ZCU106 Board Interface Test (BIT)

参考：

参考xpt491、xpt495、xpt497，WIN11、vivado2019.2

收到了xilinx官方ZCU106，进行Board Interface Test遇到的问题

---

遇到问题

1）、安装 Si Labs CP210x USB UART Drivers 不能自动安装，通过手动安装

1. Using Windows File Explorer, locate the driver folder
   (that you previously unzipped)
2. Right click on the **silabser.inf** file and select Install
3. Follow the instructions;

2）、点击 BoardUI 没反应，点击 layout 取消 hide right pane，查看logging，有如下信息，发现是端口问题，COM8 和 COM9 关闭即可解决（我把蓝牙关了）

Exception in thread Thread-9:
Traceback (most recent call last):
  File "threading.py", line 801, in __bootstrap_inner
  File "testthread.py", line 85, in run
  File "testthread.py", line 152, in runbutton
  File "testthread.py", line 520, in sysc
UnicodeEncodeError: 'ascii' codec can't encode characters in position 0-9: ordinal not in range(128)
或者
Exception in thread Thread-2:
Traceback (most recent call last):
  File "threading.py", line 801, in __bootstrap_inner
  File "testthread.py", line 85, in run
  File "testthread.py", line 206, in runbutton
  File "testthread.py", line 785, in shell
UnicodeEncodeError: 'ascii' codec can't encode characters in position 0-9: ordinal not in range(128)

最后只有下图所示端口就可以了

3）、SYS_CTLR RESTORE，提示 Invalid input for COM port，CP201x

then run "firmware\Firmware_flash_gui.bat" COM6 ZCU106_PROD C 1280937F020 000A35038013 prod 2.6 "4ATF51264HZ-2G6E1" "L:\[.*?\.0\].*?\[.*?Quad.*?USB to UART .*?\]" "L:\[.*?\.1\].*?\[.*?Quad.*?USB to UART .*?\]" "L:\[.*?\.2\].*?\[.*?Quad.*?USB to UART .*?\]" "" "" "" "" "" "" "" "1"
Error: Invalid input for COM port
Usage: MSP_BSL_Flasher.exe -c <COM port name> -f <File to be sent> -b <baud rate>-t <receiver timeout time> -r <maximum number of retries> -v <to enable verification> -p <to show progress bar>
Found fail condition:
(.*)Error(.*)
Could not find pass condition:
(.*)File\s+sent\s+successfully
Could not find pass condition:
(.*)System\s+controller\s+programmed\s+successfully

打开文件.\zcu106_bit\BoardUI\tests\ZCU106_PROD\firmware\Firmware_flash_gui.bat，我的驱动是2108，将"CP201x" 修改为 “Silicon Labs Quad CP2108 USB to UART Bridge: Interface 0” -v -p

:: Note: change the "CP201x" to match what your driver names the ports, e.g. CP2105, CP2108, or CP210x.
@ECHO OFF
cd firmware
MSP_BSL_Flasher.exe -f "MSP_code.txt" -c "Silicon Labs Quad CP2108 USB to UART Bridge: Interface 0" -v -p

4）、program QSPI 失败，Flash Programming Unsuccessful，J56 连接 3-4 而不是 1-2. (ZCU106)

Downloading FSBL...
Running FSBL...
Finished running FSBL.
Problem in running uboot
Flash programming initialization failed.
ERROR: [Labtools 27-3161] Flash Programming Unsuccessful

5）、修改完Firmware_flash_gui.bat，SYS_CTLR RESTORE测试还是失败，提示 Error: BSL Flashing Failed, 还未解决

6）、PING 失败，还未解决

autonegotiation complete 
link speed for phy address 12: 1000
DHCP Timeout
Configuring default IP of 192.168.1.10
Board IP: 192.168.1.10
Netmask : 255.255.255.0
Gateway : 192.168.1.1
TCP echo server started @ port 7
Returned from UART: u'autonegotiation complete \r\nlink speed for phy address 12: 1000\r\nDHCP Timeout\r\nConfiguring default IP of 192.168.1.10\r\nBoard IP: 192.168.1.10\n\rNetmask : 255.255.255.0\n\rGateway : 192.168.1.1\n\rTCP echo server started @ port 7\n\r'
Starting step cmd
==========
To run this command manually open a shell in "C:\zcu106_bit\BoardUI\tests\ZCU106_PROD"
then run "ping\ping.bat" COM3 ZCU106_PROD C 1280937F020 000A35038013 prod 2.6 "L:\[.*?\.0\].*?\[.*?Quad.*?USB to UART .*?\]" "L:\[.*?\.1\].*?\[.*?Quad.*?USB to UART .*?\]" "L:\[.*?\.2\].*?\[.*?Quad.*?USB to UART .*?\]" "" "" "" "" "" "" "" "1"

 File "site-packages\wx\core.py", line 3163, in <lambda>
UnicodeDecodeError
 1:
92'utf8' codec can't decode byte 0xda in position 0: unexpected end of data
.168.1.10 : =32 <1ms TTL=255

Traceback (most recent call last):
  File "site-packages\wx\core.py", line 3163, in <lambda>
UnicodeDecodeError

---