华为eNSP综合实验

实验目标

企业内网全网互通，R3配置DHCP服务为Vlan10和vlan20的域内的PC分配IP地址外网vm虚拟机测试server1的web业务测试。

实验步骤

1.SW2和SW3是普通的二层交换机，划分VLAN 配置Access 和Trunk口
2.SW1是三层交换机，划分VLAN 配置Access 和Trunk口 还想逻辑接口IP地址、DHCP中继和路由信息
3.R3配置DHCP服务为Vlan10和VLAN20的域内的PC分配IP地址
4.Server1架设WEB服务让外网VM2虚拟机能访问server1服务
5.AR1路由器配NAT技术（Easy IP ）让VLAN10和VLAN20 的PC能访问运营商PC5 还需将server1的WWW服务映射出去.
6.R2配置回城路由Ip地址信息，以及单臂路由
7.SW4普通的二层交换机，划分VLAN 配置Access 和Trunk口
8.VM2云绑定VM2 ，开虚拟机测试server1的web业务测试

SW2二层配置信息

[SW1]vlan batch 10 20											#划分VLAN 10 20
[SW1]int g0/0/1													#进入G0/0/1接口
[SW1-GigabitEthernet0/0/1]port link-type trunk 					#接口是trunk链路
[SW1-GigabitEthernet0/0/1]port trunk allow-pass vlan all		#方通全VLAN
[SW1-GigabitEthernet0/0/1]int g0/0/2
[SW1-GigabitEthernet0/0/2]port link-type trunk 
[SW1-GigabitEthernet0/0/2]port trunk allow-pass vlan 10 20
[SW1-GigabitEthernet0/0/2]int e0/0/1
[SW1-Ethernet0/0/1]port link-type access 						#接口是access标志
[SW1-Ethernet0/0/1]port default vlan 10							#划分到vlan10
[SW1-Ethernet0/0/1]int e0/0/2
[SW1-Ethernet0/0/2]port link-type access
[SW1-Ethernet0/0/2]port default vlan 20

SW3二层配置信息

[SW2]vlan batch 10 20
[SW2]int g0/0/1
[SW2-GigabitEthernet0/0/1]port link-type trunk
[SW2-GigabitEthernet0/0/1]port trunk allow-pass vlan all	
[SW2-GigabitEthernet0/0/1]int e0/0/1
[SW2-Ethernet0/0/1]port link-type access
[SW2-Ethernet0/0/1]port default vlan 10
[SW2-Ethernet0/0/1]int e0/0/2
[SW2-Ethernet0/0/2]port link-type access
[SW2-Ethernet0/0/2]port default vlan 20

SW1三层配置信息

[RSW1]vlan batch 10 20 30 40 50
[RSW1]int g0/0/1
[RSW1-GigabitEthernet0/0/1]port link-type access 
[RSW1-GigabitEthernet0/0/1]port default vlan 30
[RSW1-GigabitEthernet0/0/1]int g0/0/2
[RSW1-GigabitEthernet0/0/2]port link-type trunk
[RSW1-GigabitEthernet0/0/2]port trunk allow-pass vlan 10 20
[RSW1-GigabitEthernet0/0/2]int g0/0/3
[RSW1-GigabitEthernet0/0/3]port link-type access 
[RSW1-GigabitEthernet0/0/3]port default vlan 40
[RSW1-GigabitEthernet0/0/3]int g0/0/4
[RSW1-GigabitEthernet0/0/4]port link-type access 
[RSW1-GigabitEthernet0/0/4]port default vlan 50
[RSW1]int Vlanif 10												#进入vlanif10逻辑接口
[RSW1-Vlanif10]ip address 192.168.10.1 24						#逻辑接口IP地址
[RSW1-Vlanif10]int vlanif 20
[RSW1-Vlanif20]ip address 192.168.20.1 24
[RSW1-Vlanif20]int vlanif 30
[RSW1-Vlanif30]ip address 192.168.30.1 24
[RSW1-Vlanif30]int vlanif 40
[RSW1-Vlanif40]ip address 11.0.0.2 24
[RSW1-Vlanif40]int vlanif 50
[RSW1-Vlanif50]ip address 13.0.0.1 24
[RSW1]dhcp enable 												#开启DHCP服务
[RSW1]int Vlanif 10
[RSW1-Vlanif10]dhcp select relay								#选择中继接口
[RSW1-Vlanif10]dhcp relay server-ip 13.0.0.3					#中继接口IP
[RSW1-Vlanif10]int vlanif 20
[RSW1-Vlanif20]dhcp select relay
[RSW1-Vlanif20]dhcp relay server-ip 13.0.0.3
[RSW1]ip route-static 0.0.0.0 0.0.0.0 11.0.0.1					#上跳默认路由

R3路由器配置信息

[R3]dhcp enable 											
[R3]int g0/0/0
[R3-GigabitEthernet0/0/0]ip add 13.0.0.3 24						#物理接口ip地址
[R3]ip pool DHCPvlanif10										#命名地址池
[R3-ip-pool-DHCPvlanif10]network 192.168.10.0 mask 24			#地址池网段子网掩码
[R3-ip-pool-DHCPvlanif10]gateway-list 192.168.10.1				#指定网关
[R3-ip-pool-DHCPvlanif10]dns-list 8.8.8.8 2.2.2.2				#DNS服务器
[R3]ip pool DHCPvlanif20
[R3-ip-pool-DHCPvlanif20]network 192.168.20.0 mask 24
[R3-ip-pool-DHCPvlanif20]gateway-list 192.168.20.1
[R3-ip-pool-DHCPvlanif20]dns-list 8.8.8.8 2.2.2.2
[R3-ip-pool-DHCPvlanif10]int g0/0/0
[R3-GigabitEthernet0/0/0]dhcp select global						#从g0/0/0接口去找服务
[R3]ip route-static 0.0.0.0 0.0.0.0 13.0.0.1					#上跳默认路由

AR1路由器配置信息

[R1]int g0/0/1
[R1-GigabitEthernet0/0/1]ip add 11.0.0.1 24
[R1-GigabitEthernet0/0/1]int g0/0/0
[R1-GigabitEthernet0/0/0]ip add 12.0.0.1 24
[R1]acl 3000													 #高级acl编号3000
[R1-acl-adv-3000]rule permit ip source 192.168.10.0 0.0.0.255	 #允许此网段的数据包通过
[R1-acl-adv-3000]rule permit ip source 192.168.20.0 0.0.0.255
[R1-acl-adv-3000]int g0/0/0
[R1-GigabitEthernet0/0/0]nat outbound 3000						 #地址池从G0/0/0口转换成外网
[R1-GigabitEthernet0/0/0]nat server protocol tcp global 202.0.0.2 www inside 192.168.30.10 www
#把server1服务器映射出并转换成公网地址让外网能访问进来
[R1]ip route-static 0.0.0.0 0.0.0.0 12.0.0.2					 #默认路由
[R1]ip route-static 192.168.10.1 24 11.0.0.2					 #静态路由
[R1]ip route-static 192.168.20.1 24 11.0.0.2
[R1]ip route-static 192.168.30.1 24 11.0.0.2

R2路由器配置信息

[R2]int g0/0/0
[R2-GigabitEthernet0/0/0]ip address 12.0.0.2 24
[R2]int g0/0/3.100												#进入子接口
[R2-GigabitEthernet0/0/3.100]dot1q termination vid 100			#封装dot1q协议改子接口对应vlan100
[R2-GigabitEthernet0/0/3.100]ip address 192.168.100.1 24		#子接口IP 子网
[R2-GigabitEthernet0/0/3.100]arp broadcast enable 				#开启arp广播
[R2-GigabitEthernet0/0/3.100]int g0/0/3.200
[R2-GigabitEthernet0/0/3.200]dot1q termination vid 200
[R2-GigabitEthernet0/0/3.200]ip address 192.168.110.1 24
[R2-GigabitEthernet0/0/3.200]arp broadcast enable 
[R2]ip route-static 202.0.0.2 32 12.0.0.1		

SW4二层交换机配置信息

[SW3]int g0/0/1
[SW3-GigabitEthernet0/0/1]port link-type trunk 
[SW3-GigabitEthernet0/0/1]port trunk allow-pass vlan 100 200
[SW3]int e0/0/1
[SW3-Ethernet0/0/1]port link-type access
[SW3-Ethernet0/0/1]port default vlan 100
[SW3]int e0/0/2
[SW3-Ethernet0/0/2]port link-type access
[SW3-Ethernet0/0/2]port default vlan 200

总结

1.配置静态默认路由要仔细
2.映射IP地址
3.VM虚拟机网卡配置确认

如果有错误的地方，欢迎评论，我加以改正。