802.1q相关mib
Q-BRIDGE-MIB DEFINITIONS ::= BEGIN
-- -------------------------------------------------------------
-- MIB for IEEE 802.1Q Devices
-- -------------------------------------------------------------
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE,
Counter32, Counter64, Unsigned32, TimeTicks, Integer32
FROM SNMPv2-SMI
RowStatus, TruthValue, TEXTUAL-CONVENTION, MacAddress
FROM SNMPv2-TC
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF
dot1dBridge, dot1dBasePortEntry, dot1dBasePort
FROM BRIDGE-MIB
EnabledStatus
FROM P-BRIDGE-MIB
TimeFilter
FROM RMON2-MIB;
qBridgeMIB MODULE-IDENTITY
LAST-UPDATED "200601090000Z"
ORGANIZATION "IETF Bridge MIB Working Group"
CONTACT-INFO
"Email: [email protected]
[email protected]
David Levi
Postal: Nortel Networks
4655 Great America Parkway
Santa Clara, CA 95054
USA
Phone: +1 865 686 0432
Email: [email protected]
David Harrington
Postal: Effective Software
50 Harding Rd.
Portsmouth, NH 03801
USA
Phone: +1 603 436 8634
Email: [email protected]
Les Bell
Postal: Hemel Hempstead, Herts. HP2 7YU
UK
Email: [email protected]
Andrew Smith
Postal: Beijing Harbour Networks
Jiuling Building
21 North Xisanhuan Ave.
Beijing, 100089
PRC
Fax: +1 415 345 1827
Email: [email protected]
Paul Langille
Postal: Newbridge Networks
5 Corporate Drive
Andover, MA 01810
USA
Phone: +1 978 691 4665
Email: [email protected]
Anil Rijhsinghani
Postal: Accton Technology Corporation
5 Mount Royal Ave
Marlboro, MA 01752
USA
Phone:
Email: [email protected]
Keith McCloghrie
Postal: Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
Phone: +1 408 526 5260
Email: [email protected]"
DESCRIPTION
"The VLAN Bridge MIB module for managing Virtual Bridged
Local Area Networks, as defined by IEEE 802.1Q-2003,
including Restricted Vlan Registration defined by
IEEE 802.1u-2001 and Vlan Classification defined by
IEEE 802.1v-2001.
Copyright (C) The Internet Society (2006). This version of
this MIB module is part of RFC 4363; See the RFC itself for
full legal notices."
REVISION "200601090000Z"
DESCRIPTION
"Added Vlan TEXTUAL-CONVENTIONs,
dot1qPortRestrictedVlanRegistration, dot1vProtocol subtree,
qBridgeClassificationDeviceGroup, qBridgePortGroup2,
qBridgeClassificationPortGroup, and qBridgeCompliance2.
Clarified dot1qForwardAllStaticPorts,
qPortAcceptableFrameTypes, and qBridgeCompliance.
Deprecated qBridgePortGroup and qBridgeCompliance."
REVISION "199908250000Z"
DESCRIPTION
"The VLAN Bridge MIB module for managing Virtual Bridged
Local Area Networks, as defined by IEEE 802.1Q-1998.
Initial version, published as RFC 2674."
::= { dot1dBridge 7 }
qBridgeMIBObjects OBJECT IDENTIFIER ::= { qBridgeMIB 1 }
-- -------------------------------------------------------------
-- Textual Conventions
-- -------------------------------------------------------------
PortList ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Each octet within this value specifies a set of eight
ports, with the first octet specifying ports 1 through
8, the second octet specifying ports 9 through 16, etc.
Within each octet, the most significant bit represents
the lowest numbered port, and the least significant bit
represents the highest numbered port. Thus, each port
of the bridge is represented by a single bit within the
value of this object. If that bit has a value of '1',
then that port is included in the set of ports; the port
is not included if its bit has a value of '0'."
SYNTAX OCTET STRING
VlanIndex ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"A value used to index per-VLAN tables: values of 0 and
4095 are not permitted. If the value is between 1 and
4094 inclusive, it represents an IEEE 802.1Q VLAN-ID with
global scope within a given bridged domain (see VlanId
textual convention). If the value is greater than 4095,
then it represents a VLAN with scope local to the
particular agent, i.e., one without a global VLAN-ID
assigned to it. Such VLANs are outside the scope of
IEEE 802.1Q, but it is convenient to be able to manage them
in the same way using this MIB."
SYNTAX Unsigned32
VlanId ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"The VLAN-ID that uniquely identifies a VLAN. This
is the 12-bit VLAN-ID used in the VLAN Tag header.
The range is defined by the REFERENCEd specification."
REFERENCE
"IEEE Std 802.1Q 2003 Edition, Virtual Bridged
Local Area Networks."
SYNTAX Integer32 (1..4094)
VlanIdOrAny ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"The VLAN-ID that uniquely identifies a specific VLAN,
or any VLAN. The special value of 4095 is used to
indicate a wildcard, i.e., any VLAN. This can be used
in any situation where an object or table entry must
refer either to a specific VLAN or to any VLAN.
Note that a MIB object that is defined using this
TEXTUAL-CONVENTION should clarify the meaning of
'any VLAN' (i.e., the special value 4095)."
SYNTAX Integer32 (1..4094 | 4095)
VlanIdOrNone ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"The VLAN-ID that uniquely identifies a specific VLAN,
or no VLAN. The special value of zero is used to
indicate that no VLAN-ID is present or used. This can
be used in any situation where an object or a table entry
must refer either to a specific VLAN, or to no VLAN.
Note that a MIB object that is defined using this
TEXTUAL-CONVENTION should clarify the meaning of
'no VLAN' (i.e., the special value 0)."
SYNTAX Integer32 (0 | 1..4094)
VlanIdOrAnyOrNone ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"The VLAN-ID that uniquely identifies a specific VLAN,
any VLAN, or no VLAN. The special values 0 and 4095
have the same meaning as described in the VlanIdOrAny
and VlanIdOrNone TEXTUAL-CONVENTIONs.
Note that a MIB object that is defined using this
TEXTUAL-CONVENTION should clarify the meaning of
'any VLAN' and 'no VLAN' (i.e., the special values
0 and 4095)."
SYNTAX Integer32 (0 | 1..4094 | 4095)
-- -------------------------------------------------------------
-- subtrees in the Q-BRIDGE MIB
-- -------------------------------------------------------------
dot1qBase OBJECT IDENTIFIER ::= { qBridgeMIBObjects 1 }
dot1qTp OBJECT IDENTIFIER ::= { qBridgeMIBObjects 2 }
dot1qStatic OBJECT IDENTIFIER ::= { qBridgeMIBObjects 3 }
dot1qVlan OBJECT IDENTIFIER ::= { qBridgeMIBObjects 4 }
dot1vProtocol OBJECT IDENTIFIER ::= { qBridgeMIBObjects 5 }
-- -------------------------------------------------------------
-- dot1qBase subtree
-- -------------------------------------------------------------
dot1qVlanVersionNumber OBJECT-TYPE
SYNTAX INTEGER {
version1(1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The version number of IEEE 802.1Q that this device
supports."
REFERENCE
"IEEE 802.1Q/D11 Section 12.10.1.1"
::= { dot1qBase 1 }
dot1qMaxVlanId OBJECT-TYPE
SYNTAX VlanId
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum IEEE 802.1Q VLAN-ID that this device
supports."
REFERENCE
"IEEE 802.1Q/D11 Section 9.3.2.3"
::= { dot1qBase 2 }
dot1qMaxSupportedVlans OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of IEEE 802.1Q VLANs that this
device supports."
REFERENCE
"IEEE 802.1Q/D11 Section 12.10.1.1"
::= { dot1qBase 3 }
dot1qNumVlans OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current number of IEEE 802.1Q VLANs that are
configured in this device."
REFERENCE
"IEEE 802.1Q/D11 Section 12.7.1.1"
::= { dot1qBase 4 }
dot1qGvrpStatus OBJECT-TYPE
SYNTAX EnabledStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The administrative status requested by management for
GVRP. The value enabled(1) indicates that GVRP should
be enabled on this device, on all ports for which it has
not been specifically disabled. When disabled(2), GVRP
is disabled on all ports, and all GVRP packets will be
forwarded transparently. This object affects all GVRP
Applicant and Registrar state machines. A transition
from disabled(2) to enabled(1) will cause a reset of all
GVRP state machines on all ports.
The value of this object MUST be retained across
reinitializations of the management system."
DEFVAL { enabled }
::= { dot1qBase 5 }
-- -------------------------------------------------------------
-- the dot1qTp subtree
-- -------------------------------------------------------------
-- -------------------------------------------------------------
-- the current Filtering Database Table
-- -------------------------------------------------------------
dot1qFdbTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot1qFdbEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table that contains configuration and control
information for each Filtering Database currently
operating on this device. Entries in this table appear
automatically when VLANs are assigned FDB IDs in the
dot1qVlanCurrentTable."
::= { dot1qTp 1 }
dot1qFdbEntry OBJECT-TYPE
SYNTAX Dot1qFdbEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about a specific Filtering Database."
INDEX { dot1qFdbId }
::= { dot1qFdbTable 1 }
Dot1qFdbEntry ::=
SEQUENCE {
dot1qFdbId
Unsigned32,
dot1qFdbDynamicCount
Counter32
}
dot1qFdbId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The identity of this Filtering Database."
::= { dot1qFdbEntry 1 }
dot1qFdbDynamicCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current number of dynamic entries in this
Filtering Database."
REFERENCE
"IEEE 802.1Q/D11 Section 12.7.1.1.3"
::= { dot1qFdbEntry 2 }
-- -------------------------------------------------------------
-- Multiple Forwarding Databases for 802.1Q Transparent Devices
-- This table is an alternative to the dot1dTpFdbTable,
-- previously defined for 802.1D devices that only support a
-- single Forwarding Database.
-- -------------------------------------------------------------
dot1qTpFdbTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot1qTpFdbEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table that contains information about unicast entries
for which the device has forwarding and/or filtering
information. This information is used by the
transparent bridging function in determining how to
propagate a received frame."
REFERENCE
"IEEE 802.1Q/D11 Section 12.7.7"
::= { dot1qTp 2 }
dot1qTpFdbEntry OBJECT-TYPE
SYNTAX Dot1qTpFdbEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about a specific unicast MAC address for
which the device has some forwarding and/or filtering
information."
INDEX { dot1qFdbId, dot1qTpFdbAddress }
::= { dot1qTpFdbTable 1 }
Dot1qTpFdbEntry ::=
SEQUENCE {
dot1qTpFdbAddress
MacAddress,
dot1qTpFdbPort
Integer32,
dot1qTpFdbStatus
INTEGER
}
dot1qTpFdbAddress OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A unicast MAC address for which the device has
forwarding and/or filtering information."
::= { dot1qTpFdbEntry 1 }
dot1qTpFdbPort OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Either the value '0', or the port number of the port on
which a frame having a source address equal to the value
of the corresponding instance of dot1qTpFdbAddress has
been seen. A value of '0' indicates that the port
number has not been learned but that the device does
have some forwarding/filtering information about this
address (e.g., in the dot1qStaticUnicastTable).
Implementors are encouraged to assign the port value to
this object whenever it is learned, even for addresses
for which the corresponding value of dot1qTpFdbStatus is
not learned(3)."
::= { dot1qTpFdbEntry 2 }
dot1qTpFdbStatus OBJECT-TYPE
SYNTAX INTEGER {
other(1),
invalid(2),
learned(3),
self(4),
mgmt(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status of this entry. The meanings of the values
are:
other(1) - none of the following. This may include
the case where some other MIB object (not the
corresponding instance of dot1qTpFdbPort, nor an
entry in the dot1qStaticUnicastTable) is being
used to determine if and how frames addressed to
the value of the corresponding instance of
dot1qTpFdbAddress are being forwarded.
invalid(2) - this entry is no longer valid (e.g., it
was learned but has since aged out), but has not
yet been flushed from the table.
learned(3) - the value of the corresponding instance
of dot1qTpFdbPort was learned and is being used.
self(4) - the value of the corresponding instance of
dot1qTpFdbAddress represents one of the device's
addresses. The corresponding instance of
dot1qTpFdbPort indicates which of the device's
ports has this address.
mgmt(5) - the value of the corresponding instance of
dot1qTpFdbAddress is also the value of an
existing instance of dot1qStaticAddress."
::= { dot1qTpFdbEntry 3 }
-- -------------------------------------------------------------
-- Dynamic Group Registration Table
-- -------------------------------------------------------------
dot1qTpGroupTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot1qTpGroupEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing filtering information for VLANs
configured into the bridge by (local or network)
management, or learned dynamically, specifying the set of
ports to which frames received on a VLAN for this FDB
and containing a specific Group destination address are
allowed to be forwarded."
::= { dot1qTp 3 }
dot1qTpGroupEntry OBJECT-TYPE
SYNTAX Dot1qTpGroupEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Filtering information configured into the bridge by
management, or learned dynamically, specifying the set of
ports to which frames received on a VLAN and containing
a specific Group destination address are allowed to be
forwarded. The subset of these ports learned dynamically
is also provided."
INDEX { dot1qVlanIndex, dot1qTpGroupAddress }
::= { dot1qTpGroupTable 1 }
Dot1qTpGroupEntry ::=
SEQUENCE {
dot1qTpGroupAddress
MacAddress,
dot1qTpGroupEgressPorts
PortList,
dot1qTpGroupLearnt
PortList
}
dot1qTpGroupAddress OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The destination Group MAC address in a frame to which
this entry's filtering information applies."
::= { dot1qTpGroupEntry 1 }
dot1qTpGroupEgressPorts OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The complete set of ports, in this VLAN, to which
frames destined for this Group MAC address are currently
being explicitly forwarded. This does not include ports
for which this address is only implicitly forwarded, in
the dot1qForwardAllPorts list."
::= { dot1qTpGroupEntry 2 }
dot1qTpGroupLearnt OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The subset of ports in dot1qTpGroupEgressPorts that
were learned by GMRP or some other dynamic mechanism, in
this Filtering database."
::= { dot1qTpGroupEntry 3 }
-- -------------------------------------------------------------
-- Service Requirements subtree
-- -------------------------------------------------------------
dot1qForwardAllTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot1qForwardAllEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing forwarding information for each
VLAN, specifying the set of ports to which forwarding of
all multicasts applies, configured statically by
management or dynamically by GMRP. An entry appears in
this table for all VLANs that are currently
instantiated."
REFERENCE
"IEEE 802.1Q/D11 Section 12.7.2, 12.7.7"
::= { dot1qTp 4 }
dot1qForwardAllEntry OBJECT-TYPE
SYNTAX Dot1qForwardAllEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Forwarding information for a VLAN, specifying the set
of ports to which all multicasts should be forwarded,
configured statically by management or dynamically by
GMRP."
INDEX { dot1qVlanIndex }
::= { dot1qForwardAllTable 1 }
Dot1qForwardAllEntry ::=
SEQUENCE {
dot1qForwardAllPorts
PortList,
dot1qForwardAllStaticPorts
PortList,
dot1qForwardAllForbiddenPorts
PortList
}
dot1qForwardAllPorts OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The complete set of ports in this VLAN to which all
multicast group-addressed frames are to be forwarded.
This includes ports for which this need has been
determined dynamically by GMRP, or configured statically
by management."
::= { dot1qForwardAllEntry 1 }
dot1qForwardAllStaticPorts OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The set of ports configured by management in this VLAN
to which all multicast group-addressed frames are to be
forwarded. Ports entered in this list will also appear
in the complete set shown by dot1qForwardAllPorts. This
value will be restored after the device is reset. This
only applies to ports that are members of the VLAN,
defined by dot1qVlanCurrentEgressPorts. A port may not
be added in this set if it is already a member of the
set of ports in dot1qForwardAllForbiddenPorts. The
default value is a string of ones of appropriate length,
to indicate the standard behaviour of using basic
filtering services, i.e., forward all multicasts to all
ports.
The value of this object MUST be retained across
reinitializations of the management system."
::= { dot1qForwardAllEntry 2 }
dot1qForwardAllForbiddenPorts OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The set of ports configured by management in this VLAN
for which the Service Requirement attribute Forward All
Multicast Groups may not be dynamically registered by
GMRP. This value will be restored after the device is
reset. A port may not be added in this set if it is
already a member of the set of ports in
dot1qForwardAllStaticPorts. The default value is a
string of zeros of appropriate length.
The value of this object MUST be retained across
reinitializations of the management system."
::= { dot1qForwardAllEntry 3 }
dot1qForwardUnregisteredTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot1qForwardUnregisteredEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing forwarding information for each
VLAN, specifying the set of ports to which forwarding of
multicast group-addressed frames for which no
more specific forwarding information applies. This is
configured statically by management and determined
dynamically by GMRP. An entry appears in this table for
all VLANs that are currently instantiated."
REFERENCE
"IEEE 802.1Q/D11 Section 12.7.2, 12.7.7"
::= { dot1qTp 5 }
dot1qForwardUnregisteredEntry OBJECT-TYPE
SYNTAX Dot1qForwardUnregisteredEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Forwarding information for a VLAN, specifying the set
of ports to which all multicasts for which there is no
more specific forwarding information shall be forwarded.
This is configured statically by management or
dynamically by GMRP."
INDEX { dot1qVlanIndex }
::= { dot1qForwardUnregisteredTable 1 }
Dot1qForwardUnregisteredEntry ::=
SEQUENCE {
dot1qForwardUnregisteredPorts
PortList,
dot1qForwardUnregisteredStaticPorts
PortList,
dot1qForwardUnregisteredForbiddenPorts
PortList
}
dot1qForwardUnregisteredPorts OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The complete set of ports in this VLAN to which
multicast group-addressed frames for which there is no
more specific forwarding information will be forwarded.
This includes ports for which this need has been
determined dynamically by GMRP, or configured statically
by management."
::= { dot1qForwardUnregisteredEntry 1 }
dot1qForwardUnregisteredStaticPorts OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The set of ports configured by management, in this
VLAN, to which multicast group-addressed frames for
which there is no more specific forwarding information
are to be forwarded. Ports entered in this list will
also appear in the complete set shown by
dot1qForwardUnregisteredPorts. This value will be
restored after the device is reset. A port may not be
added in this set if it is already a member of the set
of ports in dot1qForwardUnregisteredForbiddenPorts. The
default value is a string of zeros of appropriate
length, although this has no effect with the default
value of dot1qForwardAllStaticPorts.
The value of this object MUST be retained across
reinitializations of the management system."
::= { dot1qForwardUnregisteredEntry 2 }
dot1qForwardUnregisteredForbiddenPorts OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The set of ports configured by management in this VLAN
for which the Service Requirement attribute Forward
Unregistered Multicast Groups may not be dynamically
registered by GMRP. This value will be restored after
the device is reset. A port may not be added in this
set if it is already a member of the set of ports in
dot1qForwardUnregisteredStaticPorts. The default value
is a string of zeros of appropriate length.
The value of this object MUST be retained across
reinitializations of the management system."
::= { dot1qForwardUnregisteredEntry 3 }
-- -------------------------------------------------------------
-- The Static (Destination-Address Filtering) Database
-- -------------------------------------------------------------
dot1qStaticUnicastTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot1qStaticUnicastEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing filtering information for Unicast
MAC addresses for each Filtering Database, configured
into the device by (local or network) management
specifying the set of ports to which frames received
from specific ports and containing specific unicast
destination addresses are allowed to be forwarded. A
value of zero in this table (as the port number from
which frames with a specific destination address are
received) is used to specify all ports for which there
is no specific entry in this table for that particular
destination address. Entries are valid for unicast
addresses only."
REFERENCE
"IEEE 802.1Q/D11 Section 12.7.7,
ISO/IEC 15802-3 Section 7.9.1"
::= { dot1qStatic 1 }
dot1qStaticUnicastEntry OBJECT-TYPE
SYNTAX Dot1qStaticUnicastEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Filtering information configured into the device by
(local or network) management specifying the set of
ports to which frames received from a specific port and
containing a specific unicast destination address are
allowed to be forwarded."
INDEX {
dot1qFdbId,
dot1qStaticUnicastAddress,
dot1qStaticUnicastReceivePort
}
::= { dot1qStaticUnicastTable 1 }
Dot1qStaticUnicastEntry ::=
SEQUENCE {
dot1qStaticUnicastAddress
MacAddress,
dot1qStaticUnicastReceivePort
Integer32,
dot1qStaticUnicastAllowedToGoTo
PortList,
dot1qStaticUnicastStatus
INTEGER
}
dot1qStaticUnicastAddress OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The destination MAC address in a frame to which this
entry's filtering information applies. This object must
take the value of a unicast address."
::= { dot1qStaticUnicastEntry 1 }
dot1qStaticUnicastReceivePort OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Either the value '0' or the port number of the port
from which a frame must be received in order for this
entry's filtering information to apply. A value of zero
indicates that this entry applies on all ports of the
device for which there is no other applicable entry."
::= { dot1qStaticUnicastEntry 2 }
dot1qStaticUnicastAllowedToGoTo OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The set of ports for which a frame with a specific
unicast address will be flooded in the event that it
has not been learned. It also specifies the set of
ports on which a specific unicast address may be dynamically
learned. The dot1qTpFdbTable will have an equivalent
entry with a dot1qTpFdbPort value of '0' until this
address has been learned, at which point it will be updated
with the port the address has been seen on. This only
applies to ports that are members of the VLAN, defined
by dot1qVlanCurrentEgressPorts. The default value of
this object is a string of ones of appropriate length.
The value of this object MUST be retained across
reinitializations of the management system."
REFERENCE
"IEEE 802.1Q/D11 Table 8-5, ISO/IEC 15802-3 Table 7-5"
::= { dot1qStaticUnicastEntry 3 }
dot1qStaticUnicastStatus OBJECT-TYPE
SYNTAX INTEGER {
other(1),
invalid(2),
permanent(3),
deleteOnReset(4),
deleteOnTimeout(5)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object indicates the status of this entry.
other(1) - this entry is currently in use, but
the conditions under which it will remain
so differ from the following values.
invalid(2) - writing this value to the object
removes the corresponding entry.
permanent(3) - this entry is currently in use
and will remain so after the next reset of
the bridge.
deleteOnReset(4) - this entry is currently in
use and will remain so until the next
reset of the bridge.
deleteOnTimeout(5) - this entry is currently in
use and will remain so until it is aged out.
The value of this object MUST be retained across
reinitializations of the management system."
DEFVAL { permanent }
::= { dot1qStaticUnicastEntry 4 }
dot1qStaticMulticastTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot1qStaticMulticastEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing filtering information for Multicast
and Broadcast MAC addresses for each VLAN, configured
into the device by (local or network) management
specifying the set of ports to which frames received
from specific ports and containing specific Multicast
and Broadcast destination addresses are allowed to be
forwarded. A value of zero in this table (as the port
number from which frames with a specific destination
address are received) is used to specify all ports for
which there is no specific entry in this table for that
particular destination address. Entries are valid for
Multicast and Broadcast addresses only."
REFERENCE
"IEEE 802.1Q/D11 Section 12.7.7,
ISO/IEC 15802-3 Section 7.9.1"
::= { dot1qStatic 2 }
dot1qStaticMulticastEntry OBJECT-TYPE
SYNTAX Dot1qStaticMulticastEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Filtering information configured into the device by
(local or network) management specifying the set of
ports to which frames received from this specific port
for this VLAN and containing this Multicast or Broadcast
destination address are allowed to be forwarded."
INDEX {
dot1qVlanIndex,
dot1qStaticMulticastAddress,
dot1qStaticMulticastReceivePort
}
::= { dot1qStaticMulticastTable 1 }
Dot1qStaticMulticastEntry ::=
SEQUENCE {
dot1qStaticMulticastAddress
MacAddress,
dot1qStaticMulticastReceivePort
Integer32,
dot1qStaticMulticastStaticEgressPorts
PortList,
dot1qStaticMulticastForbiddenEgressPorts
PortList,
dot1qStaticMulticastStatus
INTEGER
}
dot1qStaticMulticastAddress OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The destination MAC address in a frame to which this
entry's filtering information applies. This object must
take the value of a Multicast or Broadcast address."
::= { dot1qStaticMulticastEntry 1 }
dot1qStaticMulticastReceivePort OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Either the value '0' or the port number of the port
from which a frame must be received in order for this
entry's filtering information to apply. A value of zero
indicates that this entry applies on all ports of the
device for which there is no other applicable entry."
::= { dot1qStaticMulticastEntry 2 }
dot1qStaticMulticastStaticEgressPorts OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The set of ports to which frames received from a
specific port and destined for a specific Multicast or
Broadcast MAC address must be forwarded, regardless of
any dynamic information, e.g., from GMRP. A port may not
be added in this set if it is already a member of the
set of ports in dot1qStaticMulticastForbiddenEgressPorts.
The default value of this object is a string of ones of
appropriate length.
The value of this object MUST be retained across
reinitializations of the management system."
::= { dot1qStaticMulticastEntry 3 }
dot1qStaticMulticastForbiddenEgressPorts OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The set of ports to which frames received from a
specific port and destined for a specific Multicast or
Broadcast MAC address must not be forwarded, regardless
of any dynamic information, e.g., from GMRP. A port may
not be added in this set if it is already a member of the
set of ports in dot1qStaticMulticastStaticEgressPorts.
The default value of this object is a string of zeros of
appropriate length.
The value of this object MUST be retained across
reinitializations of the management system."
::= { dot1qStaticMulticastEntry 4 }
dot1qStaticMulticastStatus OBJECT-TYPE
SYNTAX INTEGER {
other(1),
invalid(2),
permanent(3),
deleteOnReset(4),
deleteOnTimeout(5)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object indicates the status of this entry.
other(1) - this entry is currently in use, but
the conditions under which it will remain
so differ from the following values.
invalid(2) - writing this value to the object
removes the corresponding entry.
permanent(3) - this entry is currently in use
and will remain so after the next reset of
the bridge.
deleteOnReset(4) - this entry is currently in
use and will remain so until the next
reset of the bridge.
deleteOnTimeout(5) - this entry is currently in
use and will remain so until it is aged out.
The value of this object MUST be retained across
reinitializations of the management system."
DEFVAL { permanent }
::= { dot1qStaticMulticastEntry 5 }
-- -------------------------------------------------------------
-- The Current VLAN Database
-- -------------------------------------------------------------
dot1qVlanNumDeletes OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times a VLAN entry has been deleted from
the dot1qVlanCurrentTable (for any reason). If an entry
is deleted, then inserted, and then deleted, this
counter will be incremented by 2."
::= { dot1qVlan 1 }
dot1qVlanCurrentTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot1qVlanCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing current configuration information
for each VLAN currently configured into the device by
(local or network) management, or dynamically created
as a result of GVRP requests received."
::= { dot1qVlan 2 }
dot1qVlanCurrentEntry OBJECT-TYPE
SYNTAX Dot1qVlanCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information for a VLAN configured into the device by
(local or network) management, or dynamically created
as a result of GVRP requests received."
INDEX { dot1qVlanTimeMark, dot1qVlanIndex }
::= { dot1qVlanCurrentTable 1 }
Dot1qVlanCurrentEntry ::=
SEQUENCE {
dot1qVlanTimeMark
TimeFilter,
dot1qVlanIndex
VlanIndex,
dot1qVlanFdbId
Unsigned32,
dot1qVlanCurrentEgressPorts
PortList,
dot1qVlanCurrentUntaggedPorts
PortList,
dot1qVlanStatus
INTEGER,
dot1qVlanCreationTime
TimeTicks
}
dot1qVlanTimeMark OBJECT-TYPE
SYNTAX TimeFilter
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A TimeFilter for this entry. See the TimeFilter
textual convention to see how this works."
::= { dot1qVlanCurrentEntry 1 }
dot1qVlanIndex OBJECT-TYPE
SYNTAX VlanIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The VLAN-ID or other identifier referring to this VLAN."
::= { dot1qVlanCurrentEntry 2 }
dot1qVlanFdbId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Filtering Database used by this VLAN. This is one
of the dot1qFdbId values in the dot1qFdbTable. This
value is allocated automatically by the device whenever
the VLAN is created: either dynamically by GVRP, or by
management, in dot1qVlanStaticTable. Allocation of this
value follows the learning constraints defined for this
VLAN in dot1qLearningConstraintsTable."
::= { dot1qVlanCurrentEntry 3 }
dot1qVlanCurrentEgressPorts OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The set of ports that are transmitting traffic for
this VLAN as either tagged or untagged frames."
REFERENCE
"IEEE 802.1Q/D11 Section 12.10.2.1"
::= { dot1qVlanCurrentEntry 4 }
dot1qVlanCurrentUntaggedPorts OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The set of ports that are transmitting traffic for
this VLAN as untagged frames."
REFERENCE
"IEEE 802.1Q/D11 Section 12.10.2.1"
::= { dot1qVlanCurrentEntry 5 }
dot1qVlanStatus OBJECT-TYPE
SYNTAX INTEGER {
other(1),
permanent(2),
dynamicGvrp(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the status of this entry.
other(1) - this entry is currently in use, but the
conditions under which it will remain so differ
from the following values.
permanent(2) - this entry, corresponding to an entry
in dot1qVlanStaticTable, is currently in use and
will remain so after the next reset of the
device. The port lists for this entry include
ports from the equivalent dot1qVlanStaticTable
entry and ports learned dynamically.
dynamicGvrp(3) - this entry is currently in use
and will remain so until removed by GVRP. There
is no static entry for this VLAN, and it will be
removed when the last port leaves the VLAN."
::= { dot1qVlanCurrentEntry 6 }
dot1qVlanCreationTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this VLAN was created."
::= { dot1qVlanCurrentEntry 7 }
-- -------------------------------------------------------------
-- The Static VLAN Database
-- -------------------------------------------------------------
dot1qVlanStaticTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot1qVlanStaticEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing static configuration information for
each VLAN configured into the device by (local or
network) management. All entries are permanent and will
be restored after the device is reset."
::= { dot1qVlan 3 }
dot1qVlanStaticEntry OBJECT-TYPE
SYNTAX Dot1qVlanStaticEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Static information for a VLAN configured into the
device by (local or network) management."
INDEX { dot1qVlanIndex }
::= { dot1qVlanStaticTable 1 }
Dot1qVlanStaticEntry ::=
SEQUENCE {
dot1qVlanStaticName
SnmpAdminString,
dot1qVlanStaticEgressPorts
PortList,
dot1qVlanForbiddenEgressPorts
PortList,
dot1qVlanStaticUntaggedPorts
PortList,
dot1qVlanStaticRowStatus
RowStatus
}
dot1qVlanStaticName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An administratively assigned string, which may be used
to identify the VLAN."
REFERENCE
"IEEE 802.1Q/D11 Section 12.10.2.1"
::= { dot1qVlanStaticEntry 1 }
dot1qVlanStaticEgressPorts OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The set of ports that are permanently assigned to the
egress list for this VLAN by management. Changes to a
bit in this object affect the per-port, per-VLAN
Registrar control for Registration Fixed for the
relevant GVRP state machine on each port. A port may
not be added in this set if it is already a member of
the set of ports in dot1qVlanForbiddenEgressPorts. The
default value of this object is a string of zeros of
appropriate length, indicating not fixed."
REFERENCE
"IEEE 802.1Q/D11 Section 12.7.7.3, 11.2.3.2.3"
::= { dot1qVlanStaticEntry 2 }
dot1qVlanForbiddenEgressPorts OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The set of ports that are prohibited by management
from being included in the egress list for this VLAN.
Changes to this object that cause a port to be included
or excluded affect the per-port, per-VLAN Registrar
control for Registration Forbidden for the relevant GVRP
state machine on each port. A port may not be added in
this set if it is already a member of the set of ports
in dot1qVlanStaticEgressPorts. The default value of
this object is a string of zeros of appropriate length,
excluding all ports from the forbidden set."
REFERENCE
"IEEE 802.1Q/D11 Section 12.7.7.3, 11.2.3.2.3"
::= { dot1qVlanStaticEntry 3 }
dot1qVlanStaticUntaggedPorts OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The set of ports that should transmit egress packets
for this VLAN as untagged. The default value of this
object for the default VLAN (dot1qVlanIndex = 1) is a string
of appropriate length including all ports. There is no
specified default for other VLANs. If a device agent cannot
support the set of ports being set, then it will reject the
set operation with an error. For example, a
manager might attempt to set more than one VLAN to be untagged
on egress where the device does not support this IEEE 802.1Q
option."
REFERENCE
"IEEE 802.1Q/D11 Section 12.10.2.1"
::= { dot1qVlanStaticEntry 4 }
dot1qVlanStaticRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates the status of this entry."
::= { dot1qVlanStaticEntry 5 }
dot1qNextFreeLocalVlanIndex OBJECT-TYPE
SYNTAX Integer32 (0|4096..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The next available value for dot1qVlanIndex of a local
VLAN entry in dot1qVlanStaticTable. This will report
values >=4096 if a new Local VLAN may be created or else
the value 0 if this is not possible.
A row creation operation in this table for an entry with a local
VlanIndex value may fail if the current value of this object
is not used as the index. Even if the value read is used,
there is no guarantee that it will still be the valid index
when the create operation is attempted; another manager may
have already got in during the intervening time interval.
In this case, dot1qNextFreeLocalVlanIndex should be re-read
and the creation re-tried with the new value.
This value will automatically change when the current value is
used to create a new row."
::= { dot1qVlan 4 }
-- -------------------------------------------------------------
-- The VLAN Port Configuration Table
-- -------------------------------------------------------------
dot1qPortVlanTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot1qPortVlanEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing per-port control and status
information for VLAN configuration in the device."
::= { dot1qVlan 5 }
dot1qPortVlanEntry OBJECT-TYPE
SYNTAX Dot1qPortVlanEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information controlling VLAN configuration for a port
on the device. This is indexed by dot1dBasePort."
AUGMENTS { dot1dBasePortEntry }
::= { dot1qPortVlanTable 1 }
Dot1qPortVlanEntry ::=
SEQUENCE {
dot1qPvid
VlanIndex,
dot1qPortAcceptableFrameTypes
INTEGER,
dot1qPortIngressFiltering
TruthValue,
dot1qPortGvrpStatus
EnabledStatus,
dot1qPortGvrpFailedRegistrations
Counter32,
dot1qPortGvrpLastPduOrigin
MacAddress,
dot1qPortRestrictedVlanRegistration
TruthValue
}
dot1qPvid OBJECT-TYPE
SYNTAX VlanIndex
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The PVID, the VLAN-ID assigned to untagged frames or
Priority-Tagged frames received on this port.
The value of this object MUST be retained across
reinitializations of the management system."
REFERENCE
"IEEE 802.1Q/D11 Section 12.10.1.1"
DEFVAL { 1 }
::= { dot1qPortVlanEntry 1 }
dot1qPortAcceptableFrameTypes OBJECT-TYPE
SYNTAX INTEGER {
admitAll(1),
admitOnlyVlanTagged(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"When this is admitOnlyVlanTagged(2), the device will
discard untagged frames or Priority-Tagged frames
received on this port. When admitAll(1), untagged
frames or Priority-Tagged frames received on this port
will be accepted and assigned to a VID based on the
PVID and VID Set for this port.
This control does not affect VLAN-independent Bridge
Protocol Data Unit (BPDU) frames, such as GVRP and
Spanning Tree Protocol (STP). It does affect VLAN-
dependent BPDU frames, such as GMRP.
The value of this object MUST be retained across
reinitializations of the management system."
REFERENCE
"IEEE 802.1Q/D11 Section 12.10.1.3"
DEFVAL { admitAll }
::= { dot1qPortVlanEntry 2 }
dot1qPortIngressFiltering OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"When this is true(1), the device will discard incoming
frames for VLANs that do not include this Port in its
Member set. When false(2), the port will accept all
incoming frames.
This control does not affect VLAN-independent BPDU
frames, such as GVRP and STP. It does affect VLAN-
dependent BPDU frames, such as GMRP.
The value of this object MUST be retained across
reinitializations of the management system."
REFERENCE
"IEEE 802.1Q/D11 Section 12.10.1.4"
DEFVAL { false }
::= { dot1qPortVlanEntry 3 }
dot1qPortGvrpStatus OBJECT-TYPE
SYNTAX EnabledStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The state of GVRP operation on this port. The value
enabled(1) indicates that GVRP is enabled on this port,
as long as dot1qGvrpStatus is also enabled for this
device. When disabled(2) but dot1qGvrpStatus is still
enabled for the device, GVRP is disabled on this port:
any GVRP packets received will be silently discarded, and
no GVRP registrations will be propagated from other
ports. This object affects all GVRP Applicant and
Registrar state machines on this port. A transition
from disabled(2) to enabled(1) will cause a reset of all
GVRP state machines on this port.
The value of this object MUST be retained across
reinitializations of the management system."
DEFVAL { enabled }
::= { dot1qPortVlanEntry 4 }
dot1qPortGvrpFailedRegistrations OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of failed GVRP registrations, for any
reason, on this port."
::= { dot1qPortVlanEntry 5 }
dot1qPortGvrpLastPduOrigin OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS read-only
STATUS