【转】Android音频系统相关术语解释说明

【说明】

    本文转载自Android官网文章《Audio Terminology》，以备不可的时候查阅。

【正文】

Audio Terminology

IN THIS DOCUMENT

1. Generic Terms
   1. Digital Audio
   2. Inter-device interconnect
   3. Intra-device interconnect
   4. Audio Signal Path
   5. Sample Rate Conversion
2. Android-Specific Terms

This glossary of audio-related terminology includes widely-used generic terms and Android-specific terms.

Generic Terms

---

Generic audio-related terms have conventional meanings.

Digital Audio

Digital audio terms relate to handling sound using audio signals encoded in digital form. For details, refer to Digital Audio.

acoustics

Study of the mechanical properties of sound, such as how the physical placement of transducers (speakers, microphones, etc.) on a device affects perceived audio quality.

attenuation

Multiplicative factor less than or equal to 1.0, applied to an audio signal to decrease the signal level. Compare to  gain.

audiophile

Person concerned with a superior music reproduction experience, especially willing to make substantial tradeoffs (expense, component size, room design, etc.) for sound quality. For details, refer to  audiophile.

bits per sample or bit depth

Number of bits of information per sample.

channel

Single stream of audio information, usually corresponding to one location of recording or playback.

downmixing

Decrease the number of channels, such as from stereo to mono or from 5.1 to stereo. Accomplished by dropping channels, mixing channels, or more advanced signal processing. Simple mixing without attenuation or limiting has the potential for overflow and clipping. Compare to  upmixing.

DSD

Direct Stream Digital. Proprietary audio encoding based on  pulse-density modulation. While Pulse Code Modulation (PCM) encodes a waveform as a sequence of individual audio samples of multiple bits, DSD encodes a waveform as a sequence of bits at a very high sample rate (without the concept of samples). Both PCM and DSD represent multiple channels by independent sequences. DSD is better suited to content distribution than as an internal representation for processing as it can be difficult to apply traditional digital signal processing (DSP) algorithms to DSD. DSD is used in  Super Audio CD (SACD) and in DSD over PCM (DoP) for USB. For details, refer to  Digital Stream Digital.

duck

Temporarily reduce the volume of a stream when another stream becomes active. For example, if music is playing when a notification arrives, the music ducks while the notification plays. Compare to  mute.

FIFO

First In, First Out. Hardware module or software data structure that implements  First In, First Out queueing of data. In an audio context, the data stored in the queue are typically audio frames. FIFO can be implemented by a  circular buffer.

frame

Set of samples, one per channel, at a point in time.

frames per buffer

Number of frames handed from one module to the next at one time. The audio HAL interface uses the concept of frames per buffer.

gain

Multiplicative factor greater than or equal to 1.0, applied to an audio signal to increase the signal level. Compare to  attenuation.

HD audio

High-Definition audio. Synonym for high-resolution audio (but different than Intel High Definition Audio).

Hz

Units for sample rate or frame rate.

high-resolution audio

Representation with greater bit-depth and sample rate than CDs (stereo 16-bit PCM at 44.1 kHz) and without lossy data compression. Equivalent to HD audio. For details, refer to  high-resolution audio.

latency

Time delay as a signal passes through a system.

lossless

A  lossless data compression algorithm that preserves bit accuracy across encoding and decoding, where the result of decoding previously encoded data is equivalent to the original data. Examples of lossless audio content distribution formats include  CDs, PCM within  WAV, and  FLAC. The authoring process may reduce the bit depth or sample rate from that of the  masters; distribution formats that preserve the resolution and bit accuracy of masters are the subject of high-resolution audio.

lossy

A  lossy data compression algorithm that attempts to preserve the most important features of media across encoding and decoding where the result of decoding previously encoded data is perceptually similar to the original data but not identical. Examples of lossy audio compression algorithms include MP3 and AAC. As analog values are from a continuous domain and digital values are discrete, ADC and DAC are lossy conversions with respect to amplitude. See also  transparency.

mono

One channel.

multichannel

See  surround sound. In strict terms,  stereo is more than one channel and could be considered multichannel; however, such usage is confusing and thus avoided.

mute

Temporarily force volume to be zero, independent from the usual volume controls.

overrun

Audible  glitch caused by failure to accept supplied data in sufficient time. For details, refer to  buffer underrun. Compare to  underrun.

panning

Direct a signal to a desired position within a stereo or multichannel field.

PCM

Pulse Code Modulation. Most common low-level encoding of digital audio. The audio signal is sampled at a regular interval, called the sample rate, then quantized to discrete values within a particular range depending on the bit depth. For example, for 16-bit PCM the sample values are integers between -32768 and +32767.

ramp

Gradually increase or decrease the level of a particular audio parameter, such as the volume or the strength of an effect. A volume ramp is commonly applied when pausing and resuming music to avoid a hard audible transition.

sample

Number representing the audio value for a single channel at a point in time.

sample rate or frame rate

Number of frames per second. While  frame rate is more accurate,  sample rate is conventionally used to mean frame rate.

sonification

Use of sound to express feedback or information, such as touch sounds and keyboard sounds.

stereo

Two channels.

stereo widening

Effect applied to a stereo signal to make another stereo signal that sounds fuller and richer. The effect can also be applied to a mono signal, where it is a type of upmixing.

surround sound

Techniques for increasing the ability of a listener to perceive sound position beyond stereo left and right.

transparency

Ideal result of lossy data compression. Lossy data conversion is transparent if it is perceptually indistinguishable from the original by a human subject. For details, refer to  Transparency.

underrun

Audible  glitch caused by failure to supply needed data in sufficient time. For details, refer to  buffer underrun. Compare to  overrun.

upmixing

Increase the number of channels, such as from mono to stereo or from stereo to surround sound. Accomplished by duplication, panning, or more advanced signal processing. Compare to  downmixing.

virtualizer

Effect that attempts to spatialize audio channels, such as trying to simulate more speakers or give the illusion that sound sources have position.

volume

Loudness, the subjective strength of an audio signal.

Inter-device interconnect

Inter-device interconnection technologies connect audio and video components between devices and are readily visible at the external connectors. The HAL implementer and end user should be aware of these terms.

Bluetooth

Short range wireless technology. For details on the audio-related  Bluetooth profiles and  Bluetooth protocols, refer to  A2DP for music,  SCO for telephony, and  Audio/Video Remote Control Profile (AVRCP).

DisplayPort

Digital display interface by the Video Electronics Standards Association (VESA).

dongle

A  dongle is a small gadget, especially one that hangs off another device.

HDMI

High-Definition Multimedia Interface. Interface for transferring audio and video data. For mobile devices, a micro-HDMI (type D) or MHL connector is used.

Intel HDA

Intel High Definition Audio (do not confuse with generic  high-definition audio or  high-resolution audio). Specification for a front-panel connector. For details, refer to  Intel High Definition Audio.

interface

An  interface converts a signal from one representation to another. Common interfaces include a USB audio interface and MIDI interface.

line level

Line level is the strength of an analog audio signal that passes between audio components, not transducers.

MHL

Mobile High-Definition Link. Mobile audio/video interface, often over micro-USB connector.

phone connector

Mini or sub-mini component that connects a device to wired headphones, headset, or line-level amplifier.

SlimPort

Adapter from micro-USB to HDMI.

S/PDIF

Sony/Philips Digital Interface Format. Interconnect for uncompressed PCM. For details, refer to  S/PDIF. S/PDIF is the consumer grade variant of  AES3.

Thunderbolt

Multimedia interface that competes with USB and HDMI for connecting to high-end peripherals. For details, refer to  Thunderbolt.

TOSLINK

TOSLINK is an optical audio cable used with  S/PDIF.

USB

Universal Serial Bus. For details, refer to  USB.

Intra-device interconnect

Intra-device interconnection technologies connect internal audio components within a given device and are not visible without disassembling the device. The HAL implementer may need to be aware of these, but not the end user. For details on intra-device interconnections, refer to the following articles:

• GPIO
• I²C, for control channel
• I²S, for audio data, simpler than SLIMbus
• McASP
• SLIMbus
• SPI
• AC'97
• Intel HDA
• SoundWire

In ALSA System on Chip (ASoC), these are collectively called Digital Audio Interfaces (DAI).

Audio Signal Path

Audio signal path terms relate to the signal path that audio data follows from an application to the transducer or vice-versa.

ADC

Analog-to-digital converter. Module that converts an analog signal (continuous in time and amplitude) to a digital signal (discrete in time and amplitude). Conceptually, an ADC consists of a periodic sample-and-hold followed by a quantizer, although it does not have to be implemented that way. An ADC is usually preceded by a low-pass filter to remove any high frequency components that are not representable using the desired sample rate. For details, refer to  Analog-to-digital converter.

AP

Application processor. Main general-purpose computer on a mobile device.

codec

Coder-decoder. Module that encodes and/or decodes an audio signal from one representation to another (typically analog to PCM or PCM to analog). In strict terms,  codec is reserved for modules that both encode and decode but can be used loosely to refer to only one of these. For details, refer to  Audio codec.

DAC

Digital-to-analog converter. Module that converts a digital signal (discrete in time and amplitude) to an analog signal (continuous in time and amplitude). Often followed by a low-pass filter to remove high-frequency components introduced by digital quantization. For details, refer to  Digital-to-analog converter.

DSP

Digital Signal Processor. Optional component typically located after the application processor (for output) or before the application processor (for input). Primary purpose is to off-load the application processor and provide signal processing features at a lower power cost.

PDM

Pulse-density modulation. Form of modulation used to represent an analog signal by a digital signal, where the relative density of 1s versus 0s indicates the signal level. Commonly used by digital to analog converters. For details, refer to  Pulse-density modulation.

PWM

Pulse-width modulation. Form of modulation used to represent an analog signal by a digital signal, where the relative width of a digital pulse indicates the signal level. Commonly used by analog-to-digital converters. For details, refer to  Pulse-width modulation.

transducer

Converts variations in physical real-world quantities to electrical signals. In audio, the physical quantity is sound pressure, and the transducers are the loudspeaker and microphone. For details, refer to  Transducer.

Sample Rate Conversion

Sample rate conversion terms relate to the process of converting from one sampling rate to another.

downsample

Resample, where sink sample rate < source sample rate.

Nyquist frequency

Maximum frequency component that can be represented by a discretized signal at 1/2 of a given sample rate. For example, the human hearing range extends to approximately 20 kHz, so a digital audio signal must have a sample rate of at least 40 kHz to represent that range. In practice, sample rates of 44.1 kHz and 48 kHz are commonly used, with Nyquist frequencies of 22.05 kHz and 24 kHz respectively. For details, refer to  Nyquist frequency and  Hearing range.

resampler

Synonym for sample rate converter.

resampling

Process of converting sample rate.

sample rate converter

Module that resamples.

sink

Output of a resampler.

source

Input to a resampler.

upsample

Resample, where sink sample rate > source sample rate.

Android-Specific Terms

---

Android-specific terms include terms used only in the Android audio framework and generic terms that have special meaning within Android.

ALSA

Advanced Linux Sound Architecture. An audio framework for Linux that has also influenced other systems. For a generic definition, refer to  ALSA. In Android, ALSA refers to the kernel audio framework and drivers and not to the user-mode API. See also  tinyalsa.

audio device

Audio I/O endpoint backed by a HAL implementation.

AudioEffect

API and implementation framework for output (post-processing) effects and input (pre-processing) effects. The API is defined at  android.media.audiofx.AudioEffect.

AudioFlinger

Android sound server implementation. AudioFlinger runs within the mediaserver process. For a generic definition, refer to  Sound server.

audio focus

Set of APIs for managing audio interactions across multiple independent apps. For details, see  Managing Audio Focus and the focus-related methods and constants of  android.media.AudioManager.

AudioMixer

Module in AudioFlinger responsible for combining multiple tracks and applying attenuation (volume) and effects. For a generic definition, refer to  Audio mixing (recorded music) (discusses a mixer as a hardware device or software application, rather than a software module within a system).

audio policy

Service responsible for all actions that require a policy decision to be made first, such as opening a new I/O stream, re-routing after a change, and stream volume management.

AudioRecord

Primary low-level client API for receiving data from an audio input device such as a microphone. The data is usually PCM format. The API is defined at  android.media.AudioRecord.

AudioResampler

Module in AudioFlinger responsible for  sample rate conversion.

audio source

An enumeration of constants that indicates the desired use case for capturing audio input. For details, see  audio source. As of API level 21 and above,  audio attributes are preferred.

AudioTrack

Primary low-level client API for sending data to an audio output device such as a speaker. The data is usually in PCM format. The API is defined at  android.media.AudioTrack.

audio_utils

Audio utility library for features such as PCM format conversion, WAV file I/O, and  non-blocking FIFO, which is largely independent of the Android platform.

client

Usually an application or app client. However, an AudioFlinger client can be a thread running within the mediaserver system process, such as when playing media decoded by a MediaPlayer object.

HAL

Hardware Abstraction Layer. HAL is a generic term in Android; in audio, it is a layer between AudioFlinger and the kernel device driver with a C API (which replaces the C++ libaudio).

FastCapture

Thread within AudioFlinger that sends audio data to lower latency fast tracks and drives the input device when configured for reduced latency.

FastMixer

Thread within AudioFlinger that receives and mixes audio data from lower latency fast tracks and drives the primary output device when configured for reduced latency.

fast track

AudioTrack or AudioRecord client with lower latency but fewer features on some devices and routes.

MediaPlayer

Higher-level client API than AudioTrack. Plays encoded content or content that includes multimedia audio and video tracks.

media.log

AudioFlinger debugging feature available in custom builds only. Used for logging audio events to a circular buffer where they can then be retroactively dumped when needed.

mediaserver

Android system process that contains media-related services, including AudioFlinger.

NBAIO

Non-blocking audio input/output. Abstraction for AudioFlinger ports. The term can be misleading as some implementations of the NBAIO API support blocking. The key implementations of NBAIO are for different types of pipes.

normal mixer

Thread within AudioFlinger that services most full-featured AudioTrack clients. Directly drives an output device or feeds its sub-mix into FastMixer via a pipe.

OpenSL ES

Audio API standard by  The Khronos Group. Android versions since API level 9 support a native audio API that is based on a subset of  OpenSL ES 1.0.1.

silent mode

User-settable feature to mute the phone ringer and notifications without affecting media playback (music, videos, games) or alarms.

SoundPool

Higher-level client API than AudioTrack. Plays sampled audio clips. Useful for triggering UI feedback, game sounds, etc. The API is defined at  android.media.SoundPool.

Stagefright

See  Media.

StateQueue

Module within AudioFlinger responsible for synchronizing state among threads. Whereas NBAIO is used to pass data, StateQueue is used to pass control information.

strategy

Group of stream types with similar behavior. Used by the audio policy service.

stream type

Enumeration that expresses a use case for audio output. The audio policy implementation uses the stream type, along with other parameters, to determine volume and routing decisions. For a list of stream types, see  android.media.AudioManager.

tee sink

See  Audio Debugging.

tinyalsa

Small user-mode API above ALSA kernel with BSD license. Recommended for HAL implementations.

ToneGenerator

Higher-level client API than AudioTrack. Plays dual-tone multi-frequency (DTMF) signals. For details, refer to  Dual-tone multi-frequency signaling and the API definition at  android.media.ToneGenerator.

track

Audio stream. Controlled by the AudioTrack or AudioRecord API.

volume attenuation curve

Device-specific mapping from a generic volume index to a specific attenuation factor for a given output.

volume index

Unitless integer that expresses the desired relative volume of a stream. The volume-related APIs of android.media.AudioManager operate in volume indices rather than absolute attenuation factors.