HCL配置不同VLAN之间进行通讯实验

VLAN配置示例

实验拓扑

配置命令如下：

• 首先对4台评测机进行IP地址的配置
• 见拓扑图划红框的是各pc机的IP和掩码
• 进行连线，拓扑图中有各接口的编号
• 注：PC机点了启用后也可能会有down的状态，解决方法目前有重新连线或从新接一台pc机；交换机也可能出现敲上的命令查不到的情况，这种情况对交换机进行保存命令（save），然后进行重启（reboot）。
  
  配置好IP和掩码后点启用，一定要确保状态是UP的

交换机 S5820V2-54QS-GE_1

[H3C]vlan 10
[H3C-vlan10]qu
[H3C]vlan 20
[H3C-vlan20]qu
[H3C]int g 1/0/1
[H3C-GigabitEthernet1/0/1]port link-type access
[H3C-GigabitEthernet1/0/1]port access vlan 10
[H3C-GigabitEthernet1/0/1]qu
[H3C]int g1/0/2
[H3C-GigabitEthernet1/0/2]port link-type access
[H3C-GigabitEthernet1/0/2]port access vlan 20
[H3C-GigabitEthernet1/0/2]qu
[H3C]int g1/0/24
[H3C-GigabitEthernet1/0/24]port link-type trunk
[H3C-GigabitEthernet1/0/24]port trunk permit vlan 10 20
[H3C-GigabitEthernet1/0/24]qu
[H3C]int g 1/0/1
[H3C-GigabitEthernet1/0/1]port link-type hybrid
[H3C-GigabitEthernet1/0/1]port hybrid vlan 10 20 untagged
[H3C-GigabitEthernet1/0/1]qu
[H3C]int g1/0/2
[H3C-GigabitEthernet1/0/2]port link-type hybrid
[H3C-GigabitEthernet1/0/2]port hybrid vlan 10 20 untagged
[H3C-GigabitEthernet1/0/2]qu

交换机 S5820V2-54QS-GE_2

[H3C]vlan 10
[H3C-vlan10]qu
[H3C]vlan 20
[H3C-vlan20]qu
[H3C]int g1/0/1
[H3C-GigabitEthernet1/0/1]port link-type access     //设置为access端口
[H3C-GigabitEthernet1/0/1]port access vlan 10     //把端口加入VLAN里
[H3C-GigabitEthernet1/0/1]qu
[H3C]int g1/0/2
[H3C-GigabitEthernet1/0/2]port link-type access
[H3C-GigabitEthernet1/0/2]port access vlan 20
[H3C-GigabitEthernet1/0/2]qu
[H3C]int g 1/0/24
[H3C-GigabitEthernet1/0/24]port link-type trunk
[H3C-GigabitEthernet1/0/24]port trunk permit vlan 10 20
[H3C-GigabitEthernet1/0/24]qu
[H3C]int g1/0/1
[H3C-GigabitEthernet1/0/1]port link-type hybrid     //设置为混杂端口
[H3C-GigabitEthernet1/0/1]port hybrid vlan 10 20 untagged     //去掉VLAN10,20的标签
[H3C-GigabitEthernet1/0/1]qu
[H3C]int g1/0/2
[H3C-GigabitEthernet1/0/2]port link-type hybrid
[H3C-GigabitEthernet1/0/2]port hybrid vlan 10 20 untagged
[H3C-GigabitEthernet1/0/2]qu

配置完成后用一台pc机ping其余三台pc机
成功后如下图所示：