macOS - networksetup 命令

networksetup

---

命令手册：

$ man networksetup

可以知道 networksetup 命令地址是：/usr/sbin/networksetup

---

The networksetup command is used to configure network settings typically configured in
    the System Preferences application.  The networksetup command requires at least "admin"
    privileges to run. Most of the set commands require "root" privileges to run.
	Any flag that takes a password will accept "-" in place of the password to indicate it
     should read the password from stdin.

networksetup 命令是用来配置 系统偏好设置中的 网络设置，networksetup 需要至少 admin 权限来运行。部分命令需要 root 权限。

---

方法及使用

networkservice

[-listnetworkserviceorder] 
[-listallnetworkservices]
[-getinfo networkservice]

使用示例：
1

$ networksetup -getinfo "Wi-Fi"
DHCP Configuration
IP address: 10.2.5.1
Subnet mask: 255.255.0.0
Router: 10.24.0.1
Client ID: 
IPv6: Automatic
IPv6 IP address: none
IPv6 Router: none
Wi-Fi ID: 88:88:98:cc:22:00

2

$ networksetup -listnetworkserviceorder
An asterisk (*) denotes that a network service is disabled.
(1) iPad USB
(Hardware Port: iPad USB, Device: en5)

(2) iPhone USB
(Hardware Port: iPhone USB, Device: en4)

(3) Wi-Fi
(Hardware Port: Wi-Fi, Device: en0)

(4) Bluetooth PAN
(Hardware Port: Bluetooth PAN, Device: en3)

(5) Thunderbolt Bridge
(Hardware Port: Thunderbolt Bridge, Device: bridge0)

3

$ networksetup -listallnetworkservices
An asterisk (*) denotes that a network service is disabled.
iPad USB
iPhone USB
Wi-Fi
Bluetooth PAN
Thunderbolt Bridge

---

hardwareports

[-listallhardwareports] 
[-detectnewhardware]
[-getmacaddress hardwareport] 

使用示例：

$ networksetup -listallhardwareports

Hardware Port: Wi-Fi
Device: en0
Ethernet Address: 88:88:98:cc:22:00

Hardware Port: Bluetooth PAN
Device: en3
Ethernet Address: 88:88:98:cc:22:01

Hardware Port: Thunderbolt 1
Device: en1
Ethernet Address: 88:88:98:cc:22:02

Hardware Port: Thunderbolt 2
Device: en2
Ethernet Address: 88:88:98:cc:22:03

Hardware Port: Thunderbolt Bridge
Device: bridge0
Ethernet Address: 88:88:98:cc:22:04

VLAN Configurations
===================

---

computername

[-getcomputername]
[-setcomputername computername] 

---

dhcp、route、domain

[-setmanual networkservice ip subnet router]
[-setdhcp networkservice [clientid]] 
[-setbootp networkservice]
[-setmanualwithdhcprouter networkservice ip]
[-getadditionalroutes networkservice]
[-setadditionalroutes networkservice [dest1 mask1 gate1] [dest2 mask2 gate2] ..
. [destN maskN gateN]]

使用示例：

$ networksetup -setmanual "Built-in Ethernet" 192.168.100.100 255.255.255.0 192.168.100.1

---

ipv4 & ipv6

[-setv4off networkservice] 
[-setv6off networkservice]
[-setv6automatic networkservice]
[-setv6linklocal networkservice]
[-setv6manual networkservice address prefixLength router]
[-getv6additionalroutes networkservice]
[-setv6additionalroutes networkservice [dest1 prefixlength1 gate1] [dest2 prefi
xlength2 gate2] ... [destN prefixlengthN gateN]]

---

dns

[-getdnsservers networkservice]
[-setdnsservers networkservice dns1 [dns2] [...]]

使用示例：

$ networksetup -setdnsservers "Built-in Ethernet" 192.168.100.100 192.168.100.12

$ networksetup -getdnsservers "Wi-Fi"
There aren't any DNS Servers set on Wi-Fi.

$ networksetup -getdnsservers en0
en0 is not a recognized network service.
** Error: The parameters were not valid.

---

domain

[-getsearchdomains networkservice]
[-setsearchdomains networkservice domain1 [domain2] [...]]
[-create6to4service networkservicename]
[-set6to4automatic networkservice]
[-set6to4manual networkservice relayAddress]

networksetup -setsearchdomains "Built-in Ethernet" company.com corp.com

---

代理 proxy

ftp代理

[-getftpproxy networkservice]
[-setftpproxy networkservice domain portnumber authenticated username password]
[-setftpproxystate networkservice on | off]

网页代理

[-getwebproxy networkservice]
[-setwebproxy networkservice domain portnumber authenticated username password]
[-setwebproxystate networkservice on | off]

$ networksetup -setwebproxy "Built-in Ethernet" proxy.company.com 80

$ networksetup -setwebproxy "Built-In Ethernet" proxy.company.com 80 On authusername
     authpassword

---

安全网页代理

[-getsecurewebproxy networkservice]
[-setsecurewebproxy networkservice domain portnumber authenticated username password]
[-setsecurewebproxystate networkservice on | off]

使用示例：

$ networksetup -getsecurewebproxy Wi-Fi
Enabled: No
Server: 
Port: 0
Authenticated Proxy Enabled: 0

$ networksetup -getsecurewebproxy en6
** Error: Unable to find item in network database.

---

流代理

[-getstreamingproxy networkservice]
[-setstreamingproxy networkservice domain portnumber authenticated username password]
[-setstreamingproxystate networkservice on | off]

gopher 代理

[-getgopherproxy networkservice]
[-setgopherproxy networkservice domain portnumber authenticated username password]
[-setgopherproxystate networkservice on | off]

[-getsocksfirewallproxy networkservice]
[-setsocksfirewallproxy networkservice domain portnumber authenticated username password]
[-setsocksfirewallproxystate networkservice on | off]

使用示例：

[-getsocksfirewallproxy networkservice]
[-setsocksfirewallproxy networkservice domain portnumber authenticated username password]
[-setsocksfirewallproxystate networkservice on | off]

---

设置忽略这些主机与域的代理设置

[-getproxybypassdomains networkservice]
[-setproxybypassdomains networkservice domain1 [domain2] [...]]

[-getproxyautodiscovery networkservice]
[-setproxyautodiscovery networkservice on | off]

使用被动FTP模式

[-getpassiveftp networkservice]
[-setpassiveftp networkservice on | off]

使用示例：
1

$ networksetup -setwebproxy "Wi-Fi" 10.240.188.10 8080 

2

$ sudo networksetup -getproxybypassdomains "Wi-Fi"
$ networksetup -setproxybypassdomains "Wi-Fi"   *.local、169.254/16、10.24

3

$ networksetup -getpassiveftp "Wi-Fi"
Passive FTP: Off

---

airport

[-getairportnetwork device]
[-setairportnetwork device network [password]]
[-getairportpower device] 
[-setairportpower device on | off]

使用示例：
1

$ networksetup -getairportnetwork en0
Current Wi-Fi Network: MS480-5G

$ networksetup -getairportnetwork en1
en1 is not a Wi-Fi interface.
** Error: Error obtaining wireless information.

$ networksetup -setairportnetwork en0 WIFI_SSID_I_WANT_TO_JOIN WIFI_PASSWORD

---

preferredwirelessnetworks 首选网络

[-listpreferredwirelessnetworks hardwareport]
[-addpreferredwirelessnetworkatindex hardwareport network index securitytype [password]]
[-removepreferredwirelessnetwork hardwareport network]
[-removeallpreferredwirelessnetworks hardwareport]

使用示例：
列出来的都是什么鬼？。。。

$ networksetup -listpreferredwirelessnetworks en0
Preferred networks on en0:
	@PHICOMM_48
	@PHICOMM_480
	TP-LINK_CED0
	MITEA
	久赞
	311
	老北京饺子馆
	xiaocuzi
	帝曼斯
	多喜爱面馆
	欢迎光临
	NJTY
	xiaomi007
	10D2
	iOS测试机
	麦客披萨
	茶博会
	探鱼Tanyu
	LEGEND FITNESS
	HoneyMoon_TeaRoom
	haoyun
	qfang
	滋补皇
	WUMU

---

networkserviceenabled

[-getnetworkserviceenabled networkservice]
[-setnetworkserviceenabled networkservice on | off]
[-createnetworkservice networkservicename hardwareport]
[-renamenetworkservice networkservice newnetworkservicename]
[-getdnsservers networkservice newnetworkservicename]
[-removenetworkservice networkservice]
[-ordernetworkservices service1 [service2] [service3] [...]]

使用示例：

$ networksetup -getnetworkserviceenabled "Wi-Fi"
Enabled

$ networksetup -getnetworkserviceenabled en0
en0 is not a recognized network service.
** Error: The parameters were not valid.

$ networksetup -duplicatenetworkservice "Built-In Ethernet" "Local LAN"

---

MTU

[-getMTU hardwareport] 
[-setMTU hardwarePort value]
[-listvalidMTUrange hardwareport] 

使用示例：

$ networksetup -getMTU en0
Active MTU: 1500 (Current Setting: 1500)

$ networksetup -getMTU "Wi-Fi"
Active MTU: 1500 (Current Setting: 1500)

$ networksetup -setMTU en0 1500

---

media

[-getmedia hardwareport]
[-setmedia hardwareport subtype [option1] [option2] [...]]
[-listvalidmedia hardwareport]

使用示例：

$ networksetup -getmedia en0
Current: autoselect
Active: autoselect

$ networksetup -setMedia en0 autoselect

$ networksetup -setMedia en0 100baseTX half-duplex

$ networksetup -listvalidmedia en0
autoselect

---

VLAN

[-createVLAN name parentdevice tag]
[-deleteVLAN name parentdevice tag] [-listVLANs]
[-listdevicesthatsupportVLAN] 
[-isBondSupported device]
[-createBond name [device1] [device2] [...]] [-deleteBond bond]
[-addDeviceToBond device bond]
[-removeDeviceFromBond device bond] [-listBonds]
[-showBondStatus bond] 

使用示例：

$ networksetup -createBond MyBond en0 en1

$ networksetup -addDeviceToBond en0 bond0

---

bond

[-isBondSupported device]
[-createBond name[device1][device2][...]]
[-deleteBond bond]
[-addDeviceToBond device bond]
[-removeDeviceFromBond device bond][-listBonds]
[-showBondStatus bond]

---

pppoe

[-listpppoeservices]
[-showpppoestatus name]
[-createpppoeservice device name account password [pppoeName]]
[-deletepppoeservice service]           

使用示例：

$ networksetup -setpppoepassword MyPPPoE - < ~/Desktop/MyPasswordFile.txt

---

802.1X

[-import8021xProfiles service path]
[-export8021xProfiles service path yes | no]

[-export8021xUserProfiles path yes | no]
[-export8021xLoginProfiles service path yes | no]
[-export8021xSystemProfile service path yes | no]

使用示例：

$ networksetup -import8021xProfiles Ethernet "/Users/MyHome/Downloads/ExportedCon-
     figs.networkconnect"

---

tls

[-settlsidentityonsystemprofile service path passphrase]
[-settlsidentityonuserprofile profile path passphrase]

[-deletesystemprofile service]
[-deleteloginprofile service profile]
[-deleteuserprofile profile][-version][-help]
[-printcommands]

---

systemprofile

[-enablesystemprofile service on | off]
[-enableloginprofile service profile on | off]
[-enableuserprofile profile on | off]

---

location

[-getcurrentlocation]
[-createlocation location[populate]]
[-deletelocation location]
[-switchtolocation location]

---

profiles

[-listalluserprofiles]  //This command is no longer supported.
[-listloginprofiles service]//This command is no longer supported.

---

manual

 -listnetworkserviceorder
             Displays a list of network services in the order they are contacted for a connec-
             tion, along with the corresponding port and device for each. An asterisk (*) next to
             a service means the service is inactive.

-listallnetworkservices
             Displays a list of all the network services on the server's hardware ports. An
             asterisk (*) denotes that a network service is disabled.

-listallhardwareports
             Displays list of hardware ports with corresponding device name and ethernet address.

-detectnewhardware
             Detects new network hardware and creates a default network service on the hardware.
             
  -getmacaddress hardwareport
             Displays ethernet (or Wi-Fi) address for hardwareport or device specified.

-getcomputername
             Displays the computer name.

-setcomputername computername
             Sets computer name to . This name is used by AFP.

-getinfo networkservice
             Displays the IP address, subnet mask, router, and hardware address for the  that you specify.

-setmanual networkservice ip subnet router
             Set the TCP/IP configuration for  to manual with IP address set to
             , Subnet Mask set to , and Router address set to .

-setdhcp networkservice [clientid]
             Use this command to set the TCP/IP configuration for the specified 
             to use DHCP. The client ID is optional. Specify "Empty" for [clientid] to clear the
             DHCP client id.

-setbootp networkservice
             Use this command to set the TCP/IP configuration for the specified 
             to use BOOTP.

-setmanualwithdhcprouter networkservice ip
             Use this command to specify a manual IP address to use for DHCP for the specified
             .

-getadditionalroutes networkservice
             Use this command to display the list of additional IPv4 routes configured for the
             service.

-setadditionalroutes networkservice [dest1 mask1 gate1] [dest2 mask2 gate2] ... [destN maskN
             gateN]
             Use this command to set the list of IPv4 additional routes configured for the ser-
             vice. Each route is specified as a (destination address, subnet mask, gateway
             address) tuple. Specifying no tuples clears the list of routes.

-setv4off networkservice
             Use this command to turn IPv4 off on the specified .

-setv6off networkservice
             Use this command to turn IPv6 off on the specified .

 -setv6automatic networkservice
             Use this command to set IPv6 to get its addresses automatically for .

-setv6linklocal networkservice
             Use this command to set IPv6 to only use link local for .

-setv6manual ip prefixlength router
             Use this command to set IPv6 to get its addresses manually for .
             Specify the ip address, the prefix length and the router.

-getv6additionalroutes networkservice
             Use this command to display the list of additional IPv6 routes configured for the
             service.

-setv6additionalroutes networkservice [dest1 prefixlength1 gate1] [dest2 prefixlength2
             gate2] ... [destN prefixlengthN gateN]
             Use this command to set the list of additional routes configured for the service.
             Each route is specified as a
             (destination address, prefix length, gateway address) tuple. Specifying no tuples
             clears the list of routes.

-getdnsservers networkservice
             Displays DNS info for .

-setdnsservers networkservice dns1 [dns2] [...]
             Use this command to specify the IP addresses of servers you want the specified  to use to resolve domain names. You can list any number of servers
             (replace dns1, dns2, and so on with the IP addresses of domain name servers). If you
             want to clear all DNS entries for the specified network service, type "empty" in
             place of the DNS server names.

-getsearchdomains networkservice
             Displays Domain Name info for .

-setsearchdomains networkservice domain1 [domain2] [...]
             Use this command to designate the search domain for the specified .
             You can list any number of search domains (replace domain1, domain2, and so on with
             the name of a local domain). If you want to clear all search domain entries for the
             specified network service, type aemptya in place of the domain name.



-create6to4service -
             Use this command to create a new 6 to 4 service with name .

-set6to4automatic -
             Use this command to set the 6 to 4 service such that it will get the relay address
             automatically.

-set6to4manual - -
             Use this command to set the 6 to 4 service such that it will get the relay address
             manually. Specify the  that you would like to set.

-getftpproxy networkservice
             Displays FTP proxy (server, port, enabled value) info for .

-setftpproxy networkservice domain portnumber authenticated username password
             Set FTP proxy for  with  and . Turns proxy on.
             Optionally, specify  or  for  to enable and disable authen-
             ticated proxy support. Specify  and  if you turn authenticated
             proxy support on.

-setftpproxystate networkservice on | off
             Set FTP proxy on  to either  or .

-getwebproxy networkservice
             Displays Web proxy (server, port, enabled value) info for .

-setwebproxy networkservice domain portnumber authenticated username password
             Set Web proxy for  with  and . Turns proxy on.
             Optionally, specify  or  for  to enable and disable authen-
             ticated proxy support. Specify  and  if you turn authenticated
             proxy support on.

-setwebproxystate networkservice on | off
             Set Web proxy on  to either  or .

-getsecurewebproxy networkservice
             Displays Secure Web proxy (server, port, enabled value) info for .

-setsecurewebproxy networkservice domain portnumber authenticated username password
             Set Secure Web proxy for  with  and . Turns
             proxy on. Optionally, specify  or  for  to enable and dis-
             able authenticated proxy support. Specify  and  if you turn
             authenticated proxy support on.

-setsecurewebproxystate networkservice on | off
             Set SecureWeb proxy on  to either  or .
             
-setstreamingproxy networkservice domain portnumber authenticated username password
             Set Streaming proxy for  with . Turns proxy on.
             Optionally, specify  or  for  to enable and disable authen-
             ticated proxy support. Specify  and  if you turn authenticated
             proxy support on.

-setstreamingproxystate networkservice on | off
             Set Streamingproxy on  to either  or .

-getgopherproxy networkservice
             Displays Gopher proxy (server, port, enabled value) info for .

-setgopherproxy networkservice domain portnumber authenticated username password
             Set Gopher proxy for  with  and . Turns proxy
             on. Optionally, specify  or  for  to enable and disable
             authenticated proxy support. Specify  and  if you turn authenti-
             cated proxy support on.

-setgopherproxystate networkservice on | off
             Set Gopher proxy on  to either  or .

-getsocksfirewallproxy networkservice
             Displays SOCKS Firewall proxy (server, port, enabled value) info for .

-setsocksfirewallproxy networkservice domain portnumber authenticated username password
             Set SOCKS Firewall proxy for  with  and . Turns
             proxy on. Optionally, specify  or  for  to enable and dis-
             able authenticated proxy support. Specify  and  if you turn
             authenticated proxy support on.

-setsocksfirewallproxystate networkservice on | off
             Set SOCKS Firewall proxy to  either  or .

-getproxybypassdomains networkservice
             Displays Bypass Domain Names for .

-setproxybypassdomains networkservice domain1 [domain2] [...]
             Set the Bypass Domain Name Servers for  to  [domain2]
             [...]. Any number of Domain Name servers can be specified. Specify "Empty" for
              to clear all Domain Name entries.

-getproxyautodiscovery networkservice
             Displays Proxy Auto Discover for .

 -getpassiveftp networkservice
             Displays whether Passive FTP is on or off for .

-setpassiveftp networkservice on | off
             Set Passive FTP to either  or .

-setautoproxyurl networkservice url
             Set proxy auto-config to url for  and enable it.

-getautoproxyurl networkservice
             Displays proxy auto-config (url, enabled) info for .

-setsocksfirewallproxystate networkservice on | off
             Set SOCKS Firewall proxy to  either  or .

-getairportnetwork hardwareport
             Displays current Wi-Fi Network.

-setairportnetwork hardwareport network [password]
             Set Wi-Fi Network to  using optional [password] if specified.

-getairportpower hardwareport
             Displays whether Wi-Fi power is on or off.

-setairportpower hardwareport on | off
             Set Wi-Fi power to either  or .

-listpreferredwirelessnetworks hardwareport
             List the preferred wireless networks for 

-addpreferredwirelessnetworkatindex hardwareport network index securitytype [password]
             Add wireless network named  to preferred list for  at
             . Store the optional password in the keychain For security type, use OPEN for
             none, WPA for WPA Personal, WPA2 for WPA2 Personal, WPA/WPA2 for WPA/WPA2 Personal,
             WPAE for WPA Enterprise, WPA2E for WPA2 Enterprise, WPAE/WPA2E for WPA/WPA2 Enter-
             prise, WEP for plain WEP, and 8021XWEP for 802.1X WEP.
             
-removepreferredwirelessnetwork hardwareport network
             Remove  from the preferred wireless network list for 

-removeallpreferredwirelessnetworks hardwareport
             Remove all networks from the preferred wireless network list for 

-getnetworkserviceenabled networkservice
             Displays whether a service is on or off (enabled or disabled).

-setnetworkserviceenabled networkservice on | off
             Use this command to turn the specified network service on or off (enable or dis-
             able).

-createnetworkservice networkservicename hardwareport
             Create a service named  on port . The new service will
             be enabled by default.

-renamenetworkservice networkservice newnetworkservicename
             Use this command to rename the specified network service  to
             .

-duplicatenetworkservice networkservice newnetworkservicename
             Use this command to duplicate an existing network service  and
             rename it to the specified name .

-removenetworkservice networkservice
             Use this command to delete a network service . You cannot use this
             command to delete the last remaining service for a hardware port. To do so, you use
             the -setnetworkserviceenabled command.

-ordernetworkservices service1 [service2] [service3] [...]
             Use this command to designate the order network services are contacted on the speci-
             fied hardware port. Name the network you want contacted first, then the second, and
             so on. Use "listnetworkserviceorder" to view current service order. Note: use quotes
             around service names which contain spaces (ie. "Built-in Ethernet").

-setMTUAndMediaAutomatically hardwarePort
             Set hardwareport or device specified back to automatically setting the MTU and
             Media.

-getMTU hardwareport
             Get the MTU value for hardwareport or device specified.

-setMTU hardwarePort value
             Set MTU for hardwareport or device specified.
             
-listValidMTURange hardwareport
             List the valid MTU range for hardwareport or device specified.

-getMedia hardwareport
             Show both the current setting for media and the active media on hardwareport or
             device specified.

-setMedia hardwareport subtype [option1] [option2] [...]
             Set media for hardwareport or device specified to subtype. Specify optional
             [option1] and additional options depending on subtype. Any number of valid options
             can be specified.

-listValidMedia hardwareport
             List valid media options for hardwareport or device name. Enumerates available sub-
             types and options per subtype.

-createVLAN name parentdevice tag
             Create a VLAN with the name  over the parent device  and with
             the tag .

-deleteVLAN name parentdevice tag
             Delete the VLAN with the name  over the parent device  and with
             the tag .

-listVLANs
             List the VLANs that have been created.

-listdevicesthatsupportVLAN
             List the devices that support VLANs.

-isBondSupported device
             Displays YES if the device can be added to a bond. NO if it cannot.

-createBond name [device1] [device2] [...]
             Create a bond with the user-defined-name name and optionally add any listed devices
             if they support bonding.

-deleteBond bond
             Delete the bond with the specified device-name.

-addDeviceToBond device bond
             Add device to bond.

-removeDeviceFromBond device bond
             Remove device from bond.

-listBonds
             List of all bonds.

-showBondStatus bond
             Display the status of the specified bond.

-listpppoeservices
             List all PPPoE services in the current set.

-showpppoestatus name
             Display the status of the PPPoE service with the specified name.

-createpppoeservice device name account password [pppoeName]
             Create a PPPoE service on the specified device with the service name specified.

-deletepppoeservice service
             Delete the service.

-setpppoeaccountname service account
             Set the account name for the service.

-setpppoepassword service password
             Set the password for the service.

-connectpppoeservice service
             Connect the service.

-disconnectpppoeservice service
             Disconnect the service.
             
-listlocations
             List all network locations.

-getcurrentlocation
             Display the name of the current set.

-createlocation location [populate]
             Create a set with the user-defined-name name and optionally populate it with the
             default services.

-deletelocation location
             Delete the set.

-switchtolocation location
             Make the specified set the current set.

-listalluserprofiles
             Display the names of all of the user profiles.

-listloginprofiles service
             Display the names of the loginwindow profiles for the specified service.

-enablesystemprofile service on | off
             Enables or disables the system profile for the specified service.

-enableloginprofile service profile on | off
             Enables or disables the specified loginwindow profile for the specified ser-
             vice.

-enableuserprofile profile on | off
             Enables or disables the specified user profile.

-import8021xProfiles service path
             Imports the 802.1x profiles for the specified service.


-export8021xProfiles service path yes | no
             Exports all of the profiles for the specified service and optionally includes the
             items from the keychain.

-export8021xUserProfiles path yes | no
             Exports only the user profiles and optionally includes the items from the key-
             chain.
             
-export8021xLoginProfiles service path yes | no
             Exports only the loginwindow profiles for the specified service  and optionally
             includes the items from the keychain.

-export8021xSystemProfile service path yes | no
             Exports only the system profile for the specified service and optionally includes
             the items from the keychain.

-settlsidentityonsystemprofile service path passphrase
             Sets the TLS identity on the system profile for the specified service. Identity must
             be a pkcs12 file.

-settlsidentityonuserprofile profile path passphrase
             Sets the TLS identity on the specified user profile. Identity must be a pkcs12 file.

-deletesystemprofile service
             Deletes the system profile for the specified service.

-deleteloginprofile service profile
             Deletes the specified loginwindow profile for the specified service.

-deleteuserprofile profile
             Deletes the specified user profile.  Displays version of networksetup tool.

-help   Displays a list of all the commands available in the Network Setup Tool, with
             explanatory information.

-printcommands
             Displays a list of commands with no detail.
-isBondSupported device
             Displays YES if the device can be added to a bond. NO if it cannot.

-createBond name [device1] [device2] [...]
             Create a bond with the user-defined-name name and optionally add any listed devices
             if they support bonding.

-deleteBond bond
             Delete the bond with the specified device-name.

-addDeviceToBond device bond
             Add device to bond.

-removeDeviceFromBond device bond
             Remove device from bond.

---