FFT64点傅里叶变换verilog蝶形运算，代码和视频
名称：FFT64点verilog傅里叶变换
软件：Quartus
语言：Verilog
代码功能：
使用verilog代码实现64点FFT变换，使用蝶形运算实现傅里叶变换
演示视频：http://www.hdlcode.com/index.php?m=home&c=View&a=index&aid=208
FPGA代码资源下载网：hdlcode.com
代码下载：
软件：Quartus 语言：Verilog 代码功能： 使用verilog代码实现64点FFT变换，使用蝶形运算实现傅里叶变换名称：FFT64点verilog傅里叶变换（代码在文末付费下载）软件：Quartus语言：Verilog代码功能： 使用verilog代码实现64点FFT变换，使用蝶形运算实现傅里叶变换演示视频：FPGA代码资源下载网：hdlcode.com部分代码展示`timescale 1ns / 1ps//64点FFTmodule top(input clk, input rst, input [
http://www.hdlcode.com/index.php?m=home&c=View&a=index&aid=208
部分代码展示
`timescale 1ns / 1ps
//64点FFT
module top(input clk,
input rst,
input [7:0] data_in_r,
input [7:0] data_in_i,
input data_in_ready,
output [19:0] data_out_r,
output [19:0] data_out_i,
output reg data_out_ready
);
wire working;
reg [5:0] count;
reg [5:0] count_out;
reg flag;
reg working_flag_0;
reg working_flag_1;
reg working_flag_2;
reg working_flag_3;
reg working_flag_4;
reg working_flag_5;
reg working_flag_6;
reg working_flag_7;
assign working = data_in_ready || working_flag_1;
always @(posedge clk)
begin
if(rst)
begin
count<=6'd0;
end
else
begin
if(!data_in_ready)
count<=6'd0;
else
begin
if(count < 6'd63)
count<=count+6'b1;
else
count <= count;
end
end
end
always@(posedge clk)
begin
if(rst)
working_flag_0 <= 0;
else
if(working && working_flag_1 == 0)
working_flag_0 <= 1;
else
working_flag_0 <= 0;
end
always@(posedge clk)
begin
if(rst)
flag <= 0;
else
if(count == 6'd62 && flag == 0)
flag <= 1;
else
flag <= 0;
end
always@(posedge clk)
begin
if(rst)
working_flag_1 <= 0;
else
if(count == 6'd63 && flag == 1)
working_flag_1 <= 1;
else
working_flag_1 <= 0;
end
always@(posedge clk)
begin
if(rst)
working_flag_2 <= 0;
else
if(working_flag_1)
working_flag_2 <= 1;
else
working_flag_2 <= 0;
end
always@(posedge clk)
begin
if(rst)
working_flag_3 <= 0;
else
if(working_flag_2)
working_flag_3 <= 1;
else
working_flag_3 <= 0;
end
always@(posedge clk)
begin
if(rst)
working_flag_4 <= 0;
else
if(working_flag_3)
working_flag_4 <= 1;
else
working_flag_4 <= 0;
end
always@(posedge clk)
begin
if(rst)
working_flag_5 <= 0;
else
if(working_flag_4)
working_flag_5 <= 1;
else
working_flag_5 <= 0;
end
always@(posedge clk)
begin
if(rst)
working_flag_6 <= 0;
else
if(working_flag_5)
working_flag_6 <= 1;
else
working_flag_6 <= 0;
end
always@(posedge clk)
begin
if(rst)
working_flag_7 <= 0;
else
if(working_flag_6)
working_flag_7 <= 1;
else
if(count_out < 6'd63 && working_flag_7 == 1)
working_flag_7 <= 1;
else
working_flag_7 <= 0;
end
always@(posedge clk)
begin
if(rst)
count_out <= 0;
else
if(working_flag_6)
count_out <= 0;
else
if(count_out < 6'd63)
count_out <= count_out + 1;
else
count_out <= 0;
end
always@(posedge clk)
begin
if(rst)
data_out_ready <= 0;
else
if(working_flag_7 == 1 && data_out_ready == 0)
data_out_ready <= 1;
else
if(count_out < 6'd63)
data_out_ready <= data_out_ready;
else
data_out_ready <= 6'b0;
end
wire [15:0] data_in_r_15;
wire [15:0] data_in_i_15;
assign data_in_r_15={data_in_r[7],data_in_r[7],data_in_r[7],data_in_r[7],data_in_r[7],data_in_r[7],data_in_r[7],data_in_r[7],data_in_r};
assign data_in_i_15={data_in_i[7],data_in_i[7],data_in_i[7],data_in_i[7],data_in_i[7],data_in_i[7],data_in_i[7],data_in_i[7],data_in_i};
butterfly butterfly(.clk(clk),
.rst(rst),
.data_in_r(data_in_r_15),
.data_in_i(data_in_i_15),
.count(count),
.count_out(count_out),
.working_flag_0(working_flag_0),
.working_flag_1(working_flag_1),
.working_flag_2(working_flag_2),
.working_flag_3(working_flag_3),
.working_flag_4(working_flag_4),
.working_flag_5(working_flag_5),
.working_flag_6(working_flag_6),
.working_flag_7(working_flag_7),
.data_out_r(data_out_r),
.data_out_i(data_out_i)
);
endmodule
设计文档：
64点fft设计.doc
1.工程文件
2. 程序文件
3.Testbench
4.modelsim仿真图
