MT7688 原厂sdk启动日志
U-Boot 1.1.3 (Sep 15 2014 - 10:02:31)
Board: Ralink APSoC DRAM: 64 MB
relocate_code Pointer at: 83fb8000
******************************
Software System Reset Occurred
******************************
flash manufacture id: ef, device id 40 17
find flash: W25Q64BV
raspi_read: from:40035 len:1
0x893
raspi_read: from:30000 len:1000
0x7deaa
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 4.3.S.0
--------------------------------------------
ASIC 7628_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Sep 15 2014 Time:10:02:31
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 575 MHZ ####
estimate memory size =64 Mbytes
RESET MT7628 PHY!!!!!!
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
default: 3
0
3: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
0x1fa0
Image Name: Linux Kernel Image
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 5375298 Bytes = 5.1 MB
Load Address: 80000000
Entry Point: 8000c120
raspi_read: from:50040 len:520542
0x2856e9e4
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8000c120) ...
## Giving linux memsize in MB, 64
Starting kernel ...
LINUX started...
THIS IS ASIC
Linux version 2.6.36 (root@jimith--machine) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #10 Tue Dec 2 19:22:22 CST 2014
The CPU feqenuce set to 575 MHz
MIPS CPU sleep mode enabled.
CPU revision is: 00019655 (MIPS 24Kc)
Software DMA cache coherency
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: console=ttyS1,57600n8 root=/dev/ram0 console=ttyS0
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, , 4-waylinesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=00049724
Readback ErrCtl register=00049724
Memory: 55952k/65536k available (4061k kernel code, 9584k reserved, 1063k data, 3596k init, 0k highmem)
NR_IRQS:128
console [ttyS1] enabled
Calibrating delay loop... 386.04 BogoMIPS (lpj=772096)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
RALINK_GPIOMODE = 54050404
RALINK_GPIOMODE = 54040404
Port 0 N_FTS = 1b105000
start PCIe register access
RALINK_RSTCTRL = 2400000
RALINK_CLKCFG1 = fdbfffc0
*************** MT7628 PCIe RC mode *************
PCIE0 no card, disable it(RST&CLK)
bio: create slab at 0
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource Ralink Systick timer
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RT3xxx EHCI/OHCI init.
NTFS driver 2.1.29 [Flags: R/W].
fuse init (API version 7.15)
msgmni has been set to 109
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered (default)
doit
Ralink gpio driver initialized
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x10000d00 (irq = 21) is a 16550A
serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
brd: module loaded
osst :I: Tape driver with OnStream support version 0.99.4
osst :I: $Id: //WIFI_SOC/MP/SDK_4_3_0_0/RT288x_SDK/source/linux-2.6.36.x/drivers/scsi/osst.c#1 $
SCSI Media Changer driver v0.25
flash manufacture id: ef, device id 40 17
W25Q64BV(ef 40170000) (8192 Kbytes)
mtd .name = raspi, .size = 0x00800000 (8M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 5 MTD partitions on "raspi":
0x000000000000-0x000000800000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000001000000 : "Kernel"
mtd: partition "Kernel" extends beyond the end of device "raspi" -- size truncated to 0x7b0000
rdm_major = 253
GMAC1_MAC_ADRH -- : 0x0000000c
GMAC1_MAC_ADRL -- : 0x43e17629
Ralink APSoC Ethernet Driver Initilization. v3.1 512 rx/tx descriptors allocated, mtu = 1500!
GMAC1_MAC_ADRH -- : 0x0000000c
GMAC1_MAC_ADRL -- : 0x43e17629
PROC INIT OK!
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPTP driver version 0.8.5
=== pAd = c0147000, size = 1029352 ===
<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
RtmpChipOpsHook(493): Not support for HIF_MT yet!
mt7628_init()-->
mt7628_init(FW(8a00), HW(8a01), CHIPID(7628))
e2.bin mt7628_init(1102)::(2), pChipCap->fw_len(63508)
mt_bcn_buf_init(218): Not support for HIF_MT yet!
<--mt7628_init()
usbmon: debugfs is not available
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
FM_OUT value: u4FmOut = 134(0x00000086)
FM detection done! loop = 0
SR calibration value u1SrCalVal = 6
rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller
rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1
rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000
rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: Ralink EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.36 ehci_hcd
usb usb1: SerialNumber: rt3xxx
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller
rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2
rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: RT3xxx OHCI Controller
usb usb2: Manufacturer: Linux 2.6.36 ohci_hcd
usb usb2: SerialNumber: rt3xxx-ohci
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (874 buckets, 3496 max)
ctnetlink v0.93: registering with nfnetlink.
matchsize=264
xt_time: kernel timezone is -0000
IPVS: Registered protocols ()
IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
IPVS: ipvs loaded.
IPv4 over IPv4 tunneling driver
GRE over IPv4 demultiplexor driver
gre: can't add protocol
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 17
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
802.1Q VLAN Support v1.8 Ben Greear
All bugs added by David S. Miller
Warning: unable to open an initial console.
Freeing unused kernel memory: 3596k freed
Algorithmics/MIPS FPU Emulator v1.5
Welcome to
__ ___ _____ _____ _ _______ ______ _____ _ ___
| \ / || ___|| __ \ | || __ ||__ __|| ___|| | / /
| ^ || |__ | | \ \| || | | | | | | |__ | |/ /
| | | || ___|| | | || || |__| | | | | ___|| \
| | | || |___ | |__/ /| || __ | | | | |___ | |\ \
|__| |___||_____||_____/ |_||_| |_| |_| |_____||_| \__\
= Everyday Genius =
Password for 'admin' changed
##### disable 1st wireless interface #####
TX_BCN DESC a2b91000 size = 320
RX[0] DESC a2b93000 size = 2048
RX[1] DESC a2b94000 size = 2048
E2pAccessMode=0
cfg_mode=9
cfg_mode=9
wmode_band_equal(): Band Equal!
APSDCapable[0]=0
APSDCapable[1]=0
APSDCapable[2]=0
APSDCapable[3]=0
APSDCapable[4]=0
APSDCapable[5]=0
APSDCapable[6]=0
APSDCapable[7]=0
APSDCapable[8]=0
APSDCapable[9]=0
APSDCapable[10]=0
APSDCapable[11]=0
APSDCapable[12]=0
APSDCapable[13]=0
APSDCapable[14]=0
APSDCapable[15]=0
default ApCliAPSDCapable[0]=0
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
load fw image from fw_header_image
AndesMTLoadFwMethod1(2056)::pChipCap->fw_len(63508)
20140811CmdAddressLenReq:(ret = 0)
CmdFwStartReq: override = 1, address = 1048576
CmdStartDLRsp: WiFI FW Download Success
command (ed), ext_cmd_type (f), seq(3), timeout(3000ms)
txq qlen = 0
rxq qlen = 0
kickq qlen = 0
ackq qlen = 1
tx_doneq.qlen = 0
rx_done qlen = 0
AndesSendCmdMsg: msg state = 8
msg->retransmit_times = 0
efuse_probe: efuse = 10000002
RtmpChipOpsEepromHook::e2p_type=3, inf_Type=4
RtmpEepromGetDefault::e2p_dafault=2
RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 3, E2P default = 2
NVM is FLASH mode
1. Phy Mode = 14
CmdSlotTimeSet:(ret = 0)
Country Region from e2p = ffff
tssi_1_target_pwr_g_band = 35
2. Phy Mode = 14
3. Phy Mode = 14
NICInitPwrPinCfg(13): Not support for HIF_MT yet!
NICInitializeAsic(595): Not support rtmp_mac_sys_reset () for HIF_MT yet!
mt_mac_init()-->
MtAsicInitMac()-->
mt7628_init_mac_cr()-->
MtAsicSetMacMaxLen(1221): Set the Max RxPktLen=1024!
<--mt_mac_init()
WTBL Segment 1 info:
MemBaseAddr/FID:0x28000/0
EntrySize/Cnt:32/128
WTBL Segment 2 info:
MemBaseAddr/FID:0x40000/0
EntrySize/Cnt:64/128
WTBL Segment 3 info:
MemBaseAddr/FID:0x42000/64
EntrySize/Cnt:64/128
WTBL Segment 4 info:
MemBaseAddr/FID:0x44000/128
EntrySize/Cnt:32/128
AntCfgInit(2479): Not support for HIF_MT yet!
MCS Set = ff ff 00 00 01
MtAsicSetChBusyStat(834): Not support for HIF_MT yet!
[PMF]ap_pmf_init:: apidx=0, MFPC=0, MFPR=0, SHA256=0
AsicSetRDG(): NotSupportedFunc for this arch(HIF_MT)!
MtAsicSetRalinkBurstMode(2753): Not support for HIF_MT yet!
MtAsicSetPiggyBack(771): Not support for HIF_MT yet!
mt7628_switch_channel(): Switch to Ch#3(2T2R), BBP_BW=1
MtAsicSetTxPreamble(2732): Not support for HIF_MT yet!
MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0
Main bssid = 00:0c:43:e1:76:28
<==== rt28xx_init, Status=0
ifconfig: ioctl 0x8913 failed: No such device
brctl: bridge br0: No such device or address
##### configVIF #####
Raeth v3.1 (Tasklet,SkbRecycle)
phy_tx_ring = 0x027ce000, tx_ring = 0xa27ce000
phy_rx_ring0 = 0x027d0000, rx_ring0 = 0xa27d0000
GMAC1_MAC_ADRH -- : 0x0000000c
GMAC1_MAC_ADRL -- : 0x43e17629
RT305x_ESW: Link Status Changed
vconfig: ioctl error for rem: No such device
vconfig: ioctl error for rem: No such device
/sbin/internet.sh: line 940: rmmod: not found
device eth2 entered promiscuous mode
##### config Ralink ESW vlan partition (LLLLW) #####
switch reg write offset=14, value=405555
switch reg write offset=50, value=2001
switch reg write offset=98, value=7f3f
switch reg write offset=e4, value=3f
switch reg write offset=40, value=1001
switch reg write offset=44, value=1001
switch reg write offset=48, value=1002
switch reg write offset=70, value=ffff506f
done.
device ra0 entered promiscuous mode
device eth2.1 entered promiscuous mode
udhcpc (v1.12.1) started
br0: port 2(eth2.1) entering learning state
br0: port 2(eth2.1) entering learning state
br0: port 1(ra0) entering learning state
br0: port 1(ra0) entering learning state
ifconfig: ioctl 0x8914 failed: Cannot assign requested address
ifconfig: ioctl 0x8914 failed: Cannot assign requested address
br0: port 2(eth2.1) entering forwarding state
br0: port 1(ra0) entering forwarding state
killall: udhcpd: no process killed
Set: phy[0].reg[0] = 3900
Set: phy[1].reg[0] = 3900
Set: phy[2].reg[0] = 3900
Set: phy[3].reg[0] = 3900
Set: phy[0].reg[0] = 3300
Set: phy[1].reg[0] = 3300
Set: phy[2].reg[0] = 3300
Set: phy[3].reg[0] = 3300
ifconfig: ioctl 0x8913 failed: No such device
/bin/radvd.sh: line 7: cannot create /proc/sys/net/ipv6/conf/all/forwarding: nonexistent directory
rm: cannot remove '/etc/radvd.conf': No such file or directory
route: ioctl 0x890c failed: No such process
APUpdateBeaconFrame()=>BSS0:BcnPkt not idle(3)!
killall: rt2860apd: no process killed
iptables v1.4.10: Couldn't load target `macipport_filter':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables v1.4.10: Couldn't load target `web_filter':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables v1.4.10: Couldn't load target `malicious_filter':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables v1.4.10: Couldn't load target `malicious_input_filter':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables v1.4.10: Couldn't load target `port_trigger':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables v1.4.10: Couldn't load target `trigger_prerouting':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
sh: /bin/super_dmz: not found
iptables v1.4.10: Couldn't load target `port_forward':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables v1.4.10: Couldn't load target `DMZ':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
180
0
180
0
sh: ddns.sh: not found
webs: Listening for HTTP requests at address 192.168.2.55
##### Hotplug USB device init #####
1st partition does not exist
1970-01-01 00:00:19: (log.c.97) server started
init: can't log to /dev/tty5
starting pid 1234, tty '/dev/ttyS1': '/bin/sh'
BusyBox v1.12.1 (2014-10-30 05:11:04 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
Board: Ralink APSoC DRAM: 64 MB
relocate_code Pointer at: 83fb8000
******************************
Software System Reset Occurred
******************************
flash manufacture id: ef, device id 40 17
find flash: W25Q64BV
raspi_read: from:40035 len:1
0x893
raspi_read: from:30000 len:1000
0x7deaa
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 4.3.S.0
--------------------------------------------
ASIC 7628_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Sep 15 2014 Time:10:02:31
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 575 MHZ ####
estimate memory size =64 Mbytes
RESET MT7628 PHY!!!!!!
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
default: 3
0
3: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
0x1fa0
Image Name: Linux Kernel Image
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 5375298 Bytes = 5.1 MB
Load Address: 80000000
Entry Point: 8000c120
raspi_read: from:50040 len:520542
0x2856e9e4
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8000c120) ...
## Giving linux memsize in MB, 64
Starting kernel ...
LINUX started...
THIS IS ASIC
Linux version 2.6.36 (root@jimith--machine) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #10 Tue Dec 2 19:22:22 CST 2014
The CPU feqenuce set to 575 MHz
MIPS CPU sleep mode enabled.
CPU revision is: 00019655 (MIPS 24Kc)
Software DMA cache coherency
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: console=ttyS1,57600n8 root=/dev/ram0 console=ttyS0
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, , 4-waylinesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=00049724
Readback ErrCtl register=00049724
Memory: 55952k/65536k available (4061k kernel code, 9584k reserved, 1063k data, 3596k init, 0k highmem)
NR_IRQS:128
console [ttyS1] enabled
Calibrating delay loop... 386.04 BogoMIPS (lpj=772096)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
RALINK_GPIOMODE = 54050404
RALINK_GPIOMODE = 54040404
Port 0 N_FTS = 1b105000
start PCIe register access
RALINK_RSTCTRL = 2400000
RALINK_CLKCFG1 = fdbfffc0
*************** MT7628 PCIe RC mode *************
PCIE0 no card, disable it(RST&CLK)
bio: create slab
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource Ralink Systick timer
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RT3xxx EHCI/OHCI init.
NTFS driver 2.1.29 [Flags: R/W].
fuse init (API version 7.15)
msgmni has been set to 109
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered (default)
doit
Ralink gpio driver initialized
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x10000d00 (irq = 21) is a 16550A
serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
brd: module loaded
osst :I: Tape driver with OnStream support version 0.99.4
osst :I: $Id: //WIFI_SOC/MP/SDK_4_3_0_0/RT288x_SDK/source/linux-2.6.36.x/drivers/scsi/osst.c#1 $
SCSI Media Changer driver v0.25
flash manufacture id: ef, device id 40 17
W25Q64BV(ef 40170000) (8192 Kbytes)
mtd .name = raspi, .size = 0x00800000 (8M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 5 MTD partitions on "raspi":
0x000000000000-0x000000800000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000001000000 : "Kernel"
mtd: partition "Kernel" extends beyond the end of device "raspi" -- size truncated to 0x7b0000
rdm_major = 253
GMAC1_MAC_ADRH -- : 0x0000000c
GMAC1_MAC_ADRL -- : 0x43e17629
Ralink APSoC Ethernet Driver Initilization. v3.1 512 rx/tx descriptors allocated, mtu = 1500!
GMAC1_MAC_ADRH -- : 0x0000000c
GMAC1_MAC_ADRL -- : 0x43e17629
PROC INIT OK!
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPTP driver version 0.8.5
=== pAd = c0147000, size = 1029352 ===
<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
RtmpChipOpsHook(493): Not support for HIF_MT yet!
mt7628_init()-->
mt7628_init(FW(8a00), HW(8a01), CHIPID(7628))
e2.bin mt7628_init(1102)::(2), pChipCap->fw_len(63508)
mt_bcn_buf_init(218): Not support for HIF_MT yet!
<--mt7628_init()
usbmon: debugfs is not available
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
FM_OUT value: u4FmOut = 134(0x00000086)
FM detection done! loop = 0
SR calibration value u1SrCalVal = 6
rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller
rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1
rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000
rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: Ralink EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.36 ehci_hcd
usb usb1: SerialNumber: rt3xxx
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller
rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2
rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: RT3xxx OHCI Controller
usb usb2: Manufacturer: Linux 2.6.36 ohci_hcd
usb usb2: SerialNumber: rt3xxx-ohci
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (874 buckets, 3496 max)
ctnetlink v0.93: registering with nfnetlink.
matchsize=264
xt_time: kernel timezone is -0000
IPVS: Registered protocols ()
IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
IPVS: ipvs loaded.
IPv4 over IPv4 tunneling driver
GRE over IPv4 demultiplexor driver
gre: can't add protocol
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 17
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
802.1Q VLAN Support v1.8 Ben Greear
All bugs added by David S. Miller
Warning: unable to open an initial console.
Freeing unused kernel memory: 3596k freed
Algorithmics/MIPS FPU Emulator v1.5
Welcome to
__ ___ _____ _____ _ _______ ______ _____ _ ___
| \ / || ___|| __ \ | || __ ||__ __|| ___|| | / /
| ^ || |__ | | \ \| || | | | | | | |__ | |/ /
| | | || ___|| | | || || |__| | | | | ___|| \
| | | || |___ | |__/ /| || __ | | | | |___ | |\ \
|__| |___||_____||_____/ |_||_| |_| |_| |_____||_| \__\
= Everyday Genius =
Password for 'admin' changed
##### disable 1st wireless interface #####
TX_BCN DESC a2b91000 size = 320
RX[0] DESC a2b93000 size = 2048
RX[1] DESC a2b94000 size = 2048
E2pAccessMode=0
cfg_mode=9
cfg_mode=9
wmode_band_equal(): Band Equal!
APSDCapable[0]=0
APSDCapable[1]=0
APSDCapable[2]=0
APSDCapable[3]=0
APSDCapable[4]=0
APSDCapable[5]=0
APSDCapable[6]=0
APSDCapable[7]=0
APSDCapable[8]=0
APSDCapable[9]=0
APSDCapable[10]=0
APSDCapable[11]=0
APSDCapable[12]=0
APSDCapable[13]=0
APSDCapable[14]=0
APSDCapable[15]=0
default ApCliAPSDCapable[0]=0
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
load fw image from fw_header_image
AndesMTLoadFwMethod1(2056)::pChipCap->fw_len(63508)
20140811CmdAddressLenReq:(ret = 0)
CmdFwStartReq: override = 1, address = 1048576
CmdStartDLRsp: WiFI FW Download Success
command (ed), ext_cmd_type (f), seq(3), timeout(3000ms)
txq qlen = 0
rxq qlen = 0
kickq qlen = 0
ackq qlen = 1
tx_doneq.qlen = 0
rx_done qlen = 0
AndesSendCmdMsg: msg state = 8
msg->retransmit_times = 0
efuse_probe: efuse = 10000002
RtmpChipOpsEepromHook::e2p_type=3, inf_Type=4
RtmpEepromGetDefault::e2p_dafault=2
RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 3, E2P default = 2
NVM is FLASH mode
1. Phy Mode = 14
CmdSlotTimeSet:(ret = 0)
Country Region from e2p = ffff
tssi_1_target_pwr_g_band = 35
2. Phy Mode = 14
3. Phy Mode = 14
NICInitPwrPinCfg(13): Not support for HIF_MT yet!
NICInitializeAsic(595): Not support rtmp_mac_sys_reset () for HIF_MT yet!
mt_mac_init()-->
MtAsicInitMac()-->
mt7628_init_mac_cr()-->
MtAsicSetMacMaxLen(1221): Set the Max RxPktLen=1024!
<--mt_mac_init()
WTBL Segment 1 info:
MemBaseAddr/FID:0x28000/0
EntrySize/Cnt:32/128
WTBL Segment 2 info:
MemBaseAddr/FID:0x40000/0
EntrySize/Cnt:64/128
WTBL Segment 3 info:
MemBaseAddr/FID:0x42000/64
EntrySize/Cnt:64/128
WTBL Segment 4 info:
MemBaseAddr/FID:0x44000/128
EntrySize/Cnt:32/128
AntCfgInit(2479): Not support for HIF_MT yet!
MCS Set = ff ff 00 00 01
MtAsicSetChBusyStat(834): Not support for HIF_MT yet!
[PMF]ap_pmf_init:: apidx=0, MFPC=0, MFPR=0, SHA256=0
AsicSetRDG(): NotSupportedFunc for this arch(HIF_MT)!
MtAsicSetRalinkBurstMode(2753): Not support for HIF_MT yet!
MtAsicSetPiggyBack(771): Not support for HIF_MT yet!
mt7628_switch_channel(): Switch to Ch#3(2T2R), BBP_BW=1
MtAsicSetTxPreamble(2732): Not support for HIF_MT yet!
MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0
Main bssid = 00:0c:43:e1:76:28
<==== rt28xx_init, Status=0
ifconfig: ioctl 0x8913 failed: No such device
brctl: bridge br0: No such device or address
##### configVIF #####
Raeth v3.1 (Tasklet,SkbRecycle)
phy_tx_ring = 0x027ce000, tx_ring = 0xa27ce000
phy_rx_ring0 = 0x027d0000, rx_ring0 = 0xa27d0000
GMAC1_MAC_ADRH -- : 0x0000000c
GMAC1_MAC_ADRL -- : 0x43e17629
RT305x_ESW: Link Status Changed
vconfig: ioctl error for rem: No such device
vconfig: ioctl error for rem: No such device
/sbin/internet.sh: line 940: rmmod: not found
device eth2 entered promiscuous mode
##### config Ralink ESW vlan partition (LLLLW) #####
switch reg write offset=14, value=405555
switch reg write offset=50, value=2001
switch reg write offset=98, value=7f3f
switch reg write offset=e4, value=3f
switch reg write offset=40, value=1001
switch reg write offset=44, value=1001
switch reg write offset=48, value=1002
switch reg write offset=70, value=ffff506f
done.
device ra0 entered promiscuous mode
device eth2.1 entered promiscuous mode
udhcpc (v1.12.1) started
br0: port 2(eth2.1) entering learning state
br0: port 2(eth2.1) entering learning state
br0: port 1(ra0) entering learning state
br0: port 1(ra0) entering learning state
ifconfig: ioctl 0x8914 failed: Cannot assign requested address
ifconfig: ioctl 0x8914 failed: Cannot assign requested address
br0: port 2(eth2.1) entering forwarding state
br0: port 1(ra0) entering forwarding state
killall: udhcpd: no process killed
Set: phy[0].reg[0] = 3900
Set: phy[1].reg[0] = 3900
Set: phy[2].reg[0] = 3900
Set: phy[3].reg[0] = 3900
Set: phy[0].reg[0] = 3300
Set: phy[1].reg[0] = 3300
Set: phy[2].reg[0] = 3300
Set: phy[3].reg[0] = 3300
ifconfig: ioctl 0x8913 failed: No such device
/bin/radvd.sh: line 7: cannot create /proc/sys/net/ipv6/conf/all/forwarding: nonexistent directory
rm: cannot remove '/etc/radvd.conf': No such file or directory
route: ioctl 0x890c failed: No such process
APUpdateBeaconFrame()=>BSS0:BcnPkt not idle(3)!
killall: rt2860apd: no process killed
iptables v1.4.10: Couldn't load target `macipport_filter':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables v1.4.10: Couldn't load target `web_filter':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables v1.4.10: Couldn't load target `malicious_filter':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables v1.4.10: Couldn't load target `malicious_input_filter':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables v1.4.10: Couldn't load target `port_trigger':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables v1.4.10: Couldn't load target `trigger_prerouting':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
sh: /bin/super_dmz: not found
iptables v1.4.10: Couldn't load target `port_forward':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables v1.4.10: Couldn't load target `DMZ':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
180
0
180
0
sh: ddns.sh: not found
webs: Listening for HTTP requests at address 192.168.2.55
##### Hotplug USB device init #####
1st partition does not exist
1970-01-01 00:00:19: (log.c.97) server started
init: can't log to /dev/tty5
starting pid 1234, tty '/dev/ttyS1': '/bin/sh'
BusyBox v1.12.1 (2014-10-30 05:11:04 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.