BSCI―7：OSPF的路由汇总
BSCI―7：OSPF的路由汇总
2010-01-26 09:32:50
标签：
OSPF BSCI [ 推送到技术圈]
|
版权声明：原创作品，允许转载，转载时请务必以超链接形式标明文章 原始出处 、作者信息和本声明。否则将追究法律责任。 http://justim.blog.51cto.com/740099/270551
|
|
一、OSPF路由汇总优点：
OSPF路由汇总可以减少路由表条目,减少类型3和类型5的LSA的洪泛,节约带宽资源和减轻路由器CPU负载,还能够对拓扑的变化本地化
。
二、
OSPF路由汇总的两种类型如下:
（两种方式均会演示）
1.inter-area(IA) route summarization:发生在ABR上 2.external route summarization:发生在ASBR上
三、
实验1：OSPF区域间汇总，发生在ABR上，接口信息及IP地址规划，区域信息如拓扑所示。
步骤一：配置3台路由器，并且用OSPF。
R1：
R1>
R1>en
R1#conf t
R1(config)#interface f0/0
R1(config-if)#ip address 192.168.1.1 255.255.255.0
R1(config-if)#no sh
R1(config-if)#exit
R1(config)#interface loopback 0
R1(config-if)#ip address 10.1.1.1 255.255.255.0
R1(config-if)#int lo1
R1(config-if)#ip address 10.1.2.1 255.255.255.0
R1(config-if)#int lo2
R1(config-if)#ip address 10.1.3.1 255.255.255.0
R1(config-if)#exit
R1(config)#router ospf 1 //启用OSPF路由协议
R1(config-router)#network 10.1.1.1 0.0.0.0 area 1 //发布网段
R1(config-router)#network 10.1.2.1 0.0.0.0 area 1
R1(config-router)#network 10.1.3.1 0.0.0.0 area 1
R1(config-router)#network 192.168.1.1 0.0.0.0 area 1
R1(config-router)#end
R1#
R2：
R2>en
R2#conf t
R2(config)#interface f0/0
R2(config-if)#ip address 192.168.1.2 255.255.255.0
R2(config-if)#no sh
R2(config-router)#exit
R2(config)#interface f0/1
R2(config-if)#ip address 192.168.2.2 255.255.255.0
R2(config-if)#no sh
R2(config-if)#exit
R2(config)#router ospf 1 //启用OSPF路由协议
R2(config-router)#network 192.168.1.2 0.0.0.0 area 1 //同上
R2(config-router)#network 192.168.2.2 0.0.0.0 area 0
R2(config-router)#end
R2#
R3：
R3>
R3>en
R3#conf t
R3(config)#interface f0/1
R3(config-if)#ip add
R3(config-if)#ip address 192.168.2.1 255.255.255.0
R3(config-if)#no sh
R3(config-if)#exit
R3(config-router)#network 192.168.2.1 0.0.0.0 area 0
R3(config-router)#end
R3#
查看R3路由表： //已经学习到R1三条明细路由
R3#sh ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
10.0.0.0/32 is subnetted, 3 subnets
O IA 10.1.1.1 [110/3] via 192.168.2.2, 00:01:18, FastEthernet0/1
O IA 10.1.2.1 [110/3] via 192.168.2.2, 00:01:18, FastEthernet0/1
O IA 10.1.3.1 [110/3] via 192.168.2.2, 00:01:18, FastEthernet0/1
O IA 192.168.1.0/24 [110/2] via 192.168.2.2, 00:01:18, FastEthernet0/1
C 192.168.2.0/24 is directly connected, FastEthernet0/1
R3#
步骤二：在R2（ABR）上执行汇总，再次查看R3上路由表
R2(config)#router ospf 1
R2(config-router)#area 1 range 10.1.0.0 255.255.252.0
//把3条明细路由汇总为掩码为/22的汇总路由.
R2(config-router)#end
R2#
查看R3路由表：
R3#sh ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
10.0.0.0/22 is subnetted, 1 subnets
O IA 10.1.0.0 [110/65] via 192.168.2.2, 00:00:16, FastEthernet0/1
//变为掩码为22的汇总路由
C 192.168.2.0/24 is directly connected, FastEthernet0/1
R3#
实验2：OSPF域间汇总，发生在（ASBR）上,拓扑如下,R1运行了OSPF与RIP两种路由协议，所以它为ASBR，IP地址与区域已规划好.
步骤一：在2台路由器上配置OSPF与RIP，并发布网段.
R1：
Router>
Router>en
Router#conf t
Router(config)#hostname R1
R1(config)#interface f0/0
R1(config-if)#ip address 192.168.1.1 255.255.255.0
R1(config-if)#no sh
R1(config)#interface loopback 0
R1(config-if)#ip address 10.1.1.1 255.255.255.0
R1(config-if)#int lo1
R1(config-if)#ip address 10.1.2.1 255.255.255.0
R1(config-if)#int lo2
R1(config-if)#ip address 10.1.3.1 255.255.255.0
R1(config-if)#exit
R1(config)#router ospf 1 //启用OSPF路由协议
R1(config-router)#network 192.168.1.1 0.0.0.0 area 0
R1(config-router)#exit
R1(config)#router rip //启用RIP路由协议
R1(config-router)#version 2 //指定版本2
R1(config-router)#no auto-summary //不要自动汇总
R1(config-router)#network 10.1.1.0 //发布网段
R1(config-router)#network 10.1.2.0
R1(config-router)#network 10.1.3.0
R1(config-router)#exit
R1(config)#end
R1#
R2: Router>
Router>en
Router#conf t
Router(config)#hostname R2
R2(config)#interface f0/0
R2(config-if)#ip address 192.168.1.2 255.255.255.0
R2(config-if)#no sh
R2(config-if)#exit
R2(config)#router ospf 1 //同上
R2(config-router)#network 192.168.1.2 0.0.0.0 area 0
R2(config-router)#end
R2#
步骤二：在R1上把RIP与OSPF互相重发布,并查看R2路由表.
R1(config)#router rip
R1(config-router)#redistribute ospf 1 metric 1 //把OSPF发布进RIP，度量值为1
R1(config-router)#exit
R1(config)#router ospf 1
R1(config-router)#redistribute rip subnets //把RIP路由发布进OSPF
R1(config-router)#end
R1#
查看R2路由表： //此时已经学习重发布进OSPF的外部路由表条目
R2#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route
Gateway of last resort is not set 10.0.0.0/24 is subnetted, 3 subnets
O E2 10.1.3.0 [110/20] via 192.168.1.1, 00:00:40, FastEthernet0/0
O E2 10.1.2.0 [110/20] via 192.168.1.1, 00:00:40, FastEthernet0/0
O E2 10.1.1.0 [110/20] via 192.168.1.1, 00:00:40, FastEthernet0/0
C 192.168.1.0/24 is directly connected, FastEthernet0/0
R2#
注：E2表示OSPF的外部路由类型2.
步骤三：在R1（ASBR）上做域间汇总，使得3条明细汇总为一条.并查看R2路由表.
R1(config)#router ospf 1
R1(config-router)#summary-address 10.1.0.0 255.255.252.0
//把之前3条明细路由汇总成掩码为22的汇总路由
R1(config-router)#end
R1#
查看R2路由表：
R2#show ip route //此时已经变为掩码为22的汇总路由.
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route
Gateway of last resort is not set 10.0.0.0/22 is subnetted, 1 subnets
O E2 10.1.0.0 [110/20] via 192.168.1.1, 00:00:44, FastEthernet0/0
C 192.168.1.0/24 is directly connected, FastEthernet0/0
R2#
实验完成.
本文出自 “ 梅岩〃s博客” 博客，请务必保留此出处 http://justim.blog.51cto.com/740099/270551
本文出自 51CTO.COM技术博客
|