测试结果表现良好,现在把我在局域网中的部署整理如下:
思路:
当服务器A 发生故障,服务器B可以迅速接管服务器A的任务,不影响用户的正常访问。
当服务器A 故障恢复,服务器A可以马上接管服务器B的任务,服务器B恢复备机状态。
做法:
两台服务器上配置一个虚拟IP地址,主服务器先绑定虚拟ip地址,当发生故障时,备机自动接管虚拟ip地址,刷新网关路由地址。当主机恢复后,备机释放虚拟ip地址,主机再次主动接管虚拟ip地址,刷新网关路由地址。
结构图:
主服务器:ip 192.168.190.199
备服务器: ip 192.168.190.208
vip:192.168.190.88
gateWay=192.168.190.254
netMask=255.255.255.0
bcast=192.168.190.255
步骤:
1、配置虚拟ip:192.168.190.88 到 www.test.com 绑定虚拟ip
/sbin/ifconfig eth0:1 192.168.190.88 broadcast 192.168.190.255 netmask 255.255.255.0 up /sbin/route add -host 192.168.190.88 dev eth0:1
2、刷新网关路由
/sbin/arping -i eth0 -s 192.168.190.88 192.168.190.254 > /dev/null 2>&1
3、当发生故障时,主机192.168.190.199 ,释放虚拟ip192.168.190.88,备机192.168.190.208接管 虚拟ip192.168.190.88
/sbin/ifconfig eth0:1 192.168.190.88 broadcast 192.168.190.255 netmask 255.255.255.0 down /sbin/arping -i eth0 -s 192.168.190.88 192.168.190.254 > /dev/null 2>&1
3、这时 www.test.com 解析到了备机服务器192.168.190.208
4、重启备机web服务器
5、若主机192.168.190.199服务恢复正常,备机192.168.190.208释放虚拟IP,主机
绑定虚拟IP 192.168.190.88
备机释放虚拟ip:
/sbin/ifconfig eth0:1 192.168.190.88 broadcast 192.168.190.255 netmask 255.255.255.0 down /sbin/arping -i eth0 -s 192.168.190.88 192.168.190.254 > /dev/null 2>&1
6、重启启动主备机web服务
主机192.168.190.199
autoSwitchMain.sh切换脚本
#!/bin/sh ############################################################# #desc:服务器宕机自动切换服务 #author:gaozhonghui #mail:[email protected] #date:20121101 ############################################################# vip=192.168.190.88 gateWay=192.168.190.254 netMask=255.255.255.0 bcast=192.168.190.255 function_bind_vip1(){ /sbin/ifconfig eth0:1 ${vip} broadcast ${bcast} netmask ${netMask} up /sbin/route add -host ${vip} dev eth0:1 } function_remove_vip1(){ /sbin/ifconfig eth0:1 ${vip} broadcast ${bcast} netmask ${netMask down } function_vip_arping1(){ /sbin/arping -i eth0 -s ${vip} ${gateWay} > /dev/null 2>&1 } function_restart_nginx(){ /web/webserver/nginx/sbin/nginx -s reload } bind_time_vip="N" while true do httpCode_rip1=`/usr/bin/curl -o /dev/null -s -w %{http_code} http://192.168.190.199` if [ x${httpCode_rip1} == "x200" ]; then if [ ${bind_time_vip} == "N" ]; then function_bind_vip1 function_vip_arping1 bind_time_vip="Y" fi function_vip_arping1 else if [ ${bind_time_vip} == "Y" ] then function_remove_vip1 bind_time_vip="N" fi fi sleep 10 done
然后linux 启动守候进程
/usr/bin/nohup /bin/sh /home/Gzh/shell/ autoSwitchMain.sh 2>&1 > /dev/null &
备机192.168.190.208:
autoSwitchSlave.sh
#!/bin/sh ############################################################# #desc:服务器宕机自动切换服务 #author:gaozhonghui #mail:[email protected] #date:20121101 ############################################################# vip=192.168.190.88 gateWay=192.168.190.254 netMask=255.255.255.0 bcast=192.168.190.255 function_bind_vip1(){ /sbin/ifconfig eth0:1 ${vip} broadcast ${bcast} netmask ${netMask} up /sbin/route add -host ${vip} dev eth0:1 } function_remove_vip1(){ /sbin/ifconfig eth0:1 ${vip} broadcast ${bcast} netmask ${netMask} down } function_vip_arping1(){ /sbin/arping -i eth0 -s ${vip} ${gateWay} > /dev/null 2>&1 } function_restart_nginx(){ /web/webserver/nginx/sbin/nginx -s reload } bind_time_vip="N" while true do httpCode_rip1=`/usr/bin/curl -o /dev/null -s -w %{http_code} http://192. 168.190.199` if [ x${httpCode_rip1} == "x200" ]; then if [ ${bind_time_vip} == "Y" ]; then function_remove_vip1 bind_time_vip="N" fi function_vip_arping1 else if [ ${bind_time_vip} == "N" ] then function_bind_vip1 function_vip_arping1 bind_time_vip="Y" fi fi sleep 10 done
启动守候进程
/usr/bin/nohup /bin/sh /home/Gzh/shell/autoSwitchSlave.sh 2>&1 > /dev/null &
参考资料:
http://blog.s135.com/post/379/