FWSM路由模式的三个配置实例
FWSM路由模式的三个配置实例
OUTSIDE――MSFC―vlan10―
FWSM―vlan20―CORE――HOST
的配置过程
・ Create the Layer 3 Interface to be used as gateway by
FWSM. This is done in global config mode.
o MSFC(config)#interface vlan 10
o MSFC(config-int)#ip address 206.10.10.1 255.255.255.0
o MSFC(config-int)#no shutdown
・ Define a vlan-group for the Firewall Module and assign the vlans to a Firewall Module.
o MSFC(config)#firewall vlan-group 1 10,20
o MSFC(config)#firewall module 3 vlan-group 1
・ Session to the
FWSM. To do this type “session slot &module # proc 1” in enable mode. For our example we will assume the
FWSM is in slot 3 of the chassis.
o MSFC#session slot 3 proc 1
・ Create Layer 3 interfaces on the
FWSM. The command to do this is “nameif &vlan# &interface name &security level” in
global config mode.
o
FWSM(config)#nameif 10 outside 0
o
FWSM(config)#ip address outside 206.10.10.2 255.255.255.0
o
FWSM(config)#nameif 20 inside 100
o
FWSM(config)#ip address inside 10.20.20.1 255.255.255.0
・ Add default route to Outside security level on the
FWSM.
o
FWSM(config)#route outside 0.0.0.0 0.0.0.0 206.10.10.1 1
・ Configure a STATIC NAT entry for hosts A and B to be seen by outside users.
o
FWSM(config)#static (inside,outside) 206.10.10.25 10.20.20.25 netmask 255.255.255.255 ?Host A
o
FWSM(config)#static (inside,outside) 206.10.10.26 10.20.20.26 netmask 255.255.255.255 ?Host B
・ Configure a NAT entry for users in the inside security level that wish to initiate a connection to the outside security level.
o
FWSM(config)#nat (inside) 1 0 0
o
FWSM(config)#global (outside) 1 206.10.10.100
・ Configure access control lists and apply them to the interfaces to restrict access to the inside securty level by hosts on the
outside security level.
o
FWSM(config)#access-list outside-acl permit tcp any host 206.10.10.25 eq www
o
FWSM(config)# access-list outside-acl permit tcp any host 206.10.10.25 eq ftp
o
FWSM(config)# access-list outside-acl permit tcp any host 206.10.10.25 eq ftp-data
o
FWSM(config)# access-list outside-acl permit icmp any host 206.10.10.25 (this allows outside users to ping)
o
FWSM(config)#access-list outside-acl permit tcp any host 206.10.10.26 eq www
o
FWSM(config)# access-list outside-acl permit tcp any host 206.10.10.26 eq ftp
o
FWSM(config)# access-list outside-acl permit tcp any host 206.10.10.26 eq ftp-data
o
FWSM(config)# access-list outside-acl permit icmp any host 206.10.10.26 ?(this allows outside users to ping)
・ Now apply the defined access-list "outside-acl" to the outside interface as follows:
o
FWSM(config)#access-group outside-acl in interface outside
2
OUTSIDE―vlan10―
FWSM―vlan20―MSFC―vlan30―CORE――HOST
与上面例子的不同之处在于：
FWSM
通过vlan10
连接外部，所以65
连接外部的g8/1
要属于vlan10
o MSFC(config)#interface gigabit 8/1
o MSFC(config-int)# switchport
o MSFC(config-int)#switchport mode access
o MSFC(config-int)#switchport access vlan 10
o MSFC(config-int)#no shutdown
MSFC上使用静态路由即可
o MSFC(config)#ip route 0.0.0.0 0.0.0.0 10.20.20.1
FWSM使用静态路由以便使外部数据可以进入内部
o
FWSM(config)#route inside 10.0.0.0 255.0.0.0 10.20.20.2
3
DMZ
|
vlan50
|
OUTSIDE――MSFC―vlan10―
FWSM―vlan20―CORE――HOST
的配置过程比1
增加了如下：
|
vlan60
|
DMZ
・ Create the DMZ VLAN’s on the MSFC in global config mode
o MSFC(config)#vlan 50
o MSFC(config-vlan)#no shutdown
o MSFC(config)#vlan 60
o MSFC(config-vlan)#no shutdown
・ Add VLAN’s 50 and 60 to the firewall-vlan group created in Configuration #1.
o MSFC(config)#firewall vlan-group 1 50,60
DMZ
的计算机连接端口要设成switchport
以便
FWSM
可以看到
o MSFC(config)#interface FastEthernet 7/1
o MSFC(config-int)#switchport
o MSFC(config-int)switchport mode access
o MSFC(config-int)switchport access vlan 60
o MSFC(config-int)no shutdown
・ Session to the
FWSM as outlined in Configuration #1 and configure the Layer 3 interfaces for the DMZ security levels.
o
FWSM(config)#nameif 60 dmz1 60
o
FWSM(config)#nameif 50 dmz2 50
o
FWSM(config)#ip address dmz1 10.60.60.1 255.255.255.0
o
FWSM(config)#ip address dmz2 10.50.50.1 255.255.255.0
・ To enable users to be able to connect with the servers in the DMZ’s, STATIC and NAT translations will have to be
established depending upon the direction of the traffic flow.
o
FWSM(config)#nat (dmz1) 2 10.60.60.0 255.255.255.0
o
FWSM(config)#global (outside) 2 206.10.10.60
o
FWSM(config)#global (dmz2) 2 10.50.50.200
o
FWSM(config)#nat (dmz2) 3 10.50.50.0 255.255.255.0
o
FWSM(config)#global (outside) 3 206.10.10.50
o
FWSM(config)#static (inside,dmz1) 10.60.60.60 10.20.20.25 netmask 255.255.255.255
o
FWSM(config)#static (inside,dmz2) 10.50.50.50 10.20.20.25 netmask 255.255.255.255
o
FWSM(config)#static (dmz1,dmz2) 10.50.50.50 10.60.60.25 netmask 255.255.255.255
有关acl
o
FWSM(config)#access-list web permit tcp any host 206.10.10.125 eq www
o
FWSM(config)#access-list web permit tcp any host 206.10.1