PIC16F877A 定时器实验1

/*********************
Forum:http://bbs.cepark.com
Author:hnrain
Date:2010-12-28
Email:[email protected]
***************************
TMR0用作定时器时，定时器时钟＝系统时钟/4；
写TMR0时，会产生2个周期的的延时，如果不使用前置分频器，可通过设置
初值进行补偿。
例如 需要定时200个时钟周期时，TMR0 = 256 -200 + 2= 58

OPTION_REG:

bit5 T0CS:TMR0 Clock Source Select bit

       1 = Transition on T0CKI pin

       0 = Internal instruction cycle clock(CLKO)

bit 4 T0SE:TMR0 Source Edge Select bit

       1 = Increment on high-to-low transition on T0CKI pin

       0 = Increment on low-to-high transition on T0CKI pin

bit 3 PSA:Prescaler Assignment bit

      1 = Prescaler is assigned to the WDT

      0 = Prescaler is assigned to the Timer0 module

bit2-0 PS2:PS0:Prescaler Rate Select bits

给大家一个意见：如果想用TMR0实现精确的定时，一旦用了预分频器后就不要对TMR0做任何写操作。

注意：在中断服务程序中查询TMR0中断时，既要查询T0IE位，还要查询T0IF位。
***********************/
#include
#include "../head/config.h"

__CONFIG(HS&WDTDIS&LVPDIS&PWRTEN);
//HS振荡,禁止看门狗,低压编程关闭,启动延时定时器

uint16 count = 0;
void main(void)
{
    PSA = 1;//prescaler is assigned to the WDT
    T0CS  = 0;//Internal instruction cycle clock

    TMR0 = 58;//timer 200 cycle clock

    GIE = 1;//global interrupt enable
    T0IE = 1;//TMR0 interrupt enable

    PORTD = 0x00;
    TRISD = 0x00;

    while(1)
    {}
}

void interrupt ISR(void)
{
    if(T0IE && T0IF)
    {
        T0IF = 0;
        count++;
        if(count == 1000)
        {
        count = 0;
        PORTD = ~PORTD;
        }
        TMR0 = TMR0 + 58;
    }
}

 

/*********************
Forum:http://bbs.cepark.com
Author:hnrain
Date:2010-12-28
Email:[email protected]
***************************
TMR0用作定时器时，定时器时钟＝系统时钟/4；
写TMR0时，会产生2个周期的的延时，如果不使用前置分频器，可通过设置
初值进行补偿。
例如 需要定时200个时钟周期时，TMR0 = 256 -200 + 2= 58


OPTION_REG:

bit5 T0CS:TMR0 Clock Source Select bit

       1 = Transition on T0CKI pin

       0 = Internal instruction cycle clock(CLKO)

bit 4 T0SE:TMR0 Source Edge Select bit

       1 = Increment on high-to-low transition on T0CKI pin

       0 = Increment on low-to-high transition on T0CKI pin

bit 3 PSA:Prescaler Assignment bit

      1 = Prescaler is assigned to the WDT

      0 = Prescaler is assigned to the Timer0 module

bit2-0 PS2:PS0:Prescaler Rate Select bits

给大家一个意见：如果想用TMR0实现精确的定时，一旦用了预分频器后就不要对TMR0做任何写操作。

注意：在中断服务程序中查询TMR0中断时，既要查询T0IE位，还要查询T0IF位。
***********************/
#include 
#include "../head/config.h"


__CONFIG(HS&WDTDIS&LVPDIS&PWRTEN);
//HS振荡,禁止看门狗,低压编程关闭,启动延时定时器

uint16 count = 0;
void main(void)
{
	PSA = 1;//prescaler is assigned to the WDT
	T0CS  = 0;//Internal instruction cycle clock

	TMR0 = 58;//timer 200 cycle clock

	GIE = 1;//global interrupt enable
	T0IE = 1;//TMR0 interrupt enable

	PORTD = 0x00;
	TRISD = 0x00;

	while(1)
	{}
}

void interrupt ISR(void)
{
	if(T0IE && T0IF)
	{
		T0IF = 0;
		count++;
		if(count == 1000)
		{
		count = 0;
		PORTD = ~PORTD;
		}
		
		TMR0 = TMR0 + 58;
	}
}

转载于:https://www.cnblogs.com/hnrainll/archive/2010/12/28/1918449.html