proxmox ve 2.2 elastix2.3模板制作
安装好proxmox ve 2.2ssh 到 proxmox ve
apt-get -y update
apt-get -y makedev
apt-get -y install build-essential make pve-headers-`uname -r`
cd /usr/src/
wget http://downloads.digium.com/pub/telephony/dahdi-linux-complete/dahdi-linux-complete-current.tar.gz
tar zxfv dahdi-linux-complete-current.tar.gz
cd dahdi-linux-complete-*
make all
make install
make config
mkdir /etc/asterisk
service dahdi start
dahdi_genconf
vi /etc/dahdi/modules 全部加#号注释
sed -i 's|ipt_REJECT ipt_tos ipt_limit ipt_multiport iptable_filter iptable_mangle ipt_TCPMSS ipt_tcpmss ipt_ttl ipt_length|ipt_REJECT ipt_tos ipt_TOS ipt_LOG ip_conntrack ipt_limit ipt_multiport iptable_filter iptable_mangle ipt_TCPMSS ipt_tcpmss ipt_ttl ipt_length ipt_state iptable_nat ip_nat_ftp|' /etc/vz/vz.conf
/etc/init.d/vz restart
//禁用ipv6
/boot/grub/grub.cfg 中 linux /vmlinuz-2.6.32-16-pve root=/dev/mapper/pve-root ro quiet 替换成 linux /vmlinuz-2.6.32-16-pve root=/dev/mapper/pve-root ro ipv6.disable=1 quiet
在elastix2.3机器上 参考 http://wiki.openvz.org/Creating_a_CentOS_5.0_Template
First, create a file called /tmp/exclude and add the following lines to it:
.bash_history
lost+found
/dev/*
/mnt/*
/tmp/*
/proc/*
/sys/*
/usr/src/*
tar --numeric-owner -czvf /tmp/centos-5.7-x86_64-elasitx_orig-image.tar.gz -X /tmp/exclude /
- where <ARCH> represents the system architecture (i386 or
- x86_64) and <DISTRO> represents the distribution (default, minimal, etc.).
scp /tmp/centos-5.7-x86_64-elasitx_orig-image.tar.gz root@ip:/var/lib/vz/template/iso
回到proxmox ve 机器 使用 web以centos-5.7-x86_64-elasitx_orig-image 为模板创建vt虚拟机 假设 vm id 为 100
ssh 到 proxmox ve
cd /var/lib/vz/private/100
Edit the etc/inittab file and comment out the lines that respawn /sbin/mingetty on tty1 through tty6. Just put a # at the beginning of the line.
在 etc/inittab 文件最后面加入
1:2345:respawn:/sbin/agetty tty1 38400 linux
Remove the etc/mtab file and then create a symbolic link by typing ln -s /proc/mounts etc/mtab
Remove all of the lines from etc/fstab except for the line that mounts /dev/pts
Edit etc/rc.d/rc.sysinit and comment out the line that starts /sbin/start_udev by placing a # at the beginning of the line.
mknod dev/ptmx c 5 2
mkdir dev/pts
cd dev
/sbin/MAKEDEV ttyp ptyp
cd ../
mknod dev/null c 1 3
mknod -m 644 dev/random c 1 8
mknod dev/urandom c 1 9
mknod dev/tty9 c 4 9
Create the var/lock/rpm folder.
Edit etc/sysconfig/network and set NETWORKING_IPV6 to no.
Add the following lines to etc/modprobe.d/blacklist.conf:
blacklist ipv6
blacklist net-pf-10
Disable any physical NICs by modifying the etc/sysconfig/network-scripts/ifcfg-ethX files (where X is the interface number starting from 0) and setting ONBOOT to no.
Check etc/sysconfig/init to see if PROMPT=yes, and then change to no. Otherwise when startup init script rc will enter interactive mode and wait there forever
vzctl set 100 --devnodes dahdi/pseudo:rw --save
vzctl start 100
vzctl enter 100
chkconfig haldaemon off
chkconfig dahdi off
chkconfig wanrouter off
rm -rf /etc/init.d/dahdi
rm -rf /etc/init.d/wanrouter
chkconfig acpid off
chkconfig kudzu off
chkconfig xfs off
chkconfig rpcidmapd off
chkconfig rpcgssd off
chkconfig nfslock off
chkconfig mdmonitor off
chkconfig ip6tables off
exit
cd /var/lib/vz/private/100
tar -czvf /var/lib/vz/template/cache/centos-5-x86_64-elasitx.tar.gz ./