics for 192.168.2.2:     Packets: Sent = 5, Received = 5, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
     Minimum = 50ms, Maximum =  60ms, Average =  55ms

C:>ping 192.168.3.1
Pinging 192.168.3.1 with 32 bytes of data:

Reply from 192.168.3.1: bytes=32 time=60ms TTL=241
Reply from 192.168.3.1: bytes=32 time=60ms TTL=241
Reply from 192.168.3.1: bytes=32 time=60ms TTL=241
Reply from 192.168.3.1: bytes=32 time=60ms TTL=241
Reply from 192.168.3.1: bytes=32 time=60ms TTL=241

Ping statistics for 192.168.3.1:     Packets: Sent = 5, Received = 5, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
     Minimum = 50ms, Maximum =  60ms, Average =  55ms  //可以ping通任意一台设备的IP地址，实验成功