Pandorabox的cubietruck启动

U-Boot SPL 2014.04 (Oct 31 2014 - 17:02:41)

Board: Cubietruck

DRAM: 2048 MiB

CPU: 960000000Hz, AXI/AHB/APB: 3/2/2

spl: not an uImage at 1600

U-Boot 2014.04 (Oct 31 2014 - 17:02:41) Allwinner Technology

CPU:   Allwinner A20 (SUN7I)

Board: Cubietruck

I2C:   ready

DRAM:  2 GiB

MMC:   SUNXI SD/MMC: 0

*** Warning - bad CRC, using default environment

In:    serial

Out:   serial

Err:   serial

Net:   dwmac.1c50000

Hit any key to stop autoboot:  0 

reading uEnv.txt

240 bytes read in 16 ms (14.6 KiB/s)

Loaded environment from uEnv.txt

Running uenvcmd ...

reading uImage

2540384 bytes read in 293 ms (8.3 MiB/s)

reading dtb

23026 bytes read in 29 ms (775.4 KiB/s)

## Booting kernel from Legacy Image at 46000000 ...

   Image Name:   ARM OpenWrt Linux-3.14.18

   Image Type:   ARM Linux Kernel Image (uncompressed)

   Data Size:    2540320 Bytes = 2.4 MiB

   Load Address: 40008000

   Entry Point:  40008000

   Verifying Checksum ... S倐率2

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0

[    0.000000] Linux version 3.14.18 (hades@PandoraBox-Server) (gcc version 4.8.3 (PandoraBox/Linaro GCC 4.8-2014.04 svn-r173) ) #5 SMP PREEMPT Tue Nov 4 14:08:28 CST 2014

[    0.000000] CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=10c5387d

[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache

[    0.000000] Machine model: Cubietech Cubietruck

[    0.000000] Memory policy: Data cache writealloc

[    0.000000] PERCPU: Embedded 7 pages/cpu @ee7d6000 s7104 r8192 d13376 u32768

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 522768

[    0.000000] Kernel command line: console=ttyS0,115200 earlyprintk rootwait root=/dev/mmcblk0p2

[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)

[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)

[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)

[    0.000000] Memory: 2074212K/2097152K available (3603K kernel code, 161K rwdata, 1016K rodata, 182K init, 602K bss, 22940K reserved, 1318912K highmem)

[    0.000000] Virtual kernel memory layout:

[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)

[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)

[    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)

[    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)

[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)

[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)

[    0.000000]       .text : 0xc0008000 - 0xc048af04   (4620 kB)

[    0.000000]       .init : 0xc048b000 - 0xc04b8bc0   ( 183 kB)

[    0.000000]       .data : 0xc04ba000 - 0xc04e2660   ( 162 kB)

[    0.000000]        .bss : 0xc04e2660 - 0xc057921c   ( 603 kB)

[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1

[    0.000000] Preemptible hierarchical RCU implementation.

[    0.000000]  RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.

[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2

[    0.000000] NR_IRQS:16 nr_irqs:16 16

[    0.000023] sched_clock: 32 bits at 24MHz, resolution 41ns墮

[    0.137688] usbcore: registered new interface driver hub

[    0.137821] usbcore: registered new device driver usb

[    0.137933] pps_core: LinuxPPS API ver. 1 registered

[    0.137941] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>

[    0.137966] PTP clock support registered

[    0.138837] Switched to clocksource timer

[    0.140352] Clockevents: could not switch to one-shot mode: dummy_timer is not functional.

[    0.140371] Could not switch to high resolution mode on CPU 0

[    0.145793] NET: Registered protocol family 2

[    0.146788] TCP established hash table entries: 8192 (order: 3, 32768 bytes)

[    0.146877] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)

[    0.146998] TCP: Hash tables configured (established 8192 bind 8192)

[    0.147074] TCP: reno registered

[    0.147095] UDP hash table entries: 512 (order: 2, 16384 bytes)

[    0.147150] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)

[    0.147466] NET: Registered protocol family 1

[    0.148773] futex hash table entries: 512 (order: 3, 32768 bytes)

[    0.148875] audit: initializing netlink subsys (disabled)

[    0.148941] audit: type=2000 audit(0.130:1): initialized

[    0.149514] bounce pool size: 64 pages

[    0.157330] VFS: Disk quotas dquot_6.5.2

[    0.157669] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)

[    0.159574] squashfs: version 4.0 (2009/01/31) Phillip Lougher

[    0.159587] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.

[    0.160522] msgmni has been set to 1475

[    0.162407] io scheduler noop registered

[    0.162425] io scheduler deadline registered

[    0.162470] io scheduler cfq registered (default)

[    0.162744] platform 1c13400.phy: Driver sun4i-usb-phy requests probe deferral

[    0.164994] sunxi-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver

[    0.206567] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled

[    0.228851] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 33, base_baud = 1500000) is a U6_16550A

[    0.809757] console [ttyS0] enabled

[    0.834185] 1c28800.serial: ttyS1 at MMIO 0x1c28800 (irq = 35, base_baud = 1500000) is a U6_16550A

[    0.844075] platform 1c18000.sata: Driver ahci-sunxi requests probe deferral

[    0.852799] stmmaceth 1c50000.ethernet: no regulator found

[    0.858340] stmmaceth 1c50000.ethernet: no reset control found

[    0.864216]  Ring mode enabled

[    0.867271]  No HW DMA feature register supported

[    0.871805]  Normal descriptors

[    0.875128]  TX Checksum insertion supported

[    0.883567] libphy: stmmac: probed

[    0.886981] eth0: PHY ID 001cc915 at 0 IRQ 0 (stmmac-0:00) active

[    0.893145] eth0: PHY ID 001cc915 at 1 IRQ 0 (stmmac-0:01)

[    0.898741] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

[    0.905303] ehci-platform: EHCI generic platform driver

[    0.910744] platform 1c14000.usb: Driver ehci-platform requests probe deferral

[    0.918044] platform 1c1c000.usb: Driver ehci-platform requests probe deferral

[    0.925491] usbcore: registered new interface driver usb-storage

[    0.931839] mousedev: PS/2 mouse device common for all mice

[    0.939064] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)

[    0.947905] sunxi-mmc 1c0f000.mmc: Got CD GPIO #225.

[    0.953150] sunxi-mmc 1c0f000.mmc: base:0xf00f4000 irq:64

[    0.959036] platform 1c12000.mmc: Driver sunxi-mmc requests probe deferral

[    0.967189] sunxi-ss 1c15000.crypto-engine: Die ID 0

[    0.973724] TCP: cubic registered

[    0.977045] Initializing XFRM netlink socket

[    0.981426] NET: Registered protocol family 17

[    0.985969] 8021q: 802.1Q VLAN Support v1.8

[    0.990246] Registering SWP/SWPB emulation handler

[    0.995492] registered taskstats version 1

[    0.999632] regulator-dummy: disabling

[    1.003968] ahci-5v: 5000 mV 

[    1.007374] usb1-vbus: 5000 mV 

[    1.010944] usb2-vbus: 5000 mV 

[    1.014402] vmmc3: 3300 mV 

[    1.080366] ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP_PMP

[    1.087853] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1

[    1.093776] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode

[    1.102757] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc 

[    1.113715] scsi0 : ahci_platform

[    1.117374] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88

[    1.125684] ehci-platform 1c14000.usb: EHCI Host Controller

[    1.131445] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1

[    1.139291] ehci-platform 1c14000.usb: irq 71, io mem 0x01c14000

[    1.160353] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00

[    1.166635] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002

[    1.174469] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1

[    1.181720] usb usb1: Product: EHCI Host Controller

[    1.186621] usb usb1: Manufacturer: Linux 3.14.18 ehci_hcd

[    1.192130] usb usb1: SerialNumber: 1c14000.usb

[    1.197207] hub 1-0:1.0: USB hub found

[    1.201044] hub 1-0:1.0: 1 port detected

[    1.205604] ehci-platform 1c1c000.usb: EHCI Host Controller

[    1.211236] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2

[    1.219071] ehci-platform 1c1c000.usb: irq 72, io mem 0x01c1c000

[    1.240327] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00

[    1.246597] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002

[    1.253399] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1

[    1.260624] usb usb2: Product: EHCI Host Controller

[    1.265498] usb usb2: Manufacturer: Linux 3.14.18 ehci_hcd

[    1.272014] usb usb2: SerialNumber: 1c1c000.usb

[    1.278058] hub 2-0:1.0: USB hub found

[    1.281865] hub 2-0:1.0: 1 port detected

[    1.286993] sunxi-mmc 1c12000.mmc: base:0xf0138000 irq:67

[    1.367527] mmc0: host does not support reading read-only switch. assuming write-enable.

[    1.480338] ata1: SATA link down (SStatus 0 SControl 300)

[    1.500424] Waiting for root device /dev/mmcblk0p2...

[    1.520367] usb 1-1: new high-speed USB device number 2 using ehci-platform

[    1.570326] mmc0: new high speed SDHC card at address 1234

[    1.576432] mmcblk0: mmc0:1234 SA08G 7.21 GiB 

[    1.582465]  mmcblk0: p1 p2

[    1.615844] VFS: Mounted root (squashfs filesystem) readonly on device 179:2.

[    1.623313] Freeing unused kernel memory: 180K (c048b000 - c04b8000)

[    1.745876] usb 1-1: New USB device found, idVendor=048d, idProduct=1167

[    1.786200] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3

[    1.793409] usb 1-1: Product: USB Mass Storage Device

[    1.798458] usb 1-1: Manufacturer: iTE Tech

[    1.802655] usb 1-1: SerialNumber: 0000000922310679

[    1.808352] usb-storage 1-1:1.0: USB Mass Storage device detected

[    1.817778] scsi1 : usb-storage 1-1:1.0

[    1.893542] sunxi-mmc 1c12000.mmc: smc 1 err, cmd 8, RTO !!

[    1.995352] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)

[    2.004764] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)

procd: Console is alive[    2.113986] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)

procd: - watchdog -

[    2.128829] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)

procd: - ubus -

procd: - init -

Please press Enter to activate this console.

BusyBox v1.22.1 (2014-10-31 17:16:37 CST) built-in shell (ash)

Enter 'help' for a list of built-in commands.

  _______________________________________________________________ 

 |    ____                 _                 ____               |

 |   |  _ \ __ _ _ __   __| | ___  _ __ __ _| __ )  _____  __   |

 |   | |_) / _` | '_ \ / _` |/ _ \| '__/ _` |  _ \ / _ \ \/ /   |

 |   |  __/ (_| | | | | (_| | (_) | | | (_| | |_) | (_) >  <    |

 |   |_|   \__,_|_| |_|\__,_|\___/|_|  \__,_|____/ \___/_/\_\   |

 |                                                              |

 |                  PabdoraBox SDK Plantform                    |

 |                    Copyright 2013-2014                       |

 | [    7.368559] NET: Registered protocol family 10

[    7.399681] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)

[    7.422771] ip6_tables: (C) 2000-2006 Netfilter Core Team

[    7.450564] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea

[    7.458490] Backport generated by backports.git backports-20140320-37-g5c33da0

[    7.488367] ip_tables: (C) 2000-2006 Netfilter Core Team

[    7.610091] xt_time: kernel timezone is -0000

[    7.650566] cfg80211: Calling CRDA to update world regulatory domain

[    7.670500] cfg80211: World regulatory domain updated:

[    7.675651] cfg80211:  DFS Master region: unset

[    7.680003] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)

[    7.714448] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)

[    7.729518] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)

[    7.744698] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)

[    7.759926] cfg80211:   (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)

[    7.775340] cfg80211:   (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)

[    7.797717] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)

[    7.820163] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)

[    7.840577] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)

[    7.855160] PPP generic driver version 2.4.2

[    7.870573] NET: Registered protocol family 24

[    7.894962] usbcore: registered new interface driver rtl8192cu

procd: - init complete -