展讯线性充电器

平台默认 pmic 线性充电

sprd_2721_charge.c 命名以 pmic 型号+charge 为规则,实现平台默认线性充电方案,文件将硬件实现和逻辑接口注册放在同一个文件中。

probe函数:

static int sprdchg_2721_probe(struct platform_device *pdev)
{
    struct sprd2721_device *sprd_2721 = NULL;
    struct sprd2721_platform_data *pdata = pdev->dev.platform_data;
    int ret = 0;
    struct power_supply *ret_ptr = NULL;
    struct power_supply_desc *charger_desc = NULL;

    printk("YGH:%s:start \n",__func__);

    reg_map = dev_get_regmap(pdev->dev.parent, NULL);
    if (!reg_map) {
        dev_err(&pdev->dev, "%s :NULL regmap for charge 2721\n",
            __func__);
        return -EINVAL;
    }
    sprd_2721 = devm_kzalloc(&pdev->dev, sizeof(*sprd_2721), GFP_KERNEL);
    if (!sprd_2721)
        return -ENOMEM;

    if (!pdata)
        //解析设备树,在其中有一个gpio_chg_cv_state、chg-ovi-gpios
        //其中chg-cv-gpio,当vbat高于cccv时触发(CCCV恒压恒流充电)
        //其中chg-ovi-gpios,充电电压较高时触发
        pdata = sprdchg_2721_parse_dt(&pdev->dev);
    if (IS_ERR_OR_NULL(pdata))
        return PTR_ERR(pdata);

    g_pdata = pdata;
    sprd_2721->dev = &pdev->dev;
    platform_set_drvdata(pdev, sprd_2721);

    if (pdata->gpio_chg_cv_state) {
        ret = devm_gpio_request(&pdev->dev,
            pdata->gpio_chg_cv_state, "chg_cv_state");
        if (ret) {
            dev_err(&pdev->dev,
                "failed to request gpio: %d\n", ret);
            return ret;
        }
        gpio_direction_input(pdata->gpio_chg_cv_state);
        pdata->irq_chg_cv_state = gpio_to_irq(pdata->gpio_chg_cv_state);

        irq_set_status_flags(pdata->irq_chg_cv_state, IRQ_NOAUTOEN);
        ret = devm_request_threaded_irq(&pdev->dev,
            pdata->irq_chg_cv_state, NULL,
            sprdchg_chg_cv_irq,
            IRQF_NO_SUSPEND | IRQF_ONESHOT,
            "sprdbat_chg_cv_state", sprd_2721);
        if (ret) {
            dev_err(&pdev->dev,
                "failed to request chg cv irq: %d\n", ret);
            return ret;
        }
    }

    if (pdata->gpio_vchg_ovi) {
        ret = devm_gpio_request(&pdev->dev,
            pdata->gpio_vchg_ovi, "vchg_ovi");
        if (ret) {
            dev_err(&pdev->dev,
                "failed to request gpio: %d\n", ret);
            return ret;
        }
        gpio_direction_input(pdata->gpio_vchg_ovi);
        pdata->irq_vchg_ovi = gpio_to_irq(pdata->gpio_vchg_ovi);

        irq_set_status_flags(pdata->irq_vchg_ovi, IRQ_NOAUTOEN);
        ret = devm_request_threaded_irq(&pdev->dev,
            pdata->irq_vchg_ovi, NULL,
            sprdchg_vchg_ovi_irq,
            IRQF_NO_SUSPEND | IRQF_ONESHOT,
            "sprdbat_vchg_ovi", sprd_2721);
        if (ret) {
            dev_err(&pdev->dev,
                "failed to request chg ovi irq: %d\n", ret);
            return ret;
        }
    }
    
    //如果CONFIG_OTP_SPRD_PMIC_EFUSE这个选项有的话,就会调用,然后获取cv的电压值
    sprdchg_cccv_cal_get();
    
    //注册回调函数
    sprdbat_register_ext_ops(&sprd_2721_op);
    charger_desc = devm_kzalloc(&pdev->dev,
        sizeof(*charger_desc), GFP_KERNEL);
    if (charger_desc == NULL) {
        ret = -ENOMEM;
        sprd_2721 = NULL;
        return ret;
    }
    
    //注册内部充电的power_supply
    sprd_2721->charger.desc = charger_desc;
    charger_desc->name = CHG_PSY_INNER;
    charger_desc->type = POWER_SUPPLY_TYPE_UNKNOWN;
    charger_desc->get_property = sprd2721_get_property;
    ret_ptr = power_supply_register(&pdev->dev,
        sprd_2721->charger.desc, NULL);
    if (IS_ERR(ret_ptr)) {
        dev_err(&pdev->dev, "failed to register sprd_2721 psy: %p\n",
            ret_ptr);
        return PTR_ERR(ret_ptr);
    }
    SPRDCHG_DEBUG("%s probe ok\n", __func__);
        printk("YGH:%s:end \n",__func__);
    return 0;
}

其中来简单介绍下sprd_2721_op的回调函数的:

static struct sprd_ext_ic_operations sprd_2720_op = {
    .ic_init = sprdchg_chip_init,
    .charge_start_ext = sprdchg_start_charge,
    .set_charge_cur = sprdchg_set_chg_cur,
    .charge_stop_ext = sprdchg_stop_charge,
    .get_charging_status = sprdchg_get_cccvstate,
    .get_charging_fault =  sprdchg_get_charge_fault,
    .get_charge_cur_ext = sprdchg_get_chg_cur,
    .set_termina_vol_ext = sprdchg_termina_vol_set,
};

其中sprdchg_chip_init函数是初始化充电芯片的:

static void sprdchg_chip_init(struct sprdbat_drivier_data *bdata)
{
    if (bdata == NULL)
        return;
    bat_drv_data = bdata;
    glb_adi_write(ANA_REG_GLB_CHGR_CTRL0,
        BIT_CHGR_CC_EN, BIT_CHGR_CC_EN);
    chg_adi_write(ANA_REG_GLB_CHGR_CTRL0,
              BITS_CHGR_CV_V(0U), BITS_CHGR_CV_V(~0U));

    chg_adi_write(ANA_REG_GLB_CHGR_CTRL0,
              BITS_CHGR_DPM(3), BITS_CHGR_DPM(~0U));

    sprdchg_termina_vol_set(bat_drv_data->pdata->chg_end_vol_pure);
    sprdchg_set_chg_ovp(bat_drv_data->pdata->ovp_stop);
    sprdchg_set_eoc_level(0);
}

sprdchg_start_charge函数:

static void sprdchg_start_charge(void)
{
    chg_adi_write(ANA_REG_GLB_CHGR_CTRL0, 0, BIT_CHGR_PD);
    _sprdchg_set_recharge();
}

设置充电状态,并且设置复充状态位

设置充电sprdchg_set_chg_cur电流:

线性充电方案充电电流设置下限为 300mA,电流上限为 2300mA,300mA – 1400mA 设置最小步进单位为 50mA,1400mA – 2300mA 设置最小步进单位为 100mA。


static void sprdchg_set_chg_cur(uint32_t chg_current)
{
    uint32_t temp;

    if (bat_drv_data == NULL)
        return;
    if (bat_drv_data->bat_info.chg_current_type_limit < chg_current)
        bat_drv_data->bat_info.chg_current_type_limit = chg_current;

    if (chg_current > SPRDBAT_CHG_CUR_LEVEL_MAX)
        chg_current = SPRDBAT_CHG_CUR_LEVEL_MAX;

    if (chg_current < SPRDBAT_CHG_CUR_LEVEL_MIN)
        chg_current = SPRDBAT_CHG_CUR_LEVEL_MIN;

    if (chg_current < 1400) {
        temp = ((chg_current - 300) / 50);
    } else {
        temp = ((chg_current - 1400) / 100);
        temp += 0x16;
    }


    chg_adi_write(ANA_REG_GLB_CHGR_CTRL0, 0,
        BIT_CHGR_CC_EN);

    chg_adi_write(ANA_REG_GLB_CHGR_CTRL1,
              BITS_CHGR_CC_I(temp),
              BITS_CHGR_CC_I(~0U));

    chg_adi_write(ANA_REG_GLB_CHGR_CTRL0,
        BIT_CHGR_CC_EN, BIT_CHGR_CC_EN);
}

开关充电充电电流需要根据使用的 IC 不同区分设置。

sprdchg_stop_charge函数

停止充电

sprdchg_get_cccvstate函数


static int sprdchg_get_cccvstate(void)
{
    SPRDCHG_DEBUG("sprdbat:cv state:0x%x, iterm:0x%x",
        chg_adi_read(ANA_REG_GLB_CHGR_STATUS),
        chg_adi_read(ANA_REG_GLB_CHGR_CTRL0));
    return ((chg_adi_read(ANA_REG_GLB_CHGR_STATUS) &
        BIT_CHGR_CV_STATUS) ? 1 : 0);
}

sprdchg_get_charge_fault是个空函数

sprdchg_set_cccvpoint暂且不清楚

sprdchg_get_chg_cur暂且不清楚

你可能感兴趣的:(展讯线性充电器)