centos7.6升级openssh9.3p1,openssl1.1.1t

一、安装前查看系统及版本

# cat /etc/redhat-release 
CentOS Linux release 7.2.1511 (Core) 
# ssh -V
OpenSSH_6.6.1p1, OpenSSL 1.0.1e-fips 11 Feb 2013

二、安装步骤
1.下载tar包

​wget https://www.openssl.org/source/openssl-1.1.1t.tar.gz --no-check-certificate
wget https://cdn.openbsd.org/pub/OpenBSD/OpenSSH/portable/openssh-9.3p1.tar.gz 
wget http://www.zlib.net/zlib-1.2.13.tar.gz

解压到指定路径：

tar zxvf openssl-1.1.1t.tar.gz -C /usr/local/src/
tar zxvf openssh-9.3p1.tar.gz -C /usr/local/src/
tar zxvf zlib-1.2.13.tar.gz -C /usr/local/src 

2.安装相关依赖和gcc编译工具

yum -y install gcc gcc-c++ kernel-devel
yum -y install pam pam-devel zlib zlib-devel

3.安装zlib

cd /usr/local/src/zlib-1.2.13/
./configure --prefix=/usr/local/zlib && make -j 4 && make install

4.安装openssl

​cd /usr/local/src/openssl-1.1.1t/
./config --prefix=/usr/local/ssl -d shared

make -j 4 && make install
echo '/usr/local/ssl/lib' >> /etc/ld.so.conf
ldconfig -v

5.安装openssh

mv /etc/ssh /etc/ssh.bak
cd /usr/local/src/openssh-9.3p1/
./configure --prefix=/usr/local/openssh --sysconfdir=/etc/ssh --with-ssl-dir=/usr/local/ssl --with-zlib=/usr/local/zlib 

make -j 4 && make install

6.修改配置文件
（1）sshd_config文件修改

echo "X11Forwarding yes" >> /etc/ssh/sshd_config
echo "X11UseLocalhost no" >> /etc/ssh/sshd_config
echo "#XAuthLocation /usr/bin/xauth" >> /etc/ssh/sshd_config
echo "UseDNS no" >> /etc/ssh/sshd_config
echo 'PermitRootLogin yes' >> /etc/ssh/sshd_config
echo 'PubkeyAuthentication yes' >> /etc/ssh/sshd_config
echo 'PasswordAuthentication yes' >> /etc/ssh/sshd_config

需要添加X11Forwarding yes开启X11转发，调用图形界面，如oracle安装等操作需要图形界面
***必须添加X11UseLocalhost no 和 XAuthLocation /usr/bin/xauth 这两项，否则X11转发不好使
验证X11转发是否好使，xhost + 出现下面的是可以正常使用的

（2） 备份 /etc/ssh 原有文件，并将新的配置复制到指定目录

mv /usr/sbin/sshd /usr/sbin/sshd.bak
cp -rf /usr/local/openssh/sbin/sshd /usr/sbin/sshd
mv /usr/bin/ssh /usr/bin/ssh.bak
cp -rf /usr/local/openssh/bin/ssh /usr/bin/ssh 
mv /usr/bin/ssh-keygen /usr/bin/ssh-keygen.bak
cp -rf /usr/local/openssh/bin/ssh-keygen /usr/bin/ssh-keygen

安装完成，查看版本ssh -V

# ssh -V
OpenSSH_9.3p1, OpenSSL 1.1.1t  7 Feb 2023

7.启动sshd

systemctl restart sshd

开机自启

systemctl enable sshd 

9.天翼云服务器启动sshd问题

拷贝系统启动文件

cp /usr/local/src/openssh-9.3p1/contrib/redhat/sshd.init /etc/init.d/sshd

把原先的systemd管理的sshd文件移走，不然影响重启sshd服务

mv  /usr/lib/systemd/system/sshd.service /usr/lib/systemd/system/sshd.service.bak
systemctl daemon-reload

将sshd添加到系统服务

chkconfig --add sshd
chkconfig sshd on

# chkconfig --list

Note: This output shows SysV services only and does not include native
      systemd services. SysV configuration data might be overridden by native
      systemd configuration.

      If you want to list systemd services use 'systemctl list-unit-files'.
      To see services enabled on particular target use
      'systemctl list-dependencies [target]'.

denyhosts       0:on    1:on    2:on    3:on    4:on    5:on    6:on
netconsole      0:off   1:off   2:off   3:off   4:off   5:off   6:off
network         0:off   1:off   2:off   3:off   4:off   5:off   6:off
sshd            0:off   1:off   2:on    3:on    4:on    5:on    6:off

重启sshd

service sshd status
service sshd restart

10.注意
注意：升级后由于加密算法的区别，低版本的SSH工具可能无法连接，建议改用Xshell7或SecureCRT9.0以上版本。