B5. Control View-2

| | | | |
| ------------- |:-------------:| -----:|
| Online Tuning (在线整定)| FALSE (缺省) TRUE 在线整定是从SMOC控制面板中按所需操作执行的。 - 控制器重新启动。 - 内部参数复位。 - 如果存在错误，控制器将挂起 | R/W | R/W|
| Initialisation（初始化） | FALSE (缺省) TRUE 当选择TRUE时，控制器将强制初始化。然后控制器从“. CON”文件读取数据并初始化内部数据。 这个操作需要在以下情况进行： - 控制器第一次启动。 - 加载新的.CON文件，以便控制器可以从这些文件中获取新的内部变量。 - 控制器由于错误而挂起。| R | R/W|
| Save SMOC（保存SMOC）| FALSE (缺省) TRUE 通过选择TRUE，所有参数将保存在DEF文件中。重启控制器时，保存的参数将用作初始值。 DEF文件每15分钟更新一次。 | R | R/W|
| Debug （调试） | 仅适用于主控制器。 Debug模式用于帮助工程师在后续时分析控制行为。当设置Debug时，数据将写入顺序Debug文件。这是一个不断增长的文件，当它达到一定的大小时，它将被复制到backup文件，且Debug文件将被清空为新条目。 Debug文件名为.DBG，backup文件名为.DCT。这些文件在“...¥EXA¥User¥Data”文件夹中创建。单击该框将提供下拉菜单TRUE / FALSE。| R | R/W|
| Debug Sample（调试示例） | 工程师需要输入debug文件在备份，清除和重新附加之前应包含的最大样本数。 默认值为10个样本。 用户可以根据实际需要选择更多数量的样本。选择非常高的样本将减少硬盘上的空间。 | R | R/W|
| Comment（评论）| 控制器的注释（16个字符）| R | R|
| Apply button（应用按钮）| 输入上述条目的参数后，新输入的数据将以蓝色显示。 单击Apply（应用）按钮。新输入的参数被保存并发送到Estimator执行。颜色变为黑色。| R/W | R/W|
| Undo button （撤消按钮）| 在单击Apply（应用）按钮之前取消新输入的参数。然后上一参数显示为黑色。 | R/W| R/W|
（R：只读，R / W：读，写或执行， - ：不显示）

---

原文：

| | | | |
| ------------- |:-------------:| -----:|
|Online Tuning | FALSE (Default) TRUE Online tuning is executed from SMOC control panel on demand operation. -Controller re-starts. -Internal parameters are reset. - Controller hangs if there exist an error |R/W |R/W|
|Initialisation |FALSE (Default) TRUE By selecting TRUE the controller will force to initialize. Then the controller reads data from “. CON” file and initializes the internal data. This operation need to be done whenever- -Controller is started first time. -New .CON files are loaded so that controller can get new internal variables from these files. - Controller hangs due to error. |R |R/W|
|Save SMOC| FALSE (Default) TRUE By selecting TRUE, the all the parameters are saved on the DEF file. When restarting the controller, saved parameters are used as initial values. The DEF file is updated every 15 minutes.| R | R/W|
|Debug | Only for Main Controller Debug mode is prepared to help engineers to analyze control behavior later. When debug is set, data is written to a sequential Debug file. This is a growing file, when it reaches a certain size, it is copied to backup file and debug file is emptied for fresh entries. Debug file name is .DBG and backup file name is .DCT. These files are created in the folder “…¥EXA¥User¥Data”. Clicking the box provides dropdown menu TRUE/FALSE| R | R/W|
|Debug Sample| Engineer need to enter maximum number of samples the debug file should contain before being backed up, cleared and appended again. Default is 10 samples. User can select more number of samples depending on actual need. Selection of very high no. of samples will reduce the space on hard disk. |R| R/W|
|Comment | Controller’s Comments (16 Characters) |R |R|
|Apply button| After entering parameters of items described above, the newly entered data are displayed in Blue. Click Apply button. The newly entered parameters are saved and be send to Estimator for execution. The color then changes to Black.| R/W| R/W|
|Undo button |Cancel a newly entered parameter before the “Apply” button is clicked. Then previous parameter is displayed in black.| R/W |R/W|
（R : Read Only, R/W : Read, Write or Execute, -：Not displayed）

---

2017.1.1