Allegro DRC错误代码
Allegro DRC错误代码
| 代码 |
相关对象 |
说明 |
| 单一字符代码 |
||
| L |
Line |
走线 |
| P |
Pin |
元件脚 |
| V |
Via |
贯穿孔 |
| K |
Keep in/out |
允许区域/禁止区域 |
| C |
Component |
元件层级 |
| E |
Electrical Constraint |
电气约束 |
| J |
T-Junction |
呈现T形的走线 |
| I |
Island Form |
被Pin或Via围成的负片孤铜 |
|
|
|
|
| 错误代码前置码说明 |
|
|
| W |
Wire |
与走线相关的错误 |
| D |
Design |
与整个电路板相关的错误 |
| M |
Soldemask |
与防焊层相关的错误 |
|
|
|
|
| 错误代码后置码说明 |
|
|
| S |
Shape/Stub |
与走线层的Shape或分支相关的错误 |
| N |
Not Allowed |
与不允许的设置相关的错误 |
| W |
Width |
与宽度相关的错误 |
|
|
|
|
| 双字符错误代码 |
|
|
| BB |
Bondpad to Bondpad |
Bondpad之间的错误 |
| BL |
Bondpad to Line |
Bondpad与Line之间的错误 |
| BS |
Bondpad to Shape |
Bondpad与Shape 之间的错误 |
| CC |
Package to Package |
Package之间的 Spacing 错误 |
| Symbol Soldermask to Symbol |
Soldermask零件防焊层之间的Spacing 错误 |
|
| DF |
Differential Pair Length Tolerance |
差分对走线的长度误差过长 |
| Differential Pair Primary Max Separation |
差分对走线的主要距离太大 |
|
| Differential Pair Secondary Max Separation |
差分对走线的次要距离太大 |
|
| Differential Pair Secondary Max Length |
差分对走线的次要距离长度过长 |
|
| DI |
Design Constraint Negative Plane Island |
负片孤铜的错误 |
| ED |
Propagation-Delay |
走线的长度错误 |
| Relative-Propagation-Delay |
走线的等长错误 |
|
| EL |
Max Exposed Length |
走线在外层（TOP&BOTTOM）的长度过长 |
| EP |
Max Net Parallelism Length-Distance Pair |
已超过Net之间的平行长度 |
| ES |
Max Stub Length |
走线的分支过长 |
| ET |
Electrical Topology |
走线连接方式的错误 |
| EV |
Max Via Count |
已超过走线使用的VIA的最大数目 |
| EX |
Max Crosstalk |
已超过Crosstalk值 |
| Max Peak Crosstalk |
已超过Peak Crosstalk值 |
|
| HH |
Hold to Hold Spacing |
钻孔之间的距离太近 |
| HW |
Diagonal Wire to Hold Spacing |
斜线与钻孔之间的距离太近 |
| Hold to Orthogonal Wire Spacing |
钻孔与垂直/水平线之间的距离太近 |
|
| IM |
Impedance Constraint |
走线的阻抗值错误 |
| JN |
T Junction Not Allowed |
走线呈T形的错误 |
| KB |
Route Keepin to Bondpad |
Bondpad在Keepin之外 |
| Route keepout to Bondpad |
Bondpad在keepout之内 |
|
| Via Keepout to Bondpad |
Bondpad在Via Keepout之内 |
|
| KC |
Package to Place Keepin Spacing |
元件在Place Keepin之外 |
| Package to Place Keepout Spacing |
元件在Place Keepout之内 |
|
| KL |
Line to Route Keepin Spacing |
走线在Route Keepin之外 |
| Line to Route Keepout Spacing |
走线在Route Keepout之内 |
|
| KS |
Shape to Route Keepin Spacing |
Shape在Route Keepin之外 |
| Shape to Route Keepout Spacing |
Shape在Route Keepout之内 |
|
| KV |
BBVia to Route Keepin Spacing |
BBVia在Route Keepin之外 |
| BBVia to Route Keepout Spacing |
BBVia在Route Keepout之内 |
|
| BBVia to Via Keepout Spacing |
BBVia在Via Keepout之内 |
|
| Test Via to Route Keepin Spacing |
Test Via在Route Keepin之外 |
|
| Test Via to Route Keepout Spacing |
Test Via在Route Keepout之内 |
|
| Test Via to Via Keepout Spacing |
Test Via在Via Keepout之内 |
|
| Through Via to Route Keepin Spacing |
Through Via在Route Keepin之外 |
|
| Through Via to Route Keepout Spacing |
Through Via在Route Keepout之内 |
|
| Through Via to Via Keepout Spacing |
Through Via在Via Keepout之内 |
|
| LB |
Min Self Crossing Loopback Length |
无 |
| LL |
Line to Line Spacing |
走线之间太近 |
| LS |
Line to Shape Spacing |
走线与Shape 太近 |
| LW |
Min Line Width |
走线的宽度太细 |
| Min Neck Width |
走线变细的宽度太细 |
|
| MA |
Soldermask Alignment Error Pad |
Soldermask Tolerance太小 |
| MC |
Pin/Via Soldermask to Symbol Soldermask |
Pad与Symbol Soldermask之间的错误 |
| MM |
Pin/Via Soldermask to Pin/Via Soldermask |
Pad Soldermask之间的错误 |
| PB |
Pin to Bondpad |
Pin与Bondpad之间的错误 |
| PL |
Line to SMD Pin Spacing |
走线与SMD元件脚太近 |
| Line to Test Pin Spacing |
走线与Test元件脚太近 |
|
| Line to Through Pin Spacing |
走线与Through元件脚太近 |
|
| PP |
SMD Pin to SMD Pin Spacing |
SMD元件脚与SMD元件脚太近 |
| SMD Pin to Test Pin Spacing |
SMD元件脚与Test元件脚太近 |
|
| Test Pin to Test Pin Spacing |
Test元件脚与Test元件脚太近 |
|
| Test Pin to Through Pin Spacing |
Test元件脚与Through元件脚太近 |
|
| Through Pin to SMD Pin Spacing |
Through元件脚与SMD元件脚太近 |
|
| Through Pin to Through Pin Spacing |
Through元件脚与Through元件脚太近 |
|
| PS |
Shape to SMD Pin Spacing |
Shape与SMD元件脚太近 |
| Shape to Test Pin Spacing |
Shape与Test元件脚太近 |
|
| Through Pin to Shape Spacing |
Through元件脚与Shape太近 |
|
| PV |
BBVia to SMD Pin Spacing |
BBVia与SMD元件脚太近 |
| BBVia to Test Pin Spacing |
BBVia与Test元件脚太近 |
|
| BBVia to Through Pin Spacing |
BBVia 与Through元件脚太近 |
|
| SMD Pin to Test Via Spacing |
SMD Pin与Test Via太近 |
|
| SMD Pin to Through Via Spacing |
SMD Pin与Through Via太近 |
|
| Test Pin to Test Via Spacing |
Test Pin与Test Via太近 |
|
| Test Pin to Through Via Spacing |
Test Pin与Through Via太近 |
|
| Test Via to Through Pin Spacing |
Test Via与Through Pin太近 |
|
| Through Pin to Through Via Spacing |
Through Pin与Through Via太近 |
|
| RC |
Package to Hard Room |
元件在其他的Room之内 |
| RE |
Min Length Route End Segment at 135Degree |
无 |
| Min Length Route End Segment at 45/90Degree |
无 |
|
| SB |
135Degree Turn to Adjacent Crossing Distance |
无 |
| 90Degree Turn to Adjacent Crossing Distance |
无 |
|
| SL |
Min Length Wire Segment |
无 |
| Min Length Single Segment Wire |
无 |
|
| SN |
Allow on Etch Subclass |
允许在走线层上 |
| SO |
Segment Orientaion |
无 |
| BB |
Bondpad to Bondpad |
Bondpad之间的错误 |
| SS |
Shape to Shape |
Shape之间的错误 |
| TA |
Max Turn Angle |
无 |
| VB |
Via to Bondpad |
Via 与Bondpad之间的错误 |
| VG |
Max BB Via Stagger Distance |
同一段线的BB Via之间的距离太长 |
| Min BB Via Gap |
BB Via之间太近 |
|
| Min BB Via Stagger Distance |
同一段线的BB Via之间的距离太近 |
|
| Pad/Pad Direct Connect |
Pad 在另一个Pad 之上 |
|
| VL |
BB Via to Line Spacing |
BB Via与走线太近 |
| Line to Through Via Spacing |
走线与Through Via太近 |
|
| Line to Test Via Spacing |
走线与Test Via太近 |
|
| VS |
BB Via to Shape Spacing |
BB Via与Shape太近 |
| Shape to Test Via Spacing |
Shape 与Test Via太近 |
|
| Shape to Through Via Spacing |
Shape与Through Via太近 |
|
| VV |
BB Via to BB Via Spacing |
BB Via之间太近 |
| BB Via to Test Via Spacing |
BB Via与Test Via太近 |
|
| BB Via to Through Via Spacing |
BB Via与Through Via太近 |
|
| Test Via to Test Via Spacing |
Test Via之间太近 |
|
| Test Via to Through Via Spacing |
Test Via与Through Via太近 |
|
| Through Via to Through Via Spacing |
Through Via之间太近 |
|
| WA |
Min Bonding Wire Length |
Bonding Wire 长度太短 |
| WE |
Min End Segment Length |
无 |
| Min Length Wire End Segment at 135Degree |
无 |
|
| Min Length Wire End Segment at 45/90Degree |
无 |
|
| WI |
Max Bonding Wire Length |
Bonding Wire 长度太长 |
| WW |
Diagonal Wire to Diagonal Wire Spacing |
斜线之间太近 |
| Diagonal Wire to Orthogonal Wire Spacing |
斜线与垂直/水平线之间的距离太近 |
|
| Orthogonal Wire to Orthogonal Wire Spacing |
垂直/水平线之间的距离太近 |
|
| WX |
Max Number of Crossing |
无 |
| Min Distance between Crossing |
无 |
|
| XB |
135 Degree Turn to Adjacent Crossing Distance |
无 |
| 90 Degree Turn to Adjacent Crossing Distance |
无 |
|
| XD |
Externally Determined Violation |
无 |
| XS |
Crossing to Adjacent Segment Distances |
无 |
|
|
|
|