CentOS Environmentfile变量

Using environment variables in systemd units

Environment directive

systemd has an Environment directive which sets environment variables for executed processes. It takes a space-separated list of variable assignments. This option may be specified more than once in which case all listed variables will be set. If the same variable is set twice, the later setting will override the earlier setting. If the empty string is assigned to this option, the list of environment variables is reset, all prior assignments have no effect. Environments directives are used in built-in Container Linux systemd units, for example in etcd2 and flannel.

With the example below, you can configure your etcd2 daemon to use encryption. Just create /etc/systemd/system/etcd2.service.d/30-certificates.conf drop-in for etcd2.service:

[Service]
# Client Env Vars
Environment=ETCD_CA_FILE=/path/to/CA.pem
Environment=ETCD_CERT_FILE=/path/to/server.crt
Environment=ETCD_KEY_FILE=/path/to/server.key
# Peer Env Vars
Environment=ETCD_PEER_CA_FILE=/path/to/CA.pem
Environment=ETCD_PEER_CERT_FILE=/path/to/peers.crt
Environment=ETCD_PEER_KEY_FILE=/path/to/peers.key

Then run sudo systemctl daemon-reload and sudo systemctl restart etcd2.service to apply new environments to etcd2 daemon. You can read more about etcd2 certificates here.

EnvironmentFile directive

EnvironmentFile similar to Environment directive but reads the environment variables from a text file. The text file should contain new-line-separated variable assignments.

For example, in Container Linux, the coreos-metadata.service service creates /run/metadata/coreos. This environment file can be included by other services in order to inject dynamic configuration. Here's an example of the environment file when run on DigitalOcean (the IP addresses have been removed):

COREOS_DIGITALOCEAN_IPV4_ANCHOR_0=X.X.X.X
COREOS_DIGITALOCEAN_IPV4_PRIVATE_0=X.X.X.X
COREOS_DIGITALOCEAN_HOSTNAME=test.example.com
COREOS_DIGITALOCEAN_IPV4_PUBLIC_0=X.X.X.X
COREOS_DIGITALOCEAN_IPV6_PUBLIC_0=X:X:X:X:X:X:X:X

This environment file can then be sourced and its variables used. Here is an example drop-in for etcd-member.service which starts coreos-metadata.service and then uses the generated results:

[Unit]
Requires=coreos-metadata.service
After=coreos-metadata.service

[Service]
EnvironmentFile=/run/metadata/coreos
ExecStart=
ExecStart=/usr/bin/etcd2 \
  --advertise-client-urls=http://${COREOS_DIGITALOCEAN_IPV4_PUBLIC_0}:2379 \
  --initial-advertise-peer-urls=http://${COREOS_DIGITALOCEAN_IPV4_PRIVATE_0}:2380 \
  --listen-client-urls=http://0.0.0.0:2379 \
  --listen-peer-urls=http://${COREOS_DIGITALOCEAN_IPV4_PRIVATE_0}:2380 \
  --initial-cluster=%m=http://${COREOS_DIGITALOCEAN_IPV4_PRIVATE_0}:2380

Other examples

Use host IP addresses and EnvironmentFile

You can also write your host IP addresses into /etc/network-environment file using this utility. Then you can run your Docker containers following way:

[Unit]
Description=Nginx service
Requires=etcd2.service
After=etcd2.service
[Service]
# Get network environmental variables
EnvironmentFile=/etc/network-environment
ExecStartPre=-/usr/bin/docker kill nginx
ExecStartPre=-/usr/bin/docker rm nginx
ExecStartPre=/usr/bin/docker pull nginx
ExecStartPre=/usr/bin/etcdctl set /services/nginx '{"host": "%H", "ipv4_addr": ${DEFAULT_IPV4}, "port": 80}'
ExecStart=/usr/bin/docker run --rm --name nginx -p ${DEFAULT_IPV4}:80:80 nginx
ExecStop=/usr/bin/docker stop nginx
ExecStopPost=/usr/bin/etcdctl rm /services/nginx

This unit file will run nginx Docker container and bind it to specific IP address and port.

System wide environment variables

You can define system wide environment variables using a Container Linux Config as explained below:

• Container Linux Config
• Ignition Config

This is the human-readable config file. This should not be immediately passed to Container Linux.  Learn more.

# This config is meant to be consumed by the config transpiler, which will
# generate the corresponding Ignition config. Do not pass this config directly
# to instances of Container Linux.

storage:
  files:
    - path: /etc/systemd/system.conf.d/10-default-env.conf
      filesystem: root
      mode: 0644
      contents:
        inline: |
          [Manager]
          DefaultEnvironment=HTTP_PROXY=http://192.168.0.1:3128
    - path: /etc/profile.env
      filesystem: root
      mode: 0644
      contents:
        inline: |
          export HTTP_PROXY=http://192.168.0.1:3128

Where:

• /etc/systemd/system.conf.d/10-default-env.conf config file will set default environment variables for all systemd units.
• /etc/profile.env will set environment variables for all users logged in Container Linux.

etcd2.service unit advanced example

A complete example of combining environment variables and systemd drop-ins to reconfigure an existing machine running etcd.