此文内容从网络收集，介绍了Linux系统 /proc/sys/net/ipv4/ 目录下所有内核参数的含义，由于每篇文章字数的限制，此文被分成了两个部分，这是第二部分。
icmp_errors_use_inbound_ifaddr - BOOLEAN
If zero, icmp error messages are sent with the primary address of
the exiting interface.
If non-zero, the message will be sent with the primary address of
the interface that received the packet that caused the icmp error.
This is the behaviour network many administrators will expect from
a router. And it can make debugging complicated network layouts
much easier.
Note that if no primary address exists for the interface selected,
then the primary address of the first non-loopback interface that
has one will be used regardless of this setting.
Default: 0
igmp_max_memberships - INTEGER
Change the maximum number of multicast groups we can subscribe to.
Default: 20
Theoretical maximum value is bounded by having to send a membership
report in a single datagram (i.e. the report can't span multiple
datagrams, or risk confusing the switch and leaving groups you don't
intend to).
The number of supported groups 'M' is bounded by the number of group
report entries you can fit into a single datagram of 65535 bytes.
M = 65536-sizeof (ip header)/(sizeof(Group record))
Group records are variable length, with a minimum of 12 bytes.
So net.ipv4.igmp_max_memberships should not be set higher than:
(65536-24) / 12 = 5459
The value 5459 assumes no IP header options, so in practice
this number may be lower.
igmp_max_msf - INTEGER
Maximum number of addresses allowed in the source filter list for a
multicast group.
Default: 10
igmp_qrv - INTEGER
Controls the IGMP query robustness variable (see RFC2236 8.1).
Default: 2 (as specified by RFC2236 8.1)
Minimum: 1 (as specified by RFC6636 4.5)
force_igmp_version - INTEGER
0 - (default) No enforcement of a IGMP version, IGMPv1/v2 fallback
allowed. Will back to IGMPv3 mode again if all IGMPv1/v2 Querier
Present timer expires.
1 - Enforce to use IGMP version 1. Will also reply IGMPv1 report if
receive IGMPv2/v3 query.
2 - Enforce to use IGMP version 2. Will fallback to IGMPv1 if receive
IGMPv1 query message. Will reply report if receive IGMPv3 query.
3 - Enforce to use IGMP version 3. The same react with default 0.
Note: this is not the same with force_mld_version because IGMPv3 RFC3376
Security Considerations does not have clear description that we could
ignore other version messages completely as MLDv2 RFC3810. So make
this value as default 0 is recommended.
conf/interface/* changes special settings per interface (where
"interface" is the name of your network interface)
conf/all/* is special, changes the settings for all interfaces
log_martians - BOOLEAN
Log packets with impossible addresses to kernel log.
log_martians for the interface will be enabled if at least one of
conf/{all,interface}/log_martians is set to TRUE,
it will be disabled otherwise
accept_redirects - BOOLEAN
Accept ICMP redirect messages.
accept_redirects for the interface will be enabled if:
- both conf/{all,interface}/accept_redirects are TRUE in the case
forwarding for the interface is enabled
or
- at least one of conf/{all,interface}/accept_redirects is TRUE in the
case forwarding for the interface is disabled
accept_redirects for the interface will be disabled otherwise
default TRUE (host)
FALSE (router)
forwarding - BOOLEAN
Enable IP forwarding on this interface. This controls whether packets
received _on_ this interface can be forwarded.
mc_forwarding - BOOLEAN
Do multicast routing. The kernel needs to be compiled with CONFIG_MROUTE
and a multicast routing daemon is required.
conf/all/mc_forwarding must also be set to TRUE to enable multicast
routing for the interface
medium_id - INTEGER
Integer value used to differentiate the devices by the medium they
are attached to. Two devices can have different id values when
the broadcast packets are received only on one of them.
The default value 0 means that the device is the only interface
to its medium, value of -1 means that medium is not known.
Currently, it is used to change the proxy_arp behavior:
the proxy_arp feature is enabled for packets forwarded between
two devices attached to different media.
proxy_arp - BOOLEAN
Do proxy arp.
proxy_arp for the interface will be enabled if at least one of
conf/{all,interface}/proxy_arp is set to TRUE,
it will be disabled otherwise
proxy_arp_pvlan - BOOLEAN
Private VLAN proxy arp.
Basically allow proxy arp replies back to the same interface
(from which the ARP request/solicitation was received).
This is done to support (ethernet) switch features, like RFC
3069, where the individual ports are NOT allowed to
communicate with each other, but they are allowed to talk to
the upstream router. As described in RFC 3069, it is possible
to allow these hosts to communicate through the upstream
router by proxy_arp'ing. Don't need to be used together with
proxy_arp.
This technology is known by different names:
In RFC 3069 it is called VLAN Aggregation.
Cisco and Allied Telesyn call it Private VLAN.
Hewlett-Packard call it Source-Port filtering or port-isolation.
Ericsson call it MAC-Forced Forwarding (RFC Draft).
shared_media - BOOLEAN
Send(router) or accept(host) RFC1620 shared media redirects.
Overrides secure_redirects.
shared_media for the interface will be enabled if at least one of
conf/{all,interface}/shared_media is set to TRUE,
it will be disabled otherwise
default TRUE
secure_redirects - BOOLEAN
Accept ICMP redirect messages only to gateways listed in the
interface's current gateway list. Even if disabled, RFC1122 redirect
rules still apply.
Overridden by shared_media.
secure_redirects for the interface will be enabled if at least one of
conf/{all,interface}/secure_redirects is set to TRUE,
it will be disabled otherwise
default TRUE
send_redirects - BOOLEAN
Send redirects, if router.
send_redirects for the interface will be enabled if at least one of
conf/{all,interface}/send_redirects is set to TRUE,
it will be disabled otherwise
Default: TRUE
bootp_relay - BOOLEAN
Accept packets with source address 0.b.c.d destined
not to this host as local ones. It is supposed, that
BOOTP relay daemon will catch and forward such packets.
conf/all/bootp_relay must also be set to TRUE to enable BOOTP relay
for the interface
default FALSE
Not Implemented Yet.
accept_source_route - BOOLEAN
Accept packets with SRR option.
conf/all/accept_source_route must also be set to TRUE to accept packets
with SRR option on the interface
default TRUE (router)
FALSE (host)
accept_local - BOOLEAN
Accept packets with local source addresses. In combination with
suitable routing, this can be used to direct packets between two
local interfaces over the wire and have them accepted properly.
default FALSE
route_localnet - BOOLEAN
Do not consider loopback addresses as martian source or destination
while routing. This enables the use of 127/8 for local routing purposes.
default FALSE
rp_filter - INTEGER
0 - No source validation.
1 - Strict mode as defined in RFC3704 Strict Reverse Path
Each incoming packet is tested against the FIB and if the interface
is not the best reverse path the packet check will fail.
By default failed packets are discarded.
2 - Loose mode as defined in RFC3704 Loose Reverse Path
Each incoming packet's source address is also tested against the FIB
and if the source address is not reachable via any interface
the packet check will fail.
Current recommended practice in RFC3704 is to enable strict mode
to prevent IP spoofing from DDos attacks. If using asymmetric routing
or other complicated routing, then loose mode is recommended.
The max value from conf/{all,interface}/rp_filter is used
when doing source validation on the {interface}.
Default value is 0. Note that some distributions enable it
in startup scripts.
arp_filter - BOOLEAN
1 - Allows you to have multiple network interfaces on the same
subnet, and have the ARPs for each interface be answered
based on whether or not the kernel would route a packet from
the ARP'd IP out that interface (therefore you must use source
based routing for this to work). In other words it allows control
of which cards (usually 1) will respond to an arp request.
0 - (default) The kernel can respond to arp requests with addresses
from other interfaces. This may seem wrong but it usually makes
sense, because it increases the chance of successful communication.
IP addresses are owned by the complete host on Linux, not by
particular interfaces. Only for more complex setups like load-
balancing, does this behaviour cause problems.
arp_filter for the interface will be enabled if at least one of
conf/{all,interface}/arp_filter is set to TRUE,
it will be disabled otherwise
arp_announce - INTEGER
Define different restriction levels for announcing the local
source IP address from IP packets in ARP requests sent on
interface:
0 - (default) Use any local address, configured on any interface
1 - Try to avoid local addresses that are not in the target's
subnet for this interface. This mode is useful when target
hosts reachable via this interface require the source IP
address in ARP requests to be part of their logical network
configured on the receiving interface. When we generate the
request we will check all our subnets that include the
target IP and will preserve the source address if it is from
such subnet. If there is no such subnet we select source
address according to the rules for level 2.
2 - Always use the best local address for this target.
In this mode we ignore the source address in the IP packet
and try to select local address that we prefer for talks with
the target host. Such local address is selected by looking
for primary IP addresses on all our subnets on the outgoing
interface that include the target IP address. If no suitable
local address is found we select the first local address
we have on the outgoing interface or on all other interfaces,
with the hope we will receive reply for our request and
even sometimes no matter the source IP address we announce.
The max value from conf/{all,interface}/arp_announce is used.
Increasing the restriction level gives more chance for
receiving answer from the resolved target while decreasing
the level announces more valid sender's information.
arp_ignore - INTEGER
Define different modes for sending replies in response to
received ARP requests that resolve local target IP addresses:
0 - (default): reply for any local target IP address, configured
on any interface
1 - reply only if the target IP address is local address
configured on the incoming interface
2 - reply only if the target IP address is local address
configured on the incoming interface and both with the
sender's IP address are part from same subnet on this interface
3 - do not reply for local addresses configured with scope host,
only resolutions for global and link addresses are replied
4-7 - reserved
8 - do not reply for all local addresses
The max value from conf/{all,interface}/arp_ignore is used
when ARP request is received on the {interface}
arp_notify - BOOLEAN
Define mode for notification of address and device changes.
0 - (default): do nothing
1 - Generate gratuitous arp requests when device is brought up
or hardware address changes.
arp_accept - BOOLEAN
Define behavior for gratuitous ARP frames who's IP is not
already present in the ARP table:
0 - don't create new entries in the ARP table
1 - create new entries in the ARP table
Both replies and requests type gratuitous arp will trigger the
ARP table to be updated, if this setting is on.
If the ARP table already contains the IP address of the
gratuitous arp frame, the arp table will be updated regardless
if this setting is on or off.
mcast_solicit - INTEGER
The maximum number of multicast probes in INCOMPLETE state,
when the associated hardware address is unknown. Defaults
to 3.
ucast_solicit - INTEGER
The maximum number of unicast probes in PROBE state, when
the hardware address is being reconfirmed. Defaults to 3.
app_solicit - INTEGER
The maximum number of probes to send to the user space ARP daemon
via netlink before dropping back to multicast probes (see
mcast_resolicit). Defaults to 0.
mcast_resolicit - INTEGER
The maximum number of multicast probes after unicast and
app probes in PROBE state. Defaults to 0.
disable_policy - BOOLEAN
Disable IPSEC policy (SPD) for this interface
disable_xfrm - BOOLEAN
Disable IPSEC encryption on this interface, whatever the policy
igmpv2_unsolicited_report_interval - INTEGER
The interval in milliseconds in which the next unsolicited
IGMPv1 or IGMPv2 report retransmit will take place.
Default: 10000 (10 seconds)
igmpv3_unsolicited_report_interval - INTEGER
The interval in milliseconds in which the next unsolicited
IGMPv3 report retransmit will take place.
Default: 1000 (1 seconds)
promote_secondaries - BOOLEAN
When a primary IP address is removed from this interface
promote a corresponding secondary IP address instead of
removing all the corresponding secondary IP addresses.
drop_unicast_in_l2_multicast - BOOLEAN
Drop any unicast IP packets that are received in link-layer
multicast (or broadcast) frames.
This behavior (for multicast) is actually a SHOULD in RFC
1122, but is disabled by default for compatibility reasons.
Default: off (0)
drop_gratuitous_arp - BOOLEAN
Drop all gratuitous ARP frames, for example if there's a known
good ARP proxy on the network and such frames need not be used
(or in the case of 802.11, must not be used to prevent attacks.)
Default: off (0)
tag - INTEGER
Allows you to write a number, which can be used as required.
Default value is 0.
xfrm4_gc_thresh - INTEGER
The threshold at which we will start garbage collecting for IPv4
destination cache entries. At twice this value the system will
refuse new allocations.
igmp_link_local_mcast_reports - BOOLEAN
Enable IGMP reports for link local multicast groups in the
224.0.0.X range.
Default TRUE
Alexey Kuznetsov.
[email protected]
Updated by:
Andi Kleen
[email protected]
Nicolas Delon
[email protected]
/proc/sys/net/ipv6/* Variables:
IPv6 has no global variables such as tcp_. tcp_ settings under ipv4/ also
apply to IPv6 [XXX?].
bindv6only - BOOLEAN
Default value for IPV6_V6ONLY socket option,
which restricts use of the IPv6 socket to IPv6 communication
only.
TRUE: disable IPv4-mapped address feature
FALSE: enable IPv4-mapped address feature
Default: FALSE (as specified in RFC3493)
flowlabel_consistency - BOOLEAN
Protect the consistency (and unicity) of flow label.
You have to disable it to use IPV6_FL_F_REFLECT flag on the
flow label manager.
TRUE: enabled
FALSE: disabled
Default: TRUE
auto_flowlabels - INTEGER
Automatically generate flow labels based on a flow hash of the
packet. This allows intermediate devices, such as routers, to
identify packet flows for mechanisms like Equal Cost Multipath
Routing (see RFC 6438).
0: automatic flow labels are completely disabled
1: automatic flow labels are enabled by default, they can be
disabled on a per socket basis using the IPV6_AUTOFLOWLABEL
socket option
2: automatic flow labels are allowed, they may be enabled on a
per socket basis using the IPV6_AUTOFLOWLABEL socket option
3: automatic flow labels are enabled and enforced, they cannot
be disabled by the socket option
Default: 1
flowlabel_state_ranges - BOOLEAN
Split the flow label number space into two ranges. 0-0x7FFFF is
reserved for the IPv6 flow manager facility, 0x80000-0xFFFFF
is reserved for stateless flow labels as described in RFC6437.
TRUE: enabled
FALSE: disabled
Default: true
flowlabel_reflect - BOOLEAN
Automatically reflect the flow label. Needed for Path MTU
Discovery to work with Equal Cost Multipath Routing in anycast
environments. See RFC 7690 and:
https://tools.ietf.org/html/draft-wang-6man-flow-label-reflection-01
TRUE: enabled
FALSE: disabled
Default: FALSE
anycast_src_echo_reply - BOOLEAN
Controls the use of anycast addresses as source addresses for ICMPv6
echo reply
TRUE: enabled
FALSE: disabled
Default: FALSE
idgen_delay - INTEGER
Controls the delay in seconds after which time to retry
privacy stable address generation if a DAD conflict is
detected.
Default: 1 (as specified in RFC7217)
idgen_retries - INTEGER
Controls the number of retries to generate a stable privacy
address if a DAD conflict is detected.
Default: 3 (as specified in RFC7217)
mld_qrv - INTEGER
Controls the MLD query robustness variable (see RFC3810 9.1).
Default: 2 (as specified by RFC3810 9.1)
Minimum: 1 (as specified by RFC6636 4.5)
max_dst_opts_cnt - INTEGER
Maximum number of non-padding TLVs allowed in a Destination
options extension header. If this value is less than zero
then unknown options are disallowed and the number of known
TLVs allowed is the absolute value of this number.
Default: 8
max_hbh_opts_cnt - INTEGER
Maximum number of non-padding TLVs allowed in a Hop-by-Hop
options extension header. If this value is less than zero
then unknown options are disallowed and the number of known
TLVs allowed is the absolute value of this number.
Default: 8
max dst_opts_len - INTEGER
Maximum length allowed for a Destination options extension
header.
Default: INT_MAX (unlimited)
max hbh_opts_len - INTEGER
Maximum length allowed for a Hop-by-Hop options extension
header.
Default: INT_MAX (unlimited)
IPv6 Fragmentation:
ip6frag_high_thresh - INTEGER
Maximum memory used to reassemble IPv6 fragments. When
ip6frag_high_thresh bytes of memory is allocated for this purpose,
the fragment handler will toss packets until ip6frag_low_thresh
is reached.
ip6frag_low_thresh - INTEGER
See ip6frag_high_thresh
ip6frag_time - INTEGER
Time in seconds to keep an IPv6 fragment in memory.
conf/default/*:
Change the interface-specific default settings.
conf/all/*:
Change all the interface-specific settings.
[XXX: Other special features than forwarding?]
conf/all/forwarding - BOOLEAN
Enable global IPv6 forwarding between all interfaces.
IPv4 and IPv6 work differently here; e.g. netfilter must be used
to control which interfaces may forward packets and which not.
This also sets all interfaces' Host/Router setting
'forwarding' to the specified value. See below for details.
This referred to as global forwarding.
proxy_ndp - BOOLEAN
Do proxy ndp.
fwmark_reflect - BOOLEAN
Controls the fwmark of kernel-generated IPv6 reply packets that are not
associated with a socket for example, TCP RSTs or ICMPv6 echo replies).
If unset, these packets have a fwmark of zero. If set, they have the
fwmark of the packet they are replying to.
Default: 0
conf/interface/*:
Change special settings per interface.
The functional behaviour for certain settings is different
depending on whether local forwarding is enabled or not.
accept_ra - INTEGER
Accept Router Advertisements; autoconfigure using them.
It also determines whether or not to transmit Router
Solicitations. If and only if the functional setting is to
accept Router Advertisements, Router Solicitations will be
transmitted.
Possible values are:
0 Do not accept Router Advertisements.
1 Accept Router Advertisements if forwarding is disabled.
2 Overrule forwarding behaviour. Accept Router Advertisements
even if forwarding is enabled.
Functional default: enabled if local forwarding is disabled.
disabled if local forwarding is enabled.
accept_ra_defrtr - BOOLEAN
Learn default router in Router Advertisement.
Functional default: enabled if accept_ra is enabled.
disabled if accept_ra is disabled.
accept_ra_from_local - BOOLEAN
Accept RA with source-address that is found on local machine
if the RA is otherwise proper and able to be accepted.
Default is to NOT accept these as it may be an un-intended
network loop.
Functional default:
enabled if accept_ra_from_local is enabled
on a specific interface.
disabled if accept_ra_from_local is disabled
on a specific interface.
accept_ra_min_hop_limit - INTEGER
Minimum hop limit Information in Router Advertisement.
Hop limit Information in Router Advertisement less than this
variable shall be ignored.
Default: 1
accept_ra_pinfo - BOOLEAN
Learn Prefix Information in Router Advertisement.
Functional default: enabled if accept_ra is enabled.
disabled if accept_ra is disabled.
accept_ra_rt_info_min_plen - INTEGER
Minimum prefix length of Route Information in RA.
Route Information w/ prefix smaller than this variable shall
be ignored.
Functional default: 0 if accept_ra_rtr_pref is enabled.
-1 if accept_ra_rtr_pref is disabled.
accept_ra_rt_info_max_plen - INTEGER
Maximum prefix length of Route Information in RA.
Route Information w/ prefix larger than this variable shall
be ignored.
Functional default: 0 if accept_ra_rtr_pref is enabled.
-1 if accept_ra_rtr_pref is disabled.
accept_ra_rtr_pref - BOOLEAN
Accept Router Preference in RA.
Functional default: enabled if accept_ra is enabled.
disabled if accept_ra is disabled.
accept_ra_mtu - BOOLEAN
Apply the MTU value specified in RA option 5 (RFC4861). If
disabled, the MTU specified in the RA will be ignored.
Functional default: enabled if accept_ra is enabled.
disabled if accept_ra is disabled.
accept_redirects - BOOLEAN
Accept Redirects.
Functional default: enabled if local forwarding is disabled.
disabled if local forwarding is enabled.
accept_source_route - INTEGER
Accept source routing (routing extension header).
>= 0: Accept only routing header type 2.
< 0: Do not accept routing header.
Default: 0
autoconf - BOOLEAN
Autoconfigure addresses using Prefix Information in Router
Advertisements.
Functional default: enabled if accept_ra_pinfo is enabled.
disabled if accept_ra_pinfo is disabled.
dad_transmits - INTEGER
The amount of Duplicate Address Detection probes to send.
Default: 1
forwarding - INTEGER
Configure interface-specific Host/Router behaviour.
Note: It is recommended to have the same setting on all
interfaces; mixed router/host scenarios are rather uncommon.
Possible values are:
0 Forwarding disabled
1 Forwarding enabled
FALSE (0):
By default, Host behaviour is assumed. This means:
1. IsRouter flag is not set in Neighbour Advertisements.
2. If accept_ra is TRUE (default), transmit Router
Solicitations.
3. If accept_ra is TRUE (default), accept Router
Advertisements (and do autoconfiguration).
4. If accept_redirects is TRUE (default), accept Redirects.
TRUE (1):
If local forwarding is enabled, Router behaviour is assumed.
This means exactly the reverse from the above:
1. IsRouter flag is set in Neighbour Advertisements.
2. Router Solicitations are not sent unless accept_ra is 2.
3. Router Advertisements are ignored unless accept_ra is 2.
4. Redirects are ignored.
Default: 0 (disabled) if global forwarding is disabled (default),
otherwise 1 (enabled).
hop_limit - INTEGER
Default Hop Limit to set.
Default: 64
mtu - INTEGER
Default Maximum Transfer Unit
Default: 1280 (IPv6 required minimum)
ip_nonlocal_bind - BOOLEAN
If set, allows processes to bind() to non-local IPv6 addresses,
which can be quite useful - but may break some applications.
Default: 0
router_probe_interval - INTEGER
Minimum interval (in seconds) between Router Probing described
in RFC4191.
Default: 60
router_solicitation_delay - INTEGER
Number of seconds to wait after interface is brought up
before sending Router Solicitations.
Default: 1
router_solicitation_interval - INTEGER
Number of seconds to wait between Router Solicitations.
Default: 4
router_solicitations - INTEGER
Number of Router Solicitations to send until assuming no
routers are present.
Default: 3
use_oif_addrs_only - BOOLEAN
When enabled, the candidate source addresses for destinations
routed via this interface are restricted to the set of addresses
configured on this interface (vis. RFC 6724, section 4).
Default: false
use_tempaddr - INTEGER
Preference for Privacy Extensions (RFC3041).
<= 0 : disable Privacy Extensions
== 1 : enable Privacy Extensions, but prefer public
addresses over temporary addresses.
> 1 : enable Privacy Extensions and prefer temporary
addresses over public addresses.
Default: 0 (for most devices)
-1 (for point-to-point devices and loopback devices)
temp_valid_lft - INTEGER
valid lifetime (in seconds) for temporary addresses.
Default: 604800 (7 days)
temp_prefered_lft - INTEGER
Preferred lifetime (in seconds) for temporary addresses.
Default: 86400 (1 day)
keep_addr_on_down - INTEGER
Keep all IPv6 addresses on an interface down event. If set static
global addresses with no expiration time are not flushed.
>0 : enabled
0 : system default
<0 : disabled
Default: 0 (addresses are removed)
max_desync_factor - INTEGER
Maximum value for DESYNC_FACTOR, which is a random value
that ensures that clients don't synchronize with each
other and generate new addresses at exactly the same time.
value is in seconds.
Default: 600
regen_max_retry - INTEGER
Number of attempts before give up attempting to generate
valid temporary addresses.
Default: 5
max_addresses - INTEGER
Maximum number of autoconfigured addresses per interface. Setting
to zero disables the limitation. It is not recommended to set this
value too large (or to zero) because it would be an easy way to
crash the kernel by allowing too many addresses to be created.
Default: 16
disable_ipv6 - BOOLEAN
Disable IPv6 operation. If accept_dad is set to 2, this value
will be dynamically set to TRUE if DAD fails for the link-local
address.
Default: FALSE (enable IPv6 operation)
When this value is changed from 1 to 0 (IPv6 is being enabled),
it will dynamically create a link-local address on the given
interface and start Duplicate Address Detection, if necessary.
When this value is changed from 0 to 1 (IPv6 is being disabled),
it will dynamically delete all address on the given interface.
accept_dad - INTEGER
Whether to accept DAD (Duplicate Address Detection).
0: Disable DAD
1: Enable DAD (default)
2: Enable DAD, and disable IPv6 operation if MAC-based duplicate
link-local address has been found.
DAD operation and mode on a given interface will be selected according
to the maximum value of conf/{all,interface}/accept_dad.
force_tllao - BOOLEAN
Enable sending the target link-layer address option even when
responding to a unicast neighbor solicitation.
Default: FALSE
Quoting from RFC 2461, section 4.4, Target link-layer address:
"The option MUST be included for multicast solicitations in order to
avoid infinite Neighbor Solicitation "recursion" when the peer node
does not have a cache entry to return a Neighbor Advertisements
message. When responding to unicast solicitations, the option can be
omitted since the sender of the solicitation has the correct link-
layer address; otherwise it would not have be able to send the unicast
solicitation in the first place. However, including the link-layer
address in this case adds little overhead and eliminates a potential
race condition where the sender deletes the cached link-layer address
prior to receiving a response to a previous solicitation."
ndisc_notify - BOOLEAN
Define mode for notification of address and device changes.
0 - (default): do nothing
1 - Generate unsolicited neighbour advertisements when device is brought
up or hardware address changes.
ndisc_tclass - INTEGER
The IPv6 Traffic Class to use by default when sending IPv6 Neighbor
Discovery (Router Solicitation, Router Advertisement, Neighbor
Solicitation, Neighbor Advertisement, Redirect) messages.
These 8 bits can be interpreted as 6 high order bits holding the DSCP
value and 2 low order bits representing ECN (which you probably want
to leave cleared).
0 - (default)
mldv1_unsolicited_report_interval - INTEGER
The interval in milliseconds in which the next unsolicited
MLDv1 report retransmit will take place.
Default: 10000 (10 seconds)
mldv2_unsolicited_report_interval - INTEGER
The interval in milliseconds in which the next unsolicited
MLDv2 report retransmit will take place.
Default: 1000 (1 second)
force_mld_version - INTEGER
0 - (default) No enforcement of a MLD version, MLDv1 fallback allowed
1 - Enforce to use MLD version 1
2 - Enforce to use MLD version 2
suppress_frag_ndisc - INTEGER
Control RFC 6980 (Security Implications of IPv6 Fragmentation
with IPv6 Neighbor Discovery) behavior:
1 - (default) discard fragmented neighbor discovery packets
0 - allow fragmented neighbor discovery packets
optimistic_dad - BOOLEAN
Whether to perform Optimistic Duplicate Address Detection (RFC 4429).
0: disabled (default)
1: enabled
Optimistic Duplicate Address Detection for the interface will be enabled
if at least one of conf/{all,interface}/optimistic_dad is set to 1,
it will be disabled otherwise.
use_optimistic - BOOLEAN
If enabled, do not classify optimistic addresses as deprecated during
source address selection. Preferred addresses will still be chosen
before optimistic addresses, subject to other ranking in the source
address selection algorithm.
0: disabled (default)
1: enabled
This will be enabled if at least one of
conf/{all,interface}/use_optimistic is set to 1, disabled otherwise.
stable_secret - IPv6 address
This IPv6 address will be used as a secret to generate IPv6
addresses for link-local addresses and autoconfigured
ones. All addresses generated after setting this secret will
be stable privacy ones by default. This can be changed via the
addrgenmode ip-link. conf/default/stable_secret is used as the
secret for the namespace, the interface specific ones can
overwrite that. Writes to conf/all/stable_secret are refused.
It is recommended to generate this secret during installation
of a system and keep it stable after that.
By default the stable secret is unset.
drop_unicast_in_l2_multicast - BOOLEAN
Drop any unicast IPv6 packets that are received in link-layer
multicast (or broadcast) frames.
By default this is turned off.
drop_unsolicited_na - BOOLEAN
Drop all unsolicited neighbor advertisements, for example if there's
a known good NA proxy on the network and such frames need not be used
(or in the case of 802.11, must not be used to prevent attacks.)
By default this is turned off.
enhanced_dad - BOOLEAN
Include a nonce option in the IPv6 neighbor solicitation messages used for
duplicate address detection per RFC7527. A received DAD NS will only signal
a duplicate address if the nonce is different. This avoids any false
detection of duplicates due to loopback of the NS messages that we send.
The nonce option will be sent on an interface unless both of
conf/{all,interface}/enhanced_dad are set to FALSE.
Default: TRUE
icmp/*:
ratelimit - INTEGER
Limit the maximal rates for sending ICMPv6 packets.
0 to disable any limiting,
otherwise the minimal space between responses in milliseconds.
Default: 1000
xfrm6_gc_thresh - INTEGER
The threshold at which we will start garbage collecting for IPv6
destination cache entries. At twice this value the system will
refuse new allocations.
IPv6 Update by:
Pekka Savola [email protected]
YOSHIFUJI Hideaki / USAGI Project [email protected]
/proc/sys/net/bridge/* Variables:
bridge-nf-call-arptables - BOOLEAN
1 : pass bridged ARP traffic to arptables' FORWARD chain.
0 : disable this.
Default: 1
bridge-nf-call-iptables - BOOLEAN
1 : pass bridged IPv4 traffic to iptables' chains.
0 : disable this.
Default: 1
bridge-nf-call-ip6tables - BOOLEAN
1 : pass bridged IPv6 traffic to ip6tables' chains.
0 : disable this.
Default: 1
bridge-nf-filter-vlan-tagged - BOOLEAN
1 : pass bridged vlan-tagged ARP/IP/IPv6 traffic to {arp,ip,ip6}tables.
0 : disable this.
Default: 0
bridge-nf-filter-pppoe-tagged - BOOLEAN
1 : pass bridged pppoe-tagged IP/IPv6 traffic to {ip,ip6}tables.
0 : disable this.
Default: 0
bridge-nf-pass-vlan-input-dev - BOOLEAN
1: if bridge-nf-filter-vlan-tagged is enabled, try to find a vlan
interface on the bridge and set the netfilter input device to the vlan.
This allows use of e.g. "iptables -i br0.1" and makes the REDIRECT
target work with vlan-on-top-of-bridge interfaces. When no matching
vlan interface is found, or this switch is off, the input device is
set to the bridge interface.
0: disable bridge netfilter vlan interface lookup.
Default: 0
proc/sys/net/sctp/* Variables:
addip_enable - BOOLEAN
Enable or disable extension of Dynamic Address Reconfiguration
(ADD-IP) functionality specified in RFC5061. This extension provides
the ability to dynamically add and remove new addresses for the SCTP
associations.
1: Enable extension.
0: Disable extension.
Default: 0
pf_enable - INTEGER
Enable or disable pf (pf is short for potentially failed) state. A value
of pf_retrans > path_max_retrans also disables pf state. That is, one of
both pf_enable and pf_retrans > path_max_retrans can disable pf state.
Since pf_retrans and path_max_retrans can be changed by userspace
application, sometimes user expects to disable pf state by the value of
pf_retrans > path_max_retrans, but occasionally the value of pf_retrans
or path_max_retrans is changed by the user application, this pf state is
enabled. As such, it is necessary to add this to dynamically enable
and disable pf state. See:
https://datatracker.ietf.org/doc/draft-ietf-tsvwg-sctp-failover for
details.
1: Enable pf.
0: Disable pf.
Default: 1
addip_noauth_enable - BOOLEAN
Dynamic Address Reconfiguration (ADD-IP) requires the use of
authentication to protect the operations of adding or removing new
addresses. This requirement is mandated so that unauthorized hosts
would not be able to hijack associations. However, older
implementations may not have implemented this requirement while
allowing the ADD-IP extension. For reasons of interoperability,
we provide this variable to control the enforcement of the
authentication requirement.
1: Allow ADD-IP extension to be used without authentication. This
should only be set in a closed environment for interoperability
with older implementations.
0: Enforce the authentication requirement
Default: 0
auth_enable - BOOLEAN
Enable or disable Authenticated Chunks extension. This extension
provides the ability to send and receive authenticated chunks and is
required for secure operation of Dynamic Address Reconfiguration
(ADD-IP) extension.
1: Enable this extension.
0: Disable this extension.
Default: 0
prsctp_enable - BOOLEAN
Enable or disable the Partial Reliability extension (RFC3758) which
is used to notify peers that a given DATA should no longer be expected.
1: Enable extension
0: Disable
Default: 1
max_burst - INTEGER
The limit of the number of new packets that can be initially sent. It
controls how bursty the generated traffic can be.
Default: 4
association_max_retrans - INTEGER
Set the maximum number for retransmissions that an association can
attempt deciding that the remote end is unreachable. If this value
is exceeded, the association is terminated.
Default: 10
max_init_retransmits - INTEGER
The maximum number of retransmissions of INIT and COOKIE-ECHO chunks
that an association will attempt before declaring the destination
unreachable and terminating.
Default: 8
path_max_retrans - INTEGER
The maximum number of retransmissions that will be attempted on a given
path. Once this threshold is exceeded, the path is considered
unreachable, and new traffic will use a different path when the
association is multihomed.
Default: 5
pf_retrans - INTEGER
The number of retransmissions that will be attempted on a given path
before traffic is redirected to an alternate transport (should one
exist). Note this is distinct from path_max_retrans, as a path that
passes the pf_retrans threshold can still be used. Its only
deprioritized when a transmission path is selected by the stack. This
setting is primarily used to enable fast failover mechanisms without
having to reduce path_max_retrans to a very low value. See:
http://www.ietf.org/id/draft-nishida-tsvwg-sctp-failover-05.txt
for details. Note also that a value of pf_retrans > path_max_retrans
disables this feature. Since both pf_retrans and path_max_retrans can
be changed by userspace application, a variable pf_enable is used to
disable pf state.
Default: 0
rto_initial - INTEGER
The initial round trip timeout value in milliseconds that will be used
in calculating round trip times. This is the initial time interval
for retransmissions.
Default: 3000
rto_max - INTEGER
The maximum value (in milliseconds) of the round trip timeout. This
is the largest time interval that can elapse between retransmissions.
Default: 60000
rto_min - INTEGER
The minimum value (in milliseconds) of the round trip timeout. This
is the smallest time interval the can elapse between retransmissions.
Default: 1000
hb_interval - INTEGER
The interval (in milliseconds) between HEARTBEAT chunks. These chunks
are sent at the specified interval on idle paths to probe the state of
a given path between 2 associations.
Default: 30000
sack_timeout - INTEGER
The amount of time (in milliseconds) that the implementation will wait
to send a SACK.
Default: 200
valid_cookie_life - INTEGER
The default lifetime of the SCTP cookie (in milliseconds). The cookie
is used during association establishment.
Default: 60000
cookie_preserve_enable - BOOLEAN
Enable or disable the ability to extend the lifetime of the SCTP cookie
that is used during the establishment phase of SCTP association
1: Enable cookie lifetime extension.
0: Disable
Default: 1
cookie_hmac_alg - STRING
Select the hmac algorithm used when generating the cookie value sent by
a listening sctp socket to a connecting client in the INIT-ACK chunk.
Valid values are:
* md5
* sha1
* none
Ability to assign md5 or sha1 as the selected alg is predicated on the
configuration of those algorithms at build time (CONFIG_CRYPTO_MD5 and
CONFIG_CRYPTO_SHA1).
Default: Dependent on configuration. MD5 if available, else SHA1 if
available, else none.
rcvbuf_policy - INTEGER
Determines if the receive buffer is attributed to the socket or to
association. SCTP supports the capability to create multiple
associations on a single socket. When using this capability, it is
possible that a single stalled association that's buffering a lot
of data may block other associations from delivering their data by
consuming all of the receive buffer space. To work around this,
the rcvbuf_policy could be set to attribute the receiver buffer space
to each association instead of the socket. This prevents the described
blocking.
1: rcvbuf space is per association
0: rcvbuf space is per socket
Default: 0
sndbuf_policy - INTEGER
Similar to rcvbuf_policy above, this applies to send buffer space.
1: Send buffer is tracked per association
0: Send buffer is tracked per socket.
Default: 0
sctp_mem - vector of 3 INTEGERs: min, pressure, max
Number of pages allowed for queueing by all SCTP sockets.
min: Below this number of pages SCTP is not bothered about its
memory appetite. When amount of memory allocated by SCTP exceeds
this number, SCTP starts to moderate memory usage.
pressure: This value was introduced to follow format of tcp_mem.
max: Number of pages allowed for queueing by all SCTP sockets.
Default is calculated at boot time from amount of available memory.
sctp_rmem - vector of 3 INTEGERs: min, default, max
Only the first value ("min") is used, "default" and "max" are
ignored.
min: Minimal size of receive buffer used by SCTP socket.
It is guaranteed to each SCTP socket (but not association) even
under moderate memory pressure.
Default: 1 page
sctp_wmem - vector of 3 INTEGERs: min, default, max
Currently this tunable has no effect.
addr_scope_policy - INTEGER
Control IPv4 address scoping - draft-stewart-tsvwg-sctp-ipv4-00
0 - Disable IPv4 address scoping
1 - Enable IPv4 address scoping
2 - Follow draft but allow IPv4 private addresses
3 - Follow draft but allow IPv4 link local addresses
Default: 1
/proc/sys/net/core/*
Please see: Documentation/sysctl/net.txt for descriptions of these entries.
/proc/sys/net/unix/*
max_dgram_qlen - INTEGER
The maximum length of dgram socket receive queue
Default: 10
UNDOCUMENTED:
/proc/sys/net/irda/*
fast_poll_increase FIXME
warn_noreply_time FIXME
discovery_slots FIXME
slot_timeout FIXME
max_baud_rate FIXME
discovery_timeout FIXME
lap_keepalive_time FIXME
max_noreply_time FIXME
max_tx_data_size FIXME
max_tx_window FIXME
min_tx_turn_time FIXME