CISCO 4006S 配置实例

DQ-4006S> (enable) show config
This command shows non-default configurations only.
Use 'show config all' to show both default and non-default configurations.
.......
................
................
................
..................


..

begin
!
# ***** NON-DEFAULT CONFIGURATION *****
!
!
#time: Wed Jun 27 2007, 20:51:47
!
#version 5.5(1)
!
!
#system web interface version(s)
set password $2$HtUv$/QWmbS1bU5cejCIZ3JMyB/
set enablepass $2$gxSC$VWv7UMSylUlecRNXViAS/0
!
#system
set system name  DQ-4006S
!
#frame distribution method
set port channel all distribution mac both
!
#vtp
set vtp domain home
set vtp pruning enable
set vlan 1 name default type ethernet mtu 1500 said 100001 state active
set vlan 2 name hpublic type ethernet mtu 1500 said 100002 state active
set vlan 3 name hshhl type ethernet mtu 1500 said 100003 state active
set vlan 4 name hdqhl type ethernet mtu 1500 said 100004 state active
set vlan 5 name hxqhl type ethernet mtu 1500 said 100005 state active
set vlan 6 name hdhhl type ethernet mtu 1500 said 100006 state active
set vlan 7 name hshcw type ethernet mtu 1500 said 100007 state active
set vlan 8 name hsh28 type ethernet mtu 1500 said 100008 state active
set vlan 9 name hsh07 type ethernet mtu 1500 said 100009 state active
set vlan 10 name hlydq type ethernet mtu 1500 said 100010 state active
set vlan 11 name hlyxq type ethernet mtu 1500 said 100011 state active
set vlan 12 name hdhsz type ethernet mtu 1500 said 100012 state active
set vlan 13 name home type ethernet mtu 1500 said 100013 state active
set vlan 14 name caiwugongsi type ethernet mtu 1500 said 100014 state active
set vlan 15 name new1 type ethernet mtu 1500 said 100015 state active
set vlan 16 name 16 type ethernet mtu 1500 said 100016 state active
set vlan 40 name 40 type ethernet mtu 1500 said 100040 state active
set vlan 100 name VLAN0100 type ethernet mtu 1500 said 100100 state active
set vlan 1002 name fddi-default type fddi mtu 1500 said 101002 state active
set vlan 1004 name fddinet-default type fddinet mtu 1500 said 101004 state act
e stp ieee
set vlan 1005 name trnet-default type trbrf mtu 1500 said 101005 state active
p ibm
set vlan 1003 name token-ring-default type trcrf mtu 1500 said 101003 state ac
ve mode srb aremaxhop 0 stemaxhop 0 backupcrf off
!
#ip
set interface sc0 1 10.224.31.91/255.255.255.0 10.224.31.255

set interface sl0 down
set interface me1 down
set ip route 0.0.0.0/0.0.0.0         10.224.31.254
!
#syslog
set logging level cops 2 default
!
#set boot command
set boot config-register 0x2
set boot system flash bootflash:cat4000.5-5-1.bin
!
#permit list
set ip permit enable telnet
set ip permit 10.224.31.0 255.255.255.0
!
#port channel
set port channel 1/1-2 1
set port channel 3/1-2 2
set port channel 3/3-6 3
set port channel 2/1-2 4
set port channel 2/3-6 5
set port channel 4/3-4 48
set port channel 4/5-8 49
set port channel 4/9-12 50
set port channel 4/13-16 51
set port channel 4/17-20 52
set port channel 4/21-24 53
set port channel 4/25-28 54
set port channel 4/29-32 55
set port channel 4/33-34 56
set port channel 4/1-2 100
!
#errdisable timeout
set errdisable-timeout enable other
set errdisable-timeout enable udld
set errdisable-timeout enable duplex-mismatch
set errdisable-timeout enable bpdu-guard
set errdisable-timeout enable channel-misconfig
!
#module 1 : 2-port 1000BaseX Supervisor
set trunk 1/1  on dot1q 1-1005
set trunk 1/2  on dot1q 1-1005
set port channel 1/1-2 mode on
!
#module 2 : 6-port 1000BaseX Ethernet
set udld enable 2/6
set trunk 2/1  on dot1q 1-1005
set trunk 2/2  on dot1q 1-1005
set trunk 2/3  on dot1q 1-1005
set trunk 2/4  on dot1q 1-1005
set trunk 2/5  on dot1q 1-1005
set trunk 2/6  on dot1q 1-1005
!
#module 3 : 6-port 1000BaseX Ethernet
set udld enable 3/5-6
set trunk 3/1  on dot1q 1-1005
set trunk 3/2  on dot1q 1-1005
set trunk 3/3  on dot1q 1-1005
set trunk 3/4  on dot1q 1-1005
set trunk 3/5  on dot1q 1-1005
set trunk 3/6  on dot1q 1-1005
!
#module 4 : 34-port Router Switch Card
set vlan 8    4/3
set vlan 10   4/19,4/33-34
set port speed      4/34  100
set port duplex     4/34  full
set trunk 4/1  on dot1q 1-1005
set trunk 4/2  on dot1q 1-1005
set port channel 4/1-2 mode on
!
#module 5 empty
!
#module 6 empty
end

本文出自 “陈高儒的博客” 博客，谢绝转载！