PowerDesigner16配置显示注释comment配置方法

无论15还是16.视图中都没有直接设置显示属性字段注释的配置，因此需要通过间接的方式显示注释，操作的流程图如下

原始样式

显示操作

调出执行命令的接口

执行夏利命令

从name替换comment

Option   Explicit
ValidationMode   =   True
InteractiveMode   =   im_Batch

Dim   mdl   '   the   current   model

'   get   the   current   active   model
Set   mdl   =   ActiveModel
If   (mdl   Is   Nothing)   Then
      MsgBox   "There   is   no   current   Model "
ElseIf   Not   mdl.IsKindOf(PdPDM.cls_Model)   Then
      MsgBox   "The   current   model   is   not   an   Physical   Data   model. "
Else
      ProcessFolder   mdl
End   If

'   This   routine   copy   name   into   comment   for   each   table,   each   column   and   each   view
'   of   the   current   folder
Private   sub   ProcessFolder(folder)
      Dim   Tab   'running     table
      for   each   Tab   in   folder.tables
            if   not   tab.isShortcut   then
                  tab.comment   =   tab.name
                  Dim   col   '   running   column
                  for   each   col   in   tab.columns
                        col.comment=   col.name
                  next
            end   if
      next

      Dim   view   'running   view
      for   each   view   in   folder.Views
            if   not   view.isShortcut   then
                  view.comment   =   view.name
            end   if
      next

      '   go   into   the   sub-packages
      Dim   f   '   running   folder
      For   Each   f   In   folder.Packages
            if   not   f.IsShortcut   then
                  ProcessFolder   f
            end   if
      Next
end   sub

Option   Explicit 
ValidationMode   =   True 
InteractiveMode   =   im_Batch

Dim   mdl   '   the   current   model

'   get   the   current   active   model 
Set   mdl   =   ActiveModel 
If   (mdl   Is   Nothing)   Then 
      MsgBox   "There   is   no   current   Model " 
ElseIf   Not   mdl.IsKindOf(PdPDM.cls_Model)   Then 
      MsgBox   "The   current   model   is   not   an   Physical   Data   model. " 
Else 
      ProcessFolder   mdl 
End   If

'   This   routine   copy   name   into   comment   for   each   table,   each   column   and   each   view 
'   of   the   current   folder 
Private   sub   ProcessFolder(folder) 
      Dim   Tab   'running     table 
      for   each   Tab   in   folder.tables 
            if   not   tab.isShortcut   then 
                  tab.comment   =   tab.name 
                  Dim   col   '   running   column 
                  for   each   col   in   tab.columns 
                        col.comment=   col.name 
                  next 
            end   if 
      next

      Dim   view   'running   view 
      for   each   view   in   folder.Views 
            if   not   view.isShortcut   then 
                  view.comment   =   view.name 
            end   if 
      next

      '   go   into   the   sub-packages 
      Dim   f   '   running   folder 
      For   Each   f   In   folder.Packages 
            if   not   f.IsShortcut   then 
                  ProcessFolder   f 
            end   if 
      Next 
end   sub

从comment替换name

Option   Explicit
ValidationMode   =   True
InteractiveMode   =   im_Batch

Dim   mdl   '   the   current   model

'   get   the   current   active   model
Set   mdl   =   ActiveModel
If   (mdl   Is   Nothing)   Then
      MsgBox   "There   is   no   current   Model "
ElseIf   Not   mdl.IsKindOf(PdPDM.cls_Model)   Then
      MsgBox   "The   current   model   is   not   an   Physical   Data   model. "
Else
      ProcessFolder   mdl
End   If

Private   sub   ProcessFolder(folder)
On Error Resume Next
      Dim   Tab   'running     table
      for   each   Tab   in   folder.tables
            if   not   tab.isShortcut   then
                  tab.name   =   tab.comment
                  Dim   col   '   running   column
                  for   each   col   in   tab.columns
                  if col.comment="" then
                  else
                        col.name=   col.comment
                  end if
                  next
            end   if
      next

      Dim   view   'running   view
      for   each   view   in   folder.Views
            if   not   view.isShortcut   then
                  view.name   =   view.comment
            end   if
      next

      '   go   into   the   sub-packages
      Dim   f   '   running   folder
      For   Each   f   In   folder.Packages
            if   not   f.IsShortcut   then
                  ProcessFolder   f
            end   if
      Next
end   sub

Option   Explicit 
ValidationMode   =   True 
InteractiveMode   =   im_Batch

Dim   mdl   '   the   current   model

'   get   the   current   active   model 
Set   mdl   =   ActiveModel 
If   (mdl   Is   Nothing)   Then 
      MsgBox   "There   is   no   current   Model " 
ElseIf   Not   mdl.IsKindOf(PdPDM.cls_Model)   Then 
      MsgBox   "The   current   model   is   not   an   Physical   Data   model. " 
Else 
      ProcessFolder   mdl 
End   If

Private   sub   ProcessFolder(folder) 
On Error Resume Next
      Dim   Tab   'running     table 
      for   each   Tab   in   folder.tables 
            if   not   tab.isShortcut   then 
                  tab.name   =   tab.comment
                  Dim   col   '   running   column 
                  for   each   col   in   tab.columns 
                  if col.comment="" then
                  else
                        col.name=   col.comment 
                  end if
                  next 
            end   if 
      next

      Dim   view   'running   view 
      for   each   view   in   folder.Views 
            if   not   view.isShortcut   then 
                  view.name   =   view.comment 
            end   if 
      next

      '   go   into   the   sub-packages 
      Dim   f   '   running   folder 
      For   Each   f   In   folder.Packages 
            if   not   f.IsShortcut   then 
                  ProcessFolder   f 
            end   if 
      Next 
end   sub

最终效果图如下

可以看到图1中的id列已被中文注释替换。