Smart210使用superboot刷机

友善之臂提供的superboot除了像u-boot一样启动内核文件系统外,还可以当作刷机工具。友善在smart210 用户手册里面提供的方法是使用USB配合minitool软件在线刷机,这也是友善推荐的方法。

但是这里使用SD卡烧写。

 

方法如下:

一. 烧写superboot到SD卡

1. 以管理员权限打开SD-Flasher.exe

2. 在SD卡里面新建images目录,拷贝如下内容:

 

其中zImage就是编译得到的kernel, rootfs_qtopia_qt4xx是文件系统,Superboot210.bin是u-boot

 

3. 修改FriendlyARM.ini配置文件如下

#This line cannot be removed. by FriendlyARM(www.arm9.net)

CheckOneButton=No
Action = Install
OS =Linux

LCD-Mode = No
LCD-Type = S70

LowFormat = Yes
VerifyNandWrite = No
CheckCRC32=No

StatusType = Beeper | LED

################### Linux ####################
Linux-BootLoader = Superboot210.bin
Linux-Kernel = zImage
Linux-CommandLine = root=/dev/mtdblock4 rootfstype=yaffs2 console=ttySAC0,115200 init=/linuxrc
Linux-RootFs-InstallImage = rootfs_qtopia_qt4.img

二. 使用SD卡刷机

 

  1. 硬件准备

    第一步制作的SD卡,插入主板, 启动方式设为SD启动, 接入串口转USB到COM0, 打开teraterm软件

  2. 上电

    串口输出:

Booting from SD
NAND Low-level formating...
NAND Low-level formatted...

Superboot-210
Ver: 1.28a(20180409a)
CPU: S5PV210 1GHz
RAM: 512MB
NAND: 1GB(SLC) ID:ECD35195
Touch Device: no 1-wire
LCD Type: S70(Manu)

Installing OS 'LINUX'
Installing bootloader...
file: /images/Superboot210.bin: 528 KB(540672 Byte)
Installing bootloader succeed
Installing kernel...
file: /images/zImage: 4 MB(4840652 Byte)
Installing kernel succeed
Installing yaffs2-image...
file: /images/rootfs_qtopia_qt4.img: 316 MB(331864896 Byte)
Installing yaffs2-image succeed
OS 'LINUX' Installed

注意上面步骤最后烧写rootfs比较耗时,完成后,蜂鸣器会响一下,而且出现流水灯。

3. 然后断电, 把启动方式设置位NAND启动,拔掉SD卡

Booting from NAND
Load Kernel...
Uncompressing Linux... done, booting the kernel.
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.0.8-FriendlyARM (root@jensen) (gcc version 4.5.1 (ctng-1.8.1-FA) ) #1 PREEMPT Wed Apr 11 14:16:31 HKT 2018
[    0.000000] CPU: ARMv7 Processor [412fc082] revision 2 (ARMv7), cr=10c53c7f
[    0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: MINI210
[    0.000000] MINI210: S70 selected
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] CPU S5PV210/S5PC110 (id 0x43110220)
[    0.000000] S3C24XX Clocks, Copyright 2004 Simtec Electronics
[    0.000000] S5PV210: PLL settings, A=1000000000, M=667000000, E=80000000 V=54000000
[    0.000000] S5PV210: ARMCLK=1000000000, HCLKM=200000000, HCLKD=166750000
[    0.000000] HCLKP=133400000, PCLKM=100000000, PCLKD=83375000, PCLKP=66700000
[    0.000000] sclk_dmc: source is sclk_a2m (0), rate is 200000000
[    0.000000] sclk_onenand: source is hclk_dsys (1), rate is 166750000
[    0.000000] uclk1: source is mout_mpll (6), rate is 66700000
[    0.000000] uclk1: source is mout_mpll (6), rate is 66700000
[    0.000000] uclk1: source is mout_mpll (6), rate is 66700000
[    0.000000] uclk1: source is mout_mpll (6), rate is 66700000
[    0.000000] sclk_mixer: source is sclk_dac (0), rate is 54000000
[    0.000000] sclk_fimc: source is ext_xtal (0), rate is 24000000
[    0.000000] sclk_fimc: source is ext_xtal (0), rate is 24000000
[    0.000000] sclk_fimc: source is ext_xtal (0), rate is 24000000
[    0.000000] sclk_cam0: source is ext_xtal (0), rate is 24000000
[    0.000000] sclk_cam1: source is ext_xtal (0), rate is 24000000
[    0.000000] sclk_fimd: source is ext_xtal (0), rate is 24000000
[    0.000000] sclk_mmc: source is mout_epll (7), rate is 80000000
[    0.000000] sclk_mmc: source is mout_epll (7), rate is 80000000
[    0.000000] sclk_mmc: source is mout_epll (7), rate is 80000000
[    0.000000] sclk_mmc: source is mout_epll (7), rate is 80000000
[    0.000000] sclk_mfc: source is sclk_a2m (0), rate is 200000000
[    0.000000] sclk_g2d: source is sclk_a2m (0), rate is 200000000
[    0.000000] sclk_g3d: source is sclk_a2m (0), rate is 200000000
[    0.000000] sclk_csis: source is ext_xtal (0), rate is 24000000
[    0.000000] sclk_spi: source is ext_xtal (0), rate is 24000000
[    0.000000] sclk_spi: source is ext_xtal (0), rate is 24000000
[    0.000000] sclk_pwi: source is ext_xtal (0), rate is 24000000
[    0.000000] sclk_pwm: source is ext_xtal (0), rate is 24000000
[    0.000000] s5p: 36864 kbytes system memory reserved for mfc at 0x2dc00000, 0-bank base(0x2dc00000)
[    0.000000] s5p: 36864 kbytes system memory reserved for mfc at 0x3dbf6000, 1-bank base(0x3dbf6000)
[    0.000000] s5p: 6144 kbytes system memory reserved for fimc0 at 0x3d5f6000, 1-bank base(0x3d5f6000)
[    0.000000] s5p: 16 kbytes system memory reserved for fimc1 at 0x3d5f2000, 1-bank base(0x3d5f2000)
[    0.000000] s5p: 6144 kbytes system memory reserved for fimc2 at 0x3cff2000, 1-bank base(0x3cff2000)
[    0.000000] s5p: 8192 kbytes system memory reserved for jpeg at 0x2d400000, 0-bank base(0x2d400000)
[    0.000000] s5p: 13060 kbytes system memory reserved for fimd at 0x3c331000, 1-bank base(0x3c331000)
[    0.000000] s5p: 8192 kbytes system memory reserved for g2d at 0x2cc00000, 0-bank base(0x2cc00000)
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 101179
[    0.000000] Kernel command line: root=/dev/mtdblock4 rootfstype=yaffs2 console=ttySAC0,115200 init=/linuxrc lcd=S70
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 204MB 195MB 0MB = 399MB total
[    0.000000] Memory: 394528k/510004k available, 14284k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     DMA     : 0xff000000 - 0xffe00000   (  14 MB)
[    0.000000]     vmalloc : 0xe0800000 - 0xfd000000   ( 456 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xe0000000   ( 512 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .init : 0xc0008000 - 0xc0174000   (1456 kB)
[    0.000000]       .text : 0xc0174000 - 0xc08da258   (7577 kB)
[    0.000000]       .data : 0xc08dc000 - 0xc0934580   ( 354 kB)
[    0.000000]        .bss : 0xc09345a4 - 0xc0979b20   ( 278 kB)
[    0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:393
[    0.000000] VIC @fd000000: id 0x00041192, vendor 0x41
[    0.000000] VIC @fd010000: id 0x00041192, vendor 0x41
[    0.000000] VIC @fd020000: id 0x00041192, vendor 0x41
[    0.000000] VIC @fd030000: id 0x00041192, vendor 0x41
[    0.000000] sched_clock: 32 bits at 33MHz, resolution 29ns, wraps every 128784ms
[    0.000000] Console: colour dummy device 80x30
[    0.000000] console [ttySAC0] enabled
[    0.431691] Calibrating delay loop... 997.78 BogoMIPS (lpj=2494464)
[    0.464998] pid_max: default: 32768 minimum: 301
[    0.465157] Mount-cache hash table entries: 512
[    0.465489] Initializing cgroup subsys debug
[    0.465531] Initializing cgroup subsys cpuacct
[    0.465577] Initializing cgroup subsys freezer
[    0.467598] CPU: Testing write buffer coherency: ok
[    0.475196] print_constraints: dummy:
[    0.476282] NET: Registered protocol family 16
[    0.485751] S3C Power Management, Copyright 2004 Simtec Electronics
[    0.492267] fimd at 0x3c331000
[    0.492349] hsmmc0: sclk_mmc: source is mout_mpll, rate is 47642857
[    0.496134] hsmmc1: sclk_mmc: source is mout_mpll, rate is 47642857
[    0.502426] hsmmc2: sclk_mmc: source is mout_mpll, rate is 47642857
[    0.508595] hsmmc3: sclk_mmc: source is mout_mpll, rate is 47642857
[    0.515626] S5PV210: Initializing architecture
[    0.519868] s3c-adc s5pv210-adc: attached adc driver
[    0.524346] s3c24xx-pwm s3c24xx-pwm.0: tin at 33350000, tdiv at 33350000, tin=divclk, base 0
[    0.532976] print_constraints: pd_tv_supply: 5000 mV normal
[    0.538379] print_constraints: pd_lcd_supply: 5000 mV normal
[    0.544105] print_constraints: pd_g3d_supply: 5000 mV normal
[    0.549805] print_constraints: pd_mfc_supply: 5000 mV normal
[    0.555533] print_constraints: pd_audio_supply: 5000 mV normal
[    0.592433] bio: create slab  at 0
[    0.593388] SCSI subsystem initialized
[    0.595243] usbcore: registered new interface driver usbfs
[    0.595537] usbcore: registered new interface driver hub
[    0.595729] usbcore: registered new device driver usb
[    0.596278] s3c-i2c s3c2440-i2c.0: slave address 0x10
[    0.598690] s3c-i2c s3c2440-i2c.0: bus frequency set to 378 KHz
[    0.605439] s3c-i2c s3c2440-i2c.0: i2c-0: S3C I2C adapter
[    0.610022] s3c-i2c s3c2440-i2c.1: slave address 0x10
[    0.615006] s3c-i2c s3c2440-i2c.1: bus frequency set to 65 KHz
[    0.621049] s3c-i2c s3c2440-i2c.1: i2c-1: S3C I2C adapter
[    0.626218] s3c-i2c s3c2440-i2c.2: slave address 0x10
[    0.631204] s3c-i2c s3c2440-i2c.2: bus frequency set to 378 KHz
[    0.637826] s3c-i2c s3c2440-i2c.2: i2c-2: S3C I2C adapter
[    0.643012] Advanced Linux Sound Architecture Driver Version 1.0.24.
[    0.649348] Bluetooth: Core ver 2.16
[    0.652482] NET: Registered protocol family 31
[    0.656795] Bluetooth: HCI device and connection manager initialized
[    0.663096] Bluetooth: HCI socket layer initialized
[    0.667938] Bluetooth: L2CAP socket layer initialized
[    0.672962] Bluetooth: SCO socket layer initialized
[    0.678056] Switching to clocksource s5p_clocksource_timer
[    0.684996] Switched to NOHz mode on CPU #0
[    0.697091] NET: Registered protocol family 2
[    0.697279] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.699667] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    0.706166] TCP bind hash table entries: 16384 (order: 6, 327680 bytes)
[    0.712776] TCP: Hash tables configured (established 16384 bind 16384)
[    0.718985] TCP reno registered
[    0.722089] UDP hash table entries: 256 (order: 1, 12288 bytes)
[    0.728006] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes)
[    0.734527] NET: Registered protocol family 1
[    0.738890] RPC: Registered named UNIX socket transport module.
[    0.744582] RPC: Registered udp transport module.
[    0.749221] RPC: Registered tcp transport module.
[    0.753900] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.769645] NetWinder Floating Point Emulator V0.97 (double precision)
[    0.769780] PMU: registered new PMU device of type 0
[    0.772058] cpuidle: phy_regs_save:0x3bf3f000
[    0.776287] Loaded driver for PL330 DMAC-0 s3c-pl330
[    0.781056]  DBUFF-64x8bytes Num_Chans-8 Num_Peri-2 Num_Events-32
[    0.787166] Loaded driver for PL330 DMAC-1 s3c-pl330
[    0.792035]  DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[    0.798179] Loaded driver for PL330 DMAC-2 s3c-pl330
[    0.803038]  DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[    0.817215] ashmem: initialized
[    0.831073] NTFS driver 2.1.30 [Flags: R/W].
[    0.831568] ROMFS MTD (C) 2007 Red Hat, Inc.
[    0.831836] msgmni has been set to 770
[    0.832817] io scheduler noop registered
[    0.832854] io scheduler deadline registered
[    0.832940] io scheduler cfq registered (default)
[    0.837322] start plist test
[    0.845118] end plist test
[    0.845890] s3cfb s3cfb: win 2: pmem_start=0x3c796000
[    0.847827] s3cfb s3cfb: [fb2] dma: 0x3c796000, cpu: 0xe1000000, size: 0x0085c000
[    0.866828] Console: switching to colour frame buffer device 100x30
[    0.871909] FIMD src sclk = 166750000
[    0.871979] s3cfb s3cfb: registered successfully
[    0.872020] Start display and show logo
[    0.878948] s5pv210-uart.0: ttySAC0 at MMIO 0xe2900000 (irq = 16) is a S3C6400/10
[    0.883572] s5pv210-uart.1: ttySAC1 at MMIO 0xe2900400 (irq = 20) is a S3C6400/10
[    0.898345] s5pv210-uart.2: ttySAC2 at MMIO 0xe2900800 (irq = 24) is a S3C6400/10
[    0.908344] s5pv210-uart.3: ttySAC3 at MMIO 0xe2900c00 (irq = 28) is a S3C6400/10
[    0.918796] leds     initialized
[    0.918963] buttons  initialized
[    0.919147] pwm      initialized
[    0.919341] mini210-adc      initialized
[    0.919633] backlight        initialized
[    0.920473] PA FB = 0x3C796000, bits per pixel = 32
[    0.923783] screen width=800 height=480 va=0xdc796000 pa=0x3c796000
[    0.930044] xres_virtual = 800, yres_virtual = 1440, xoffset = 0, yoffset = 0
[    0.937095] fb_size=8765440
[    0.939880] Back frameBuffer[0].VAddr=dc90d000 PAddr=3c90d000 size=1536000
[    0.946715] Back frameBuffer[1].VAddr=dca84000 PAddr=3ca84000 size=1536000
[    0.953567] Video Y Buffer[0].VAddr=dcbfb000 PAddr=3cbfb000 size=921600
[    0.960146] Video Y Buffer[1].VAddr=dccdc000 PAddr=3ccdc000 size=921600
[    0.966730] Video Y Buffer[2].VAddr=dcdbd000 PAddr=3cdbd000 size=921600
[    0.973316] Video UV Buffer[0].VAddr=dce9e000 PAddr=3ce9e000 size=462848
[    0.979991] Video UV Buffer[1].VAddr=dcf0f000 PAddr=3cf0f000 size=462848
[    0.986661] Video UV Buffer[2].VAddr=dcf80000 PAddr=3cf80000 size=462848
[    0.999723] brd: module loaded
[    1.002959] loop: module loaded
[    1.004381] S3C NAND Driver, (c) 2008 Samsung Electronics
[    1.108627] S3C NAND Driver is using hardware ECC.
[    1.108705] NAND device: Manufacturer ID: 0xec, Chip ID: 0xd3 (Samsung NAND 1GiB 3,3V 8-bit)
[    1.108779] NAND subpage size: 2048 bytes
[    1.108817] Creating 5 MTD partitions on "s5pv210-nand":
[    1.108868] 0x0000000c0000-0x000000100000 : "misc"
[    1.114645] 0x000000100000-0x000000600000 : "recovery"
[    1.121274] 0x000000600000-0x000000b00000 : "kernel"
[    1.126227] 0x000000b00000-0x000000e00000 : "ramdisk"
[    1.130530] 0x000000e00000-0x000040000000 : "system"
[    1.490125] PPP generic driver version 2.4.2
[    1.490447] PPP Deflate Compression module registered
[    1.490493] PPP BSD Compression module registered
[    1.490960] PPP MPPE Compression module registered
[    1.491004] NET: Registered protocol family 24
[    1.492463] tun: Universal TUN/TAP device driver, 1.6
[    1.496071] tun: (C) 1999-2004 Max Krasnyansky 
[    1.502445] dm9000 Ethernet Driver, V1.31
[    1.507396] eth0: dm9000a at e0838000,e083c00c IRQ 39 MAC: 08:90:00:a0:02:10 (platform data)
[    1.514883] usbcore: registered new interface driver dm9620
[    1.520273] sdhci: Secure Digital Host Controller Interface driver
[    1.526311] sdhci: Copyright(c) Pierre Ossman
[    1.530679] s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133400000 Hz)
[    1.537220] s3c-sdhci s3c-sdhci.0: clock source 2: sclk_mmc (47642857 Hz)
[    1.544017] mmc0: no vmmc regulator found
[    1.548224] mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA
[    1.555037] s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133400000 Hz)
[    1.561567] s3c-sdhci s3c-sdhci.1: clock source 2: sclk_mmc (47642857 Hz)
[    1.570355] mmc1: no vmmc regulator found
[    1.572611] mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA
[    1.579380] s3c-sdhci s3c-sdhci.2: clock source 0: hsmmc (133400000 Hz)
[    1.585936] s3c-sdhci s3c-sdhci.2: clock source 2: sclk_mmc (47642857 Hz)
[    1.592720] mmc2: no vmmc regulator found
[    1.599985] mmc2: SDHCI controller on samsung-hsmmc [s3c-sdhci.2] using ADMA
[    1.603738] s3c-sdhci s3c-sdhci.3: clock source 0: hsmmc (133400000 Hz)
[    1.610274] s3c-sdhci s3c-sdhci.3: clock source 2: sclk_mmc (47642857 Hz)
[    1.617052] mmc3: no vmmc regulator found
[    1.621276] mmc3: SDHCI controller on samsung-hsmmc [s3c-sdhci.3] using ADMA
[    1.628162] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.634752] s5p-ehci s5p-ehci: S5P EHCI Host Controller
[    1.640802] s5p-ehci s5p-ehci: new USB bus registered, assigned bus number 1
[    1.648858] s5p-ehci s5p-ehci: irq 87, io mem 0xec200000
[    1.658341] s5p-ehci s5p-ehci: USB 0.0 started, EHCI 1.00
[    1.658961] hub 1-0:1.0: USB hub found
[    1.661124] hub 1-0:1.0: 1 port detected
[    1.665471] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.671314] s5p-ohci s5p-ohci: EXYNOS OHCI Host Controller
[    1.676671] s5p-ohci s5p-ohci: new USB bus registered, assigned bus number 2
[    1.683691] s5p-ohci s5p-ohci: irq 87, io mem 0xec300000
[    1.747855] hub 2-0:1.0: USB hub found
[    1.747906] hub 2-0:1.0: 1 port detected
[    1.748673] usbcore: registered new interface driver usbserial
[    1.748848] USB Serial support registered for generic
[    1.749039] usbcore: registered new interface driver usbserial_generic
[    1.750551] usbserial: USB Serial Driver core
[    1.755039] USB Serial support registered for aircable
[    1.760174] usbcore: registered new interface driver aircable
[    1.765902] USB Serial support registered for ark3116
[    1.770923] usbcore: registered new interface driver ark3116
[    1.776427] ark3116:v0.6:USB ARK3116 serial/IrDA driver
[    1.781695] USB Serial support registered for Belkin / Peracom / GoHubs USB Serial Adapter
[    1.789970] usbcore: registered new interface driver belkin
[    1.795404] belkin_sa: v1.3:USB Belkin Serial converter driver
[    1.801292] USB Serial support registered for ch341-uart
[    1.806599] usbcore: registered new interface driver ch341
[    1.812037] USB Serial support registered for cp210x
[    1.817021] usbcore: registered new interface driver cp210x
[    1.822444] cp210x: v0.09:Silicon Labs CP210x RS232 serial adaptor driver
[    1.829284] USB Serial support registered for Reiner SCT Cyberjack USB card reader
[    1.836871] usbcore: registered new interface driver cyberjack
[    1.842549] cyberjack: v1.01 Matthias Bruestle
[    1.846984] cyberjack: REINER SCT cyberJack pinpad/e-com USB Chipcard Reader Driver
[    1.854676] USB Serial support registered for DeLorme Earthmate USB
[    1.860958] USB Serial support registered for HID->COM RS232 Adapter
[    1.867309] USB Serial support registered for Nokia CA-42 V2 Adapter
[    1.873616] usbcore: registered new interface driver cypress
[    1.879128] cypress_m8: v1.10:Cypress USB to Serial Driver
[    1.884669] USB Serial support registered for Digi 2 port USB adapter
[    1.891098] USB Serial support registered for Digi 4 port USB adapter
[    1.897531] usbcore: registered new interface driver digi_acceleport
[    1.904763] mmc0: new high speed SDHC card at address 1234
[    1.909434] digi_acceleport: v1.80.1.2:Digi AccelePort USB-2/USB-4 Serial Converter driver
[    1.917409] mmcblk0: mmc0:1234 SA16G 14.6 GiB
[    1.922656] USB Serial support registered for Edgeport 2 port adapter
[    1.928337]  mmcblk0: p1
[    1.931357] USB Serial support registered for Edgeport 4 port adapter
[    1.937268] USB Serial support registered for Edgeport 8 port adapter
[    1.945698] USB Serial support registered for EPiC device
[    1.949089] usbcore: registered new interface driver io_edgeport
[    1.954938] io_edgeport: v2.7:Edgeport USB Serial Driver
[    1.963444] USB Serial support registered for Edgeport TI 1 port adapter
[    1.966971] USB Serial support registered for Edgeport TI 2 port adapter
[    1.973560] usb 1-1: new high speed USB device number 2 using s5p-ehci
[    1.982180] usbcore: registered new interface driver io_ti
[    1.985511] io_ti: v0.7mode043006:Edgeport USB Serial Driver
[    1.991258] USB Serial support registered for empeg
[    1.999291] usbcore: registered new interface driver empeg
[    2.001422] empeg: v1.3:USB Empeg Mark I/II Driver
[    2.006336] USB Serial support registered for FTDI USB Serial Device
[    2.012758] usbcore: registered new interface driver ftdi_sio
[    2.020301] ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
[    2.024154] USB Serial support registered for funsoft
[    2.029224] usbcore: registered new interface driver funsoft
[    2.037944] USB Serial support registered for Garmin GPS usb/tty
[    2.040832] usbcore: registered new interface driver garmin_gps
[    2.046613] garmin_gps: v0.36:garmin gps driver
[    2.053406] USB Serial support registered for hp4X
[    2.055975] usbcore: registered new interface driver hp4X
[    2.061272] hp4x: v1.00:HP4x (48/49) Generic Serial driver
[    2.069943] USB Serial support registered for PocketPC PDA
[    2.072328] usbcore: registered new interface driver ipaq
[    2.077544] ipaq: v1.0:USB PocketPC PDA driver
[    2.082050] USB Serial support registered for IPWireless converter
[    2.090256] usbcore: registered new interface driver ipwtty
[    2.093659] ipw: v0.4:IPWireless tty driver
[    2.097887] USB Serial support registered for IR Dongle
[    2.103142] usbcore: registered new interface driver ir-usb
[    2.108606] ir_usb: v0.5:USB IR Dongle driver
[    2.113010] USB Serial support registered for iuu_phoenix
[    2.119438] usbcore: registered new interface driver iuu_phoenix
[    2.126262] iuu_phoenix: v0.12:Infinity USB Unlimited Phoenix driver
[    2.130732] USB Serial support registered for Keyspan PDA
[    2.136445] USB Serial support registered for Keyspan PDA - (prerenumeration)
[    2.143274] hub 1-1:1.0: USB hub found
[    2.146928] hub 1-1:1.0: 4 ports detected
[    2.150803] USB Serial support registered for Xircom / Entregra PGS - (prerenumeration)
[    2.159002] usbcore: registered new interface driver keyspan_pda
[    2.164766] keyspan_pda: v1.1:USB Keyspan PDA Converter driver
[    2.170689] USB Serial support registered for KL5KUSB105D / PalmConnect
[    2.177294] usbcore: registered new interface driver kl5kusb105d
[    2.183106] kl5kusb105: v0.4:KLSI KL5KUSB105 chipset USB->Serial Converter driver
[    2.192882] USB Serial support registered for KOBIL USB smart card terminal
[    2.197604] usbcore: registered new interface driver kobil
[    2.202948] kobil_sct: 21/05/2004:KOBIL USB Smart Card Terminal Driver (experimental)
[    2.210841] USB Serial support registered for MCT U232
[    2.215988] usbcore: registered new interface driver mct_u232
[    2.222585] mct_u232: z2.1:Magic Control Technology USB-RS232 converter driver
[    2.230859] USB Serial support registered for Moschip 2 port adapter
[    2.235102] mos7720: 2.1:Moschip USB Serial Driver
[    2.239967] usbcore: registered new interface driver moschip7720
[    2.245949] USB Serial support registered for Moschip 7840/7820 USB Serial Driver
[    2.253316] mos7840: 1.3.2:Moschip 7840/7820 USB Serial Driver
[    2.259232] usbcore: registered new interface driver mos7840
[    2.264839] USB Serial support registered for moto-modem
[    2.270143] usbcore: registered new interface driver moto-modem
[    2.276025] USB Serial support registered for navman
[    2.280980] usbcore: registered new interface driver navman
[    2.286512] USB Serial support registered for ZyXEL - omni.net lcd plus usb
[    2.293514] usbcore: registered new interface driver omninet
[    2.301020] omninet: v1.1:USB ZyXEL omni.net LCD PLUS Driver
[    2.304718] USB Serial support registered for opticon
[    2.309734] usbcore: registered new interface driver opticon
[    2.315375] USB Serial support registered for GSM modem (1-port)
[    2.321449] usbcore: registered new interface driver option
[    2.327790] option: v0.7.2:USB Driver for GSM modems
[    2.333824] USB Serial support registered for oti6858
[    2.336857] usbcore: registered new interface driver oti6858
[    2.342482] USB Serial support registered for pl2303
[    2.347451] usbcore: registered new interface driver pl2303
[    2.352865] pl2303: Prolific PL2303 USB to serial adaptor driver
[    2.358940] USB Serial support registered for qcaux
[    2.363867] usbcore: registered new interface driver qcaux
[    2.369258] USB Serial support registered for Qualcomm USB modem
[    2.375277] usbcore: registered new interface driver qcserial
[    2.380863] safe_serial: v0.1:USB Safe Encapsulated Serial
[    2.386410] USB Serial support registered for safe_serial
[    2.391798] usbcore: registered new interface driver safe_serial
[    2.397756] USB Serial support registered for siemens_mpi
[    2.405164] usbcore: registered new interface driver siemens_mpi
[    2.409003] Driver for Siemens USB/MPI adapter
[    2.413410] Version 0.1 09/26/2005 Thomas [email protected] http://libnodave.sf.net
[    2.421141] USB Serial support registered for Sierra USB modem
[    2.426999] usbcore: registered new interface driver sierra
[    2.433438] sierra: v.1.7.16:USB Driver for Sierra Wireless USB modems
[    2.440996] USB Serial support registered for SPCP8x5
[    2.444064] usbcore: registered new interface driver spcp8x5
[    2.449578] spcp8x5: v0.10:SPCP8x5 USB to serial adaptor driver
[    2.455554] USB Serial support registered for Quatech SSU-100 USB to Serial Driver
[    2.463145] usbcore: registered new interface driver ssu100
[    2.468676] ssu100: v0.1:Quatech SSU-100 USB to Serial Driver
[    2.474360] USB Serial support registered for symbol
[    2.479339] usbcore: registered new interface driver symbol
[    2.484865] USB Serial support registered for TI USB 3410 1 port adapter
[    2.491541] USB Serial support registered for TI USB 5052 2 port adapter
[    2.498252] usbcore: registered new interface driver ti_usb_3410_5052
[    2.504509] ti_usb_3410_5052: v0.10:TI USB 3410/5052 Serial Driver
[    2.512750] USB Serial support registered for Handspring Visor / Palm OS
[    2.517433] USB Serial support registered for Sony Clie 3.5
[    2.522972] USB Serial support registered for Sony Clie 5.0
[    2.528557] usbcore: registered new interface driver visor
[    2.533898] visor: USB HandSpring Visor / Palm OS driver
[    2.540268] USB Serial support registered for Connect Tech - WhiteHEAT - (prerenumeration)
[    2.549524] USB Serial support registered for Connect Tech - WhiteHEAT
[    2.554033] usbcore: registered new interface driver whiteheat
[    2.559712] whiteheat: v2.0:USB ConnectTech WhiteHEAT driver
[    2.565426] USB Serial support registered for vivopay-serial
[    2.571210] usbcore: registered new interface driver vivopay-serial
[    2.577222] vivopay_serial: v1.0:ViVOpay USB Serial Driver
[    2.582766] USB Serial support registered for zio
[    2.587472] usbcore: registered new interface driver zio
[    2.592646] Initializing USB Mass Storage driver...
[    2.597656] usbcore: registered new interface driver usb-storage
[    2.603484] USB Mass Storage support registered.
[    2.608211] s3c-udc : S3C HS USB Device Controller Driver, (c) 2008-2009 Samsung Electronics
[    2.608218] s3c-udc : version 15 March 2009 (DMA Mode)
[    2.625861] android_usb gadget: Mass Storage Function, version: 2009/09/11
[    2.628413] android_usb gadget: Number of LUNs=1
[    2.632979]  lun0: LUN: removable file: (no medium)
[    2.638225] android_usb gadget: android_usb ready
[    2.659441] Registered gadget driver 'android_usb'
[    2.659773] mousedev: PS/2 mouse device common for all mice
[    2.660119] touchscreen-1wire        initialized
[    2.660297] backlight-1wire  initialized
[    2.660739] onewire: REQ 0x60: i2c write error -6
[    2.665378] PWM clock = 66700000
[    2.670664] TCNT_FOR_SAMPLE_BIT = 3472, TCFG1 = 00000003
[    2.674278] input: fa_ts_input as /devices/virtual/input/input0
[    2.680195] ts-if    initialized
[    2.682785] <<-GTP-INFO->> GTP driver installing...
[    2.688045] S3C24XX RTC, (c) 2004,2006 Simtec Electronics
[    2.693042] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
[    2.699412] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
[    2.705903] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
[    2.709643] using rtc device, s3c, for alarms
[    2.713470] s3c-rtc s3c64xx-rtc: rtc core: registered s3c as rtc0
[    2.719793] i2c /dev entries driver
[    2.723800] Linux video capture interface: v2.00
[    2.727831] mfc_init: <6>S5PC110 MFC Driver, (c) 2009 Samsung Electronics
[    2.727837]
[    2.738862] S3C JPEG Driver, (c) 2007 Samsung Electronics
[    2.741302] JPEG driver for S5PV210
[    2.745379] i2c i2c-1: attached s5p_ddc into i2c adapter successfully
[    2.753384] S5PC11X HPD Driver, (c) 2010 Samsung Electronics
[    2.757151] S5PC11X CEC Driver, (c) 2010 Samsung Electronics
[    2.763478] usbcore: registered new interface driver uvcvideo
[    2.768209] USB Video Class driver (v1.1.0)
[    2.821295] input: mma7660 as /devices/platform/s3c2440-i2c.0/i2c-0/0-004c/input/input1
[    2.821585] mma7660 0-004c: MMA7660 device is probed successfully.
[    2.821761] i2c-core: driver [mma7660] using legacy suspend method
[    2.821813] i2c-core: driver [mma7660] using legacy resume method
[    2.825426] MMA7660 sensor driver registered.
[    2.829744] S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
[    2.835856] s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
[    2.844205] device-mapper: uevent: version 1.0.3
[    2.848253] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: [email protected]
[    2.856311] Bluetooth: HCI UART driver ver 2.2
[    2.860731] Bluetooth: HCI H4 protocol initialized
[    2.865437] Bluetooth: HCILL protocol initialized
[    2.870358] cpuidle: using governor ladder
[    2.874408] cpuidle: using governor menu
[    2.884978] usbcore: registered new interface driver usbhid
[    2.885030] usbhid: USB HID core driver
[    2.888988] ALSA device list:
[    2.890373]   No soundcards found.
[    2.893795] oprofile: hardware counters not available
[    2.898812] oprofile: using timer interrupt.
[    2.903138] GACT probability NOT on
[    2.906525] Mirror/redirect action on
[    2.910149] u32 classifier
[    2.912820]     Actions configured
[    2.916214] Netfilter messages via NETLINK v0.30.
[    2.920954] nf_conntrack version 0.5.0 (6164 buckets, 24656 max)
[    2.927726] ctnetlink v0.93: registering with nfnetlink.
[    2.932233] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[    2.939100] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[    2.945251] xt_time: kernel timezone is -0000
[    2.950781] ip_tables: (C) 2000-2006 Netfilter Core Team
[    2.954691] arp_tables: (C) 2002 David S. Miller
[    2.959174] TCP cubic registered
[    2.963260] NET: Registered protocol family 10
[    2.971490] Mobile IPv6
[    2.971541] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    2.974764] IPv6 over IPv4 tunneling driver
[    2.983163] NET: Registered protocol family 17
[    2.983231] NET: Registered protocol family 15
[    2.987630] Bluetooth: RFCOMM TTY layer initialized
[    2.992439] Bluetooth: RFCOMM socket layer initialized
[    2.997502] Bluetooth: RFCOMM ver 1.11
[    3.001226] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    3.006515] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    3.012635] NET: Registered protocol family 35
[    3.016951] Registering the dns_resolver key type
[    3.021547] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2
[    3.029128] ThumbEE CPU extension supported.
[    3.033540] s5pv210_cpufreq_init: S5PV210 cpu-freq driver
[    3.039350] regulator_init_complete: pd_mfc_supply: disabling
[    3.044502] regulator_init_complete: pd_tv_supply: disabling
[    3.050167] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
[    3.055569] s3c-rtc s3c64xx-rtc: hctosys: unable to read the hardware clock
[    3.063987] FIMC0 registered successfully
[    3.067790] FIMC1 registered successfully
[    3.071852] FIMC2 registered successfully
[    3.074579] S5PC1XX TVOUT Driver, (c) 2009 Samsung Electronics
[    3.080794] s5p-tvout s5p-tvout: hpd status is cable removed
[    3.092427] Freeing init memory: 1456K
[    3.099863] yaffs: dev is 32505860 name is "mtdblock4" rw
[    3.099918] yaffs: passed flags ""
[   19.296124] FAT-fs (mmcblk0p1): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[   19.296134]
[   19.689260] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
hwclock: RTC_RD_TIME: Invalid argument
[01/Jan/1970:00:00:21 +0000] boa: server version Boa/0.94.13
[01/Jan/1970:00:00:21 +0000] boa: server built Dec 30 2010 at 11:18:35.
[01/Jan/1970:00:00:21 +0000] boa: starting server pid=1110, port 80

[   23.812313] FriendlyARM http://www.arm9.net
[   23.920996] asoc: wm8960-hifi <-> samsung-i2s.0 mapping ok

[   24.724449]
[   24.724456] rtw driver version=v3.3.2_3192.20120103
[   24.724515] ##########rtw_suspend_lock_init ###########
[   24.728578] usbcore: registered new interface driver rtl8192cu
[   24.743761] Compat-wireless backport release: compat-wireless-2012-05-04
[   24.743824] Backport based on linux-next.git next-20120510
[   24.763170] cfg80211: Calling CRDA to update world regulatory domain
[   24.817790] usbcore: registered new interface driver ath9k_htc
[   24.848298] usbcore: registered new interface driver rt73usb
[   24.876131] usbcore: registered new interface driver rt2800usb
[   24.896535] usbcore: registered new interface driver zd1211rw
[   24.918581] libertas_sdio: Libertas SDIO driver
[   24.918631] libertas_sdio: Copyright Pierre Ossman
Try to bring eth0 interface up......[   24.968454] dm9000 dm9000: eth0: link down
[   24.968736] ADDRCONF(NETDEV_UP): eth0: link is not ready
Done

Please press Enter to activate this console.

 

你可能感兴趣的:(smart210)