mini2440-Openwrt启动信息

[    0.000000] Booting Linux on physical CPU 0x0

[    0.000000] Linux version 3.10.55 (hades@PandoraBox-Server) (gcc version 4.8.3 (PandoraBox/Linaro GCC 4.8-2014.04 svn-r127) ) #1 Thu Oct 9 17:19:46 CST 2014

[    0.000000] CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177

[    0.000000] CPU: VIVT data cache, VIVT instruction cache

[    0.000000] Machine: MINI2440

[    0.000000] Memory policy: ECC disabled, Data cache writeback

[    0.000000] CPU S3C2440A (id 0x32440001)

[    0.000000] S3C24XX Clocks, Copyright 2004 Simtec Electronics

[    0.000000] S3C244X: core 405.000 MHz, memory 101.250 MHz, peripheral 50.625 MHz

[    0.000000] CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on

[    0.000000] On node 0 totalpages: 16384

[    0.000000] free_area_init_node: node 0, pgdat 804227c8, node_mem_map 80472000

[    0.000000]   Normal zone: 128 pages used for memmap

[    0.000000]   Normal zone: 0 pages reserved

[    0.000000]   Normal zone: 16384 pages, LIFO batch:3

[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768

[    0.000000] pcpu-alloc: [0] 0 

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256

[    0.000000] Kernel command line: root=/dev/mtdblock3 console=ttySAC0,115200 rootfstype=squashfs,ext2

[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)

[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

[    0.000000] Memory: 64MB = 64MB total

[    0.000000] Memory: 60376k/60376k available, 5160k reserved, 0K highmem

[    0.000000] Virtual kernel memory layout:

[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)

[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)

[    0.000000]     vmalloc : 0x84800000 - 0xff000000   (1960 MB)

[    0.000000]     lowmem  : 0x80000000 - 0x84000000   (  64 MB)

[    0.000000]     modules : 0x7f000000 - 0x80000000   (  16 MB)

[    0.000000]       .text : 0x80008000 - 0x803f6d5c   (4028 kB)

[    0.000000]       .init : 0x803f7000 - 0x8041bd70   ( 148 kB)

[    0.000000]       .data : 0x8041c000 - 0x804442e4   ( 161 kB)

[    0.000000]        .bss : 0x804442e4 - 0x80471628   ( 181 kB)

[    0.000000] NR_IRQS:111

[    0.000000] S3C2440: IRQ Support

[    0.000000] irq: clearing pending status 02000000

[    0.000000] irq: clearing pending status 00000002

[    0.000000] sched_clock: 16 bits at 1012kHz, resolution 987ns, wraps every 64ms

[    0.000399] Calibrating delay loop... 201.52 BogoMIPS (lpj=503808)

[    0.044937] pid_max: default: 32768 minimum: 301

[    0.045349] Mount-cache hash table entries: 512

[    0.047546] CPU: Testing write buffer coherency: ok

[    0.049160] Setting up static identity map for 0x800101b0 - 0x80010210

[    0.005706] regulator-dummy: no parameters

[    0.007838] NET: Registered protocol family 16

[    0.010824] DMA: preallocated 256 KiB pool for atomic coherent allocations

[    0.038963] MINI2440: Option string mini2440=3tb

[    0.039042] MINI2440: 't' ignored, touchscreen not compiled in

[    0.039107] MINI2440: LCD 0:240x320 1:800x480 2:1024x768 [3:320x240]

[    0.064070] S3C2440: Initialising architecture

[    0.000894] S3C244X: Clock Support, DVS off

[    0.000977] S3C24XX DMA Driver, Copyright 2003-2006 Simtec Electronics

[    0.001249] DMA channel 0 at 84846000, irq 33

[    0.001307] DMA channel 1 at 84846040, irq 34

[    0.001327] DMA channel 2 at 84846080, irq 35

[    0.001347] DMA channel 3 at 848460c0, irq 36

[    0.008520] S3C24XX CPU Frequency driver, s3c244x cpu support

[    0.031326] bio: create slab <bio-0> at 0

[    0.044430] SCSI subsystem initialized

[    0.048355] libata version 3.00 loaded.

[    0.055343] s3c-i2c s3c2440-i2c.0: slave address 0x10

[    0.055422] s3c-i2c s3c2440-i2c.0: bus frequency set to 98 KHz

[    0.058492] s3c-i2c s3c2440-i2c.0: i2c-0: S3C I2C adapter

[    0.061261] pps_core: LinuxPPS API ver. 1 registered

[    0.061328] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>

[    0.062565] PTP clock support registered

[    0.003178] Advanced Linux Sound Architecture Driver Initialized.

[    0.008543] Switching to clocksource samsung_clocksource_timer

[    0.024857] NET: Registered protocol family 2

[    0.027753] TCP established hash table entries: 512 (order: 0, 4096 bytes)

[    0.027849] TCP bind hash table entries: 512 (order: -1, 2048 bytes)

[    0.027894] TCP: Hash tables configured (established 512 bind 512)

[    0.028342] TCP: reno registered

[    0.028443] UDP hash table entries: 256 (order: 0, 4096 bytes)

[    0.028513] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

[    0.029779] NET: Registered protocol family 1

[    0.041744] squashfs: version 4.0 (2009/01/31) Phillip Lougher

[    0.041832] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.

[    0.042710] yaffs: yaffs built Oct  9 2014 17:16:19 Installing.

[    0.042811] msgmni has been set to 117

[    0.050861] io scheduler noop registered

[    0.050937] io scheduler deadline registered (default)

[    0.051065] io scheduler cfq registered

[    0.061978] s3c2410-lcd s3c2410-lcd: fb0: s3c2410fb frame buffer device

[    0.000619] mini2440_backlight       initialized

[    0.001951] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled

[    0.007414] s3c2440-uart.0: ttySAC0 at MMIO 0x50000000 (irq = 74) is a S3C2440

[    0.107548] console [ttySAC0] enabled

[    0.112662] s3c2440-uart.1: ttySAC1 at MMIO 0x50004000 (irq = 77) is a S3C2440

[    0.119725] s3c2440-uart.2: ttySAC2 at MMIO 0x50008000 (irq = 80) is a S3C2440

[    0.128885] buttons  initialized

[    0.130225] adc      initialized

[    0.132162] pwm      initialized

[    0.072881] at24 0-0050: 1024 byte 24c08 EEPROM, writable, 16 bytes/write

[    0.084043] s3c24xx-nand s3c2440-nand: Tacls=1, 9ns Twrph0=3 29ns, Twrph1=2 19ns

[    0.085837] s3c24xx-nand s3c2440-nand: NAND soft ECC

[    0.090743] NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit), 256MiB, page size: 2048, OOB size: 64

[    0.103638] Creating 4 MTD partitions on "nand":

[    0.106999] 0x000000000000-0x000000060000 : "u-boot"

[    0.117553] 0x000000060000-0x000000080000 : "u-boot-env"

[    0.123261] 0x000000080000-0x000000580000 : "kernel"

[    0.130403] 0x000000580000-0x000010000000 : "rootfs"

[    0.084023] mtd: device 3 (rootfs) set to be root filesystem

[    0.084241] mtd: partition "rootfs_data" created automatically, ofs=0x7a0000, len=0xf860000

[    0.092312] 0x0000007a0000-0x000010000000 : "rootfs_data"

[    0.119985] dm9000 dm9000: read wrong id 0x01010101

[    0.120100] dm9000 dm9000: eth%d: Invalid ethernet MAC address. Please set using ifconfig

[    0.130612] eth0: dm9000e at 848ba300,848bc304 IRQ 55 MAC: 4e:5b:71:c8:3f:43 (random)

[    0.071277] dm9000 init!

[    0.074944] mousedev: PS/2 mouse device common for all mice

[    0.079742] s3c-rtc s3c2410-rtc: rtc disabled, re-enabling

[    0.085084] s3c-rtc s3c2410-rtc: rtc core: registered s3c as rtc0

[    0.090655] i2c /dev entries driver

[    0.095456] s3c2410-wdt s3c2410-wdt: tmr_margin value out of range, default 15 used

[    0.102949] s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq disabled

[    0.109192] cpufreq: Unable to obtain msysclk: -2

[    0.112683] cpuidle: using governor ladder

[    0.117570] TCP: cubic registered

[    0.119923] NET: Registered protocol family 17

[    0.124514] 8021q: 802.1Q VLAN Support v1.8

[    0.128645] VFP support v0.3: not present

[    0.073424] regulator-dummy: incomplete constraints, leaving on

[    0.076879] s3c-rtc s3c2410-rtc: setting system clock to 2000-01-01 13:41:01 UTC (946734061)

[    0.082220] ALSA device list:

[    0.084922]   No soundcards found.

[    0.089398] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", error -19

[    0.101859] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.

[    0.104281] Freeing unused kernel memory: 144K (803f7000 - 8041b000)

[    0.124523] usbcore: registered new interface driver usbfs

[    0.125736] usbcore: registered new interface driver hub

[    0.131000] usbcore: registered new device driver usb

[    0.073229] Button Hotplug driver version 0.4.1

[    0.086973] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver

[    0.091072] s3c2410-ohci s3c2410-ohci: S3C24XX OHCI

[    0.092421] s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1

[    0.100046] s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000

[    0.117496] hub 1-0:1.0: USB hub found

[    0.117665] hub 1-0:1.0: 2 ports detected

[    0.136006] usbcore: registered new interface driver usb-storage

[    0.216808] usb 1-1: new full-speed USB device number 2 using s3c2410-ohci

[    0.234661] usb-storage 1-1:1.0: USB Mass Storage device detected

[    0.171424] scsi0 : usb-storage 1-1:1.0

[    0.473236] scsi 0:0:0:0: Direct-Access     iT1167B  USB Flash Disk   0.00 PQ: 0 ANSI: 2

[    0.491122] sd 0:0:0:0: [sda] 7892992 512-byte logical blocks: (4.04 GB/3.76 GiB)

[    0.498038] sd 0:0:0:0: [sda] Write Protect is off

[    0.498150] sd 0:0:0:0: [sda] Mode Sense: 00 00 00 00

[    0.504055] sd 0:0:0:0: [sda] Asking for cache data failed

[    0.504168] sd 0:0:0:0: [sda] Assuming drive cache: write through

[    0.482300] sd 0:0:0:0: [sda] Asking for cache data failed

[    0.482410] sd 0:0:0:0: [sda] Assuming drive cache: write through

[    0.497700]  sda: sda4

[    0.527318] sd 0:0:0:0: [sda] Asking for cache data failed

[    0.527431] sd 0:0:0:0: [sda] Assuming drive cache: write through

[    0.468672] sd 0:0:0:0: [sda] Attached SCSI removable disk

[    2.512196] NET: Registered protocol family 10

[    2.495079] nf_conntrack version 0.5.0 (945 buckets, 3780 max)

[    2.511072] ip6_tables: (C) 2000-2006 Netfilter Core Team

[    2.538708] ip_tables: (C) 2000-2006 Netfilter Core Team

[    2.580735] xt_time: kernel timezone is -0000

[    2.601752] PPP generic driver version 2.4.2

[    2.609829] NET: Registered protocol family 24

[    5.407196] dm9000 dm9000 eth0: link down

[    5.408170] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready

[    5.382501] device eth0 entered promiscuous mode

[    5.384850] br-lan: port 1(eth0) entered forwarding state

[    5.386925] br-lan: port 1(eth0) entered forwarding state

[    5.714880] br-lan: port 1(eth0) entered disabled state

[    5.963435] dm9000 dm9000 eth0: link up, 100Mbps, full-duplex, lpa 0xCDE1

[    5.993481] br-lan: port 1(eth0) entered forwarding state

[    5.993740] br-lan: port 1(eth0) entered forwarding state

[    5.999116] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

[    6.574294] br-lan: port 1(eth0) entered forwarding state

[    7.408599] jffs2: notice: (848) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (0 unchecked, 1 orphan) and 16 of xref (0 dead, 9 orphan) found.