思科AP关联日志

 一次AP和WLC IOS相同时的 关联失败日志，貌似 AP断电后在重新关联都会出现这种问题

 

Xmodem file system is available.
flashfs[0]: 9 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 7524352
flashfs[0]: Bytes available: 8474624
flashfs[0]: flashfs fsck took 33 seconds.
Base ethernet MAC Address: XXXX
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbps, full-duplex
Ethernet port 0 initialized: link is up
button pressed for 1 seconds
process_config_recovery: set IP address and config to default 10.0.0.1
Loading "flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx"...#################################################################################################################################################################################################################################################################

File "flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx" uncompressed and installed, entry point: 0x3000
executing...

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706



Cisco IOS Software, C1240 Software (C1240-RCVK9W8-M), Version 12.4(21a)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 02-Nov-09 18:40 by prod_rel_team


Proceeding with system init

Proceeding to unmask interrupts
Initializing flashfs...

flashfs[1]: 9 files, 3 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 15998976
flashfs[1]: Bytes used: 7524352
flashfs[1]: Bytes available: 8474624
flashfs[1]: flashfs fsck took 4 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
[email protected].

cisco AIR-LAP1242AG-C-K9   (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
Processor board ID FGL1453U071
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 3.0.51.0
1 FastEthernet interface

32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: XXXX
Part Number                          : 73-10256-07
PCA Assembly Number                  : 800-26918-06
PCA Revision Number                  : A0
PCB Serial Number                    : FOC14493BLW
Top Assembly Part Number             : 800-29152-03
Top Assembly Serial Number           : FGL1453U071
Top Revision Number                  : A0
Product/Model Number                 : AIR-LAP1242AG-C-K9
% Please define a domain-name first.


Press RETURN to get started!


*Mar  1 00:00:05.942: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1024 messages)

*Mar  1 00:00:08.018: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar  1 00:00:08.068: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1240 Software (C1240-RCVK9W8-M), Version 12.4(21a)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 02-Nov-09 18:40 by prod_rel_team
*Mar  1 00:00:08.145: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar  1 00:00:08.654: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
*Mar  1 00:00:09.018: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar  1 00:00:16.412: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 172.16.200.43, mask 255.255.255.0, hostname AP

*Mar  1 00:00:33.242: %CAPWAP-3-ERRORLOG: Dropping dtls packet since session is not established.
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar  1 00:00:37.968: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.

Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)
*Mar  1 00:00:46.968: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER

*Mar  1 00:00:55.969: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER
*Mar  1 00:01:05.970: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Mar  8 16:28:08.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.61.100 peer_port: 5246
*Mar  8 16:28:08.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Mar  8 16:28:09.548: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.61.100 peer_port: 5246
*Mar  8 16:28:09.550: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.61.100
*Mar  8 16:28:09.550: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
examining image...
extracting info (295 bytes)
Image info:
    Version Suffix: k9w8-.124-21a.JHB1
    Image Name: c1240-k9w8-mx.124-21a.JHB1
    Version Directory: c1240-k9w8-mx.124-21a.JHB1
    Ios Image Size: 4813312
    Total Image Size: 4813312
    Image Feature: WIRELESS LAN|LWAPP
    Image Family: C1240
    Wireless Switch Management Version: 6.0.199.4
Extracting files... (这个时候失败了）
c1240-k9w8-mx.124-21a.JHB1/ (directory) 0 (bytes)
extracting c1240-k9w8-mx.124-21a.JHB1/c1240-k9w8-mx.124-21a.JHB1 (4543348 bytes)
*Mar  8 16:28:14.549: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.61.100perform archive download capwap:/c1240 tar file
*Mar  8 16:28:14.618: %CAPWAP-5-CHANGED: CAPWAP changed state to IMAGE
*Mar  8 16:29:05.916: %CAPWAP-3-ERRORLOG: Unencrypted non-discovery CAPWAP Control Message from 172.16.61.100
*Mar  8 16:29:05.916: %CAPWAP-3-ERRORLOG: Invalid AC Message Type 34078720.
*Mar  8 16:29:05.916: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar  8 16:29:05.916: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.16.61.100
*Mar  8 16:29:06.241: %CAPWAP-3-ERRORLOG: Unencrypted non-discovery CAPWAP Control Message from 172.16.61.100
*Mar  8 16:29:06.241: %CAPWAP-3-ERRORLOG: Invalid AC Message Type 34078720.
*Mar  8 16:29:06.241: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar  8 16:29:06.241: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.16.61.100
*Mar  8 16:29:06.566: %CAPWAP-3-ERRORLOG: Unencrypted non-discovery CAPWAP Control Message from 172.16.61.100
*Mar  8 16:31:27.371: %CAPWAP-3-ERRORLOG: Unencrypted non-discovery CAPWAP Control Message from 172.16.61.100
*Mar  8 16:31:27.371: %CAPWAP-3-ERRORLOG: Invalid AC Message Type 34078720.
*Mar  8 16:31:27.372: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar  8 16:31:27.372: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.16.61.100
*Mar  8 16:31:27.696: %CAPWAP-3-ERRORLOG: Unencrypted non-discovery CAPWAP Control Message from 172.16.61.100
*Mar  8 16:31:27.696: %CAPWAP-3-ERRORLOG: Invalid AC Message Type 34078720.
*Mar  8 16:31:27.696: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar  8 16:31:27.697: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.16.61.100
*Mar  8 16:31:28.022: %CAPWAP-3-ERRORLOG: Unencrypted non-discovery CAPWAP Control Message from 172.16.61.100
*Mar  8 16:31:28.022: %CAPWAP-3-ERRORLOG: Invalid AC Message Type 34078720.
*Mar  8 16:31:28.023: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar  8 16:31:28.023: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.16.61.100
extracting c1240-k9w8-mx.124-21a.JHB1/6701.img (131328 bytes)
extracting c1240-k9w8-mx.124-21a.JHB1/info (295 bytes)
extracting info.ver (295 bytes)
Deleting target version: flash:/c1240-k9w8-mx.124-21a.JHB1...done.
New software image installed in flash:/c1240-k9w8-mx.124-21a.JHB1
Configuring system to use new image...done.
archive download: takes 282 seconds

Writing out the event log to nvram...

*Mar  8 16:32:56.535: image upgrade successfully, system is now reloading
*Mar  8 16:32:56.568: %SYS-4-PUPDATECLOCK: Periodic Clock update with ROMMON failed, because size left in ROMMON (4294967295), size needed (29), error code (-1)
*Mar  8 16:32:56.569: %SYS-5-RELOAD: Reload requested by capwap image download proc. Reload Reason: NEW IMAGE DOWNLOAD.
*Mar  8 16:32:56.569: %LWAPP-5-CHANGED: CAPWAP changed state to DOWNXmodem file system is available.
flashfs[0]: 10 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 7519232
flashfs[0]: Bytes available: 8479744
flashfs[0]: flashfs fsck took 32 seconds.
Base ethernet MAC Address: XXXX
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbps, full-duplex
Ethernet port 0 initialized: link is up
Loading "flash:/c1240-k9w8-mx.124-21a.JHB1/c1240-k9w8-mx.124-21a.JHB1"...########################################################################################################################################################################################################################################################################################################################################################################################################################################################################

File "flash:/c1240-k9w8-mx.124-21a.JHB1/c1240-k9w8-mx.124-21a.JHB1" uncompressed and installed, entry point: 0x3000
executing...

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706



Cisco IOS Software, C1240 Software (C1240-K9W8-M), Version 12.4(21a)JHB1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Wed 11-Aug-10 15:55 by prod_rel_team


Proceeding with system init

Proceeding to unmask interrupts
Initializing flashfs...

flashfs[1]: 10 files, 3 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 15482880
flashfs[1]: Bytes used: 7519232
flashfs[1]: Bytes available: 7963648
flashfs[1]: flashfs fsck took 7 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.

Radio0  present A506 7100 E8000000 A0000000 80000000 3
Radio1  present A506 6700 E8000100 A0040000 80010000 2
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
[email protected].

cisco AIR-LAP1242AG-C-K9   (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
Processor board ID FGL1453U071
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 6.0.199.4
1 FastEthernet interface
2 802.11 Radio(s)

32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: XXXX
Part Number                          : 73-10256-07
PCA Assembly Number                  : 800-26918-06
PCA Revision Number                  : A0
PCB Serial Number                    : FOC14493BLW
Top Assembly Part Number             : 800-29152-03
Top Assembly Serial Number           : FGL1453U071
Top Revision Number                  : A0
Product/Model Number                 : AIR-LAP1242AG-C-K9
% Please define a domain-name first.


Press RETURN to get started!


*Mar  1 00:00:09.031: soap_prepare_new_image_crash: mini ios flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx
*Mar  1 00:00:09.033:  set boothlpr to mini ios
*Mar  1 00:00:09.374: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar  1 00:00:10.984: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar  1 00:00:12.518: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar  1 00:00:12.630: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1024 messages)

*Mar  1 00:00:14.762: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar  1 00:00:14.803: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1240 Software (C1240-K9W8-M), Version 12.4(21a)JHB1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Wed 11-Aug-10 15:55 by prod_rel_team
*Mar  1 00:00:14.804: %SNMP-5-COLDSTART: SNMP agent on host ap is undergoing a cold start
*Mar  1 00:00:14.883: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar  1 00:00:15.109: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar  1 00:00:15.109: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar  1 00:00:15.109: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar  1 00:00:15.494: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
*Mar  1 00:00:15.771: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar  1 00:00:15.917: %DOT11-6-FREQ_SCAN: Interface Dot11Radio1, Scanning frequencies for 22 seconds
*Mar  1 00:00:16.110: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar  1 00:00:16.110: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar  1 00:00:16.389: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar  1 00:00:17.389: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar  1 00:00:25.233: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 172.16.200.44, mask 255.255.255.0, hostname AP

*Mar  1 00:00:33.786: %DOT11-6-FREQ_SCAN: Interface Dot11Radio1, Scanning frequencies for 8 seconds
*Mar  1 00:00:33.787: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar  1 00:00:33.815: %LINK-3-UPDOWN: Interface Dot11Radio0, c
*Mar  1 00:00:34.492: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
*Mar  1 00:00:41.572: %DOT11-6-FREQ_USED: Interface Dot11Radio1, frequency 5785 selected
*Mar  1 00:00:41.573: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar  1 00:00:42.573: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar  1 00:00:44.767: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.

Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)
*Mar  1 00:00:53.768: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER

*Mar  1 00:01:02.769: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER
*Mar  1 00:01:12.770: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Mar  8 16:35:21.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.61.100 peer_port: 5246
*Mar  8 16:35:21.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Mar  8 16:35:22.552: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.61.100 peer_port: 5246
*Mar  8 16:35:22.554: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.61.100
*Mar  8 16:35:22.554: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Mar  8 16:35:27.553: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.61.100
*Mar  8 16:35:27.699: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*Mar  8 16:35:27.857: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar  8 16:35:27.871: %CAPWAP-5-CHANGED: CAPWAP changed state to UP
*Mar  8 16:35:27.872: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Mar  8 16:35:27.872: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar  8 16:35:27.882: %LWAPP-3-CLIENTEVENTLOG: Received AP Syslog IP Address(255.255.255.255) configuration.
*Mar  8 16:35:28.013: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller WLCNAME
*Mar  8 16:35:28.068: %LWAPP-3-CLIENTEVENTLOG: SSID HNTZ1 added to the slot[0]
*Mar  8 16:35:28.071: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar  8 16:35:28.104: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar  8 16:35:28.872: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down

高版本WLC换低版本WLC  6.0->5.2

 

Xmodem file system is available.
flashfs[0]: 13 files, 4 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 12119040
flashfs[0]: Bytes available: 3879936
flashfs[0]: flashfs fsck took 43 seconds.
Base ethernet MAC Address: XXXX
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbps, full-duplex
Ethernet port 0 initialized: link is up
button pressed for 2 seconds
process_config_recovery: set IP address and config to default 10.0.0.1
Loading "flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx"...#################################################################################################################################################################################################################################################################

File "flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx" uncompressed and installed, entry point: 0x3000
executing...

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706



Cisco IOS Software, C1240 Software (C1240-RCVK9W8-M), Version 12.4(21a)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 02-Nov-09 18:40 by prod_rel_team


Proceeding with system init

Proceeding to unmask interrupts
Initializing flashfs...

flashfs[1]: 13 files, 4 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 15998976
flashfs[1]: Bytes used: 12119040
flashfs[1]: Bytes available: 3879936
flashfs[1]: flashfs fsck took 6 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
[email protected].

cisco AIR-LAP1242AG-C-K9   (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
Processor board ID FGL1453U071
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 3.0.51.0
1 FastEthernet interface

32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: XXXX
Part Number                          : 73-10256-07
PCA Assembly Number                  : 800-26918-06
PCA Revision Number                  : A0
PCB Serial Number                    : FOC14493BLW
Top Assembly Part Number             : 800-29152-03
Top Assembly Serial Number           : FGL1453U071
Top Revision Number                  : A0
Product/Model Number                 : AIR-LAP1242AG-C-K9
% Please define a domain-name first.


Press RETURN to get started!


*Mar  1 00:00:07.752: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1024 messages)

*Mar  1 00:00:09.827: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar  1 00:00:09.875: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1240 Software (C1240-RCVK9W8-M), Version 12.4(21a)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 02-Nov-09 18:40 by prod_rel_team
*Mar  1 00:00:09.955: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar  1 00:00:10.465: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
*Mar  1 00:00:10.826: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar  1 00:00:18.322: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 172.16.200.45, mask 255.255.255.0, hostname AP

Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar  1 00:00:39.778: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.

Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)
*Mar  1 00:00:48.778: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER

*Mar  1 00:00:57.779: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER
*Mar  1 00:01:07.780: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Mar  8 16:51:25.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.61.100 peer_port: 5246
*Mar  8 16:51:25.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Mar  8 16:51:26.550: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.61.100 peer_port: 5246
*Mar  8 16:51:26.551: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.61.100
*Mar  8 16:51:26.552: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
examining image...
extracting info (295 bytes)
Image info:
    Version Suffix: k9w8-.124-21a.JHB1
    Image Name: c1240-k9w8-mx.124-21a.JHB1
    Version Directory: c1240-k9w8-mx.124-21a.JHB1
    Ios Image Size: 4813312
    Total Image Size: 4813312
    Image Feature: WIRELESS LAN|LWAPP
    Image Family: C1240
    Wireless Switch Management Version: 6.0.199.4
Not enough free space to download.
Check for crashinfo/radio coredump and non used image files...
Deleting flash:/c1240-k9w8-mx.124-18a.JA
*Mar  8 16:51:31.551: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.61.100perform archive download capwap:/c1240 tar file done (free up 4594688 bytes)
Extracting files...
c1240-k9w8-mx.124-21a.JHB1/ (directory) 0 (bytes)
extracting c1240-k9w8-mx.124-21a.JHB1/c1240-k9w8-mx.124-21a.JHB1 (4543348 bytes)
*Mar  8 16:51:31.621: %CAPWAP-5-CHANGED: CAPWAP changed state to IMAGE（这时亮蓝灯闪烁）
*Mar  8 16:53:50.124: %CAPWAP-3-ERRORLOG: Unencrypted non-discovery CAPWAP Control Message from 172.16.61.100
*Mar  8 16:53:50.124: %CAPWAP-3-ERRORLOG: Invalid AC Message Type 34078720.
*Mar  8 16:53:50.124: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar  8 16:53:50.124: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.16.61.100
*Mar  8 16:53:50.427: %CAPWAP-3-ERRORLOG: Unencrypted non-discovery CAPWAP Control Message from 172.16.61.100
*Mar  8 16:53:50.427: %CAPWAP-3-ERRORLOG: Invalid AC Message Type 34078720.
*Mar  8 16:53:50.428: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar  8 16:53:50.428: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.16.61.100
*Mar  8 16:53:50.751: %CAPWAP-3-ERRORLOG: Unencrypted non-discovery CAPWAP Control Message from 172.16.61.100
*Mar  8 16:56:11.956: %CAPWAP-3-ERRORLOG: Unencrypted non-discovery CAPWAP Control Message from 172.16.61.100
*Mar  8 16:56:11.956: %CAPWAP-3-ERRORLOG: Invalid AC Message Type 34078720.
*Mar  8 16:56:11.957: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar  8 16:56:11.957: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.16.61.100
*Mar  8 16:56:12.281: %CAPWAP-3-ERRORLOG: Unencrypted non-discovery CAPWAP Control Message from 172.16.61.100
*Mar  8 16:56:12.282: %CAPWAP-3-ERRORLOG: Invalid AC Message Type 34078720.
*Mar  8 16:56:12.282: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar  8 16:56:12.282: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.16.61.100
*Mar  8 16:56:12.609: %CAPWAP-3-ERRORLOG: Unencrypted non-discovery CAPWAP Control Message from 172.16.61.100
extracting c1240-k9w8-mx.124-21a.JHB1/6701.img (131328 bytes)
extracting c1240-k9w8-mx.124-21a.JHB1/info (295 bytes)
extracting info.ver (295 bytes)
Deleting target version: flash:/c1240-k9w8-mx.124-21a.JHB1...done.
New software image installed in flash:/c1240-k9w8-mx.124-21a.JHB1
Configuring system to use new image...done.
archive download: takes 294 seconds

Writing out the event log to nvram...

*Mar  8 16:56:25.329: image upgrade successfully, system is now reloading
*Mar  8 16:56:25.363: %SYS-4-PUPDATECLOCK: Periodic Clock update with ROMMON failed, because size left in ROMMON (4294967295), size needed (29), error code (-1)
*Mar  8 16:56:25.363: %SYS-5-RELOAD: Reload requested by capwap image download proc. Reload Reason: NEW IMAGE DOWNLOAD.
*Mar  8 16:56:25.364: %LWAPP-5-CHANGED: CAPWAP changed state to DOWNXmodem file system is available.
flashfs[0]: 10 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 7519744
flashfs[0]: Bytes available: 8479232
flashfs[0]: flashfs fsck took 32 seconds.
Base ethernet MAC Address: XXXX
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbps, full-duplex
Ethernet port 0 initialized: link is up
Loading "flash:/c1240-k9w8-mx.124-21a.JHB1/c1240-k9w8-mx.124-21a.JHB1"...########################################################################################################################################################################################################################################################################################################################################################################################################################################################################

File "flash:/c1240-k9w8-mx.124-21a.JHB1/c1240-k9w8-mx.124-21a.JHB1" uncompressed and installed, entry point: 0x3000
executing...

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706



Cisco IOS Software, C1240 Software (C1240-K9W8-M), Version 12.4(21a)JHB1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Wed 11-Aug-10 15:55 by prod_rel_team


Proceeding with system init

Proceeding to unmask interrupts
Initializing flashfs...

flashfs[1]: 10 files, 3 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 15482880
flashfs[1]: Bytes used: 7519744
flashfs[1]: Bytes available: 7963136
flashfs[1]: flashfs fsck took 7 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.

Radio0  present A506 7100 E8000000 A0000000 80000000 3
Radio1  present A506 6700 E8000100 A0040000 80010000 2
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
[email protected].

cisco AIR-LAP1242AG-C-K9   (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
Processor board ID FGL1453U071
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 6.0.199.4
1 FastEthernet interface
2 802.11 Radio(s)

32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: XXXX
Part Number                          : 73-10256-07
PCA Assembly Number                  : 800-26918-06
PCA Revision Number                  : A0
PCB Serial Number                    : FOC14493BLW
Top Assembly Part Number             : 800-29152-03
Top Assembly Serial Number           : FGL1453U071
Top Revision Number                  : A0
Product/Model Number                 : AIR-LAP1242AG-C-K9
% Please define a domain-name first.


Press RETURN to get started!


*Mar  1 00:00:09.081: soap_prepare_new_image_crash: mini ios flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx
*Mar  1 00:00:09.083:  set boothlpr to mini ios
*Mar  1 00:00:09.427: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar  1 00:00:11.037: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar  1 00:00:12.571: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar  1 00:00:12.682: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1024 messages)

*Mar  1 00:00:14.815: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar  1 00:00:14.856: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1240 Software (C1240-K9W8-M), Version 12.4(21a)JHB1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Wed 11-Aug-10 15:55 by prod_rel_team
*Mar  1 00:00:14.857: %SNMP-5-COLDSTART: SNMP agent on host ap is undergoing a cold start
*Mar  1 00:00:14.936: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar  1 00:00:15.162: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar  1 00:00:15.162: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar  1 00:00:15.162: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar  1 00:00:15.546: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
*Mar  1 00:00:15.815: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar  1 00:00:15.937: %DOT11-6-FREQ_SCAN: Interface Dot11Radio1, Scanning frequencies for 17 seconds
*Mar  1 00:00:16.170: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar  1 00:00:16.170: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar  1 00:00:16.422: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar  1 00:00:17.423: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar  1 00:00:25.286: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 172.16.200.46, mask 255.255.255.0, hostname AP

*Mar  1 00:00:33.414: %DOT11-6-FREQ_USED: Interface Dot11Radio1, frequency 5765 selected
*Mar  1 00:00:33.415: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar  1 00:00:33.817: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar  1 00:00:33.845: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar  1 00:00:33.845: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar  1 00:00:33.875: %LINK-3-UPDOWN: Interface Dot11Radio0, c
*Mar  1 00:00:34.415: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar  1 00:00:44.818: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.

Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)
*Mar  1 00:00:53.819: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER

*Mar  1 00:01:02.820: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER
*Mar  1 00:01:12.821: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Mar  8 16:58:49.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.61.100 peer_port: 5246  （粉 黄绿 互闪）
*Mar  8 16:58:49.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Mar  8 16:58:50.552: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.61.100 peer_port: 5246
*Mar  8 16:58:50.554: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.61.100
*Mar  8 16:58:50.554: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Mar  8 16:58:55.553: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.61.100
*Mar  8 16:58:55.698: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*Mar  8 16:58:55.856: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar  8 16:58:55.870: %CAPWAP-5-CHANGED: CAPWAP changed state to UP
*Mar  8 16:58:55.871: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Mar  8 16:58:55.871: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar  8 16:58:55.881: %LWAPP-3-CLIENTEVENTLOG: Received AP Syslog IP Address(255.255.255.255) configuration.
*Mar  8 16:58:56.015: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller WLCNAME
*Mar  8 16:58:56.069: %LWAPP-3-CLIENTEVENTLOG: SSID (名字） added to the slot[0]
*Mar  8 16:58:56.072: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar  8 16:58:56.105: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar  8 16:58:56.870: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down

AP切换H-HEAP模式

 

Writing out the event log to nvram...

*Mar  8 16:59:45.234: %SYS-5-RELOAD: Reload requested by CAPWAP CLIENT. Reload Reason: Recvd RESET req from Controller.
*Mar  8 16:59:45.238: %LWAPP-5-CHANGED: CAPWAP changed state to DOWNXmodem file system is available.
flashfs[0]: 10 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 7524864
flashfs[0]: Bytes available: 8474112
flashfs[0]: flashfs fsck took 32 seconds.
Base ethernet MAC Address: XXXX
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbps, full-duplex
Ethernet port 0 initialized: link is up
Loading "flash:/c1240-k9w8-mx.124-21a.JHB1/c1240-k9w8-mx.124-21a.JHB1"...########################################################################################################################################################################################################################################################################################################################################################################################################################################################################

File "flash:/c1240-k9w8-mx.124-21a.JHB1/c1240-k9w8-mx.124-21a.JHB1" uncompressed and installed, entry point: 0x3000
executing...

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706



Cisco IOS Software, C1240 Software (C1240-K9W8-M), Version 12.4(21a)JHB1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Wed 11-Aug-10 15:55 by prod_rel_team


Proceeding with system init

Proceeding to unmask interrupts
Initializing flashfs...

flashfs[1]: 10 files, 3 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 15482880
flashfs[1]: Bytes used: 7524864
flashfs[1]: Bytes available: 7958016
flashfs[1]: flashfs fsck took 4 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.

Radio0  present A506 7100 E8000000 A0000000 80000000 3
Radio1  present A506 6700 E8000100 A0040000 80010000 2
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
[email protected].

cisco AIR-LAP1242AG-C-K9   (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
Processor board ID FGL1453U071
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 6.0.199.4
1 FastEthernet interface
2 802.11 Radio(s)

32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: XXXX
Part Number                          : 73-10256-07
PCA Assembly Number                  : 800-26918-06
PCA Revision Number                  : A0
PCB Serial Number                    : FOC14493BLW
Top Assembly Part Number             : 800-29152-03
Top Assembly Serial Number           : FGL1453U071
Top Revision Number                  : A0
Product/Model Number                 : AIR-LAP1242AG-C-K9
% Please define a domain-name first.


Press RETURN to get started!


*Mar  1 00:00:06.315: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS ged state to up
*Mar  1 00:00:11.391: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1240 Software (C1240-K9W8-M), Version 12.4(21a)JHB1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Wed 11-Aug-10 15:55 by prod_rel_team
*Mar  1 00:00:11.392: %SNMP-5-COLDSTART: SNMP agent on host AP is undergoing a cold start
*Mar  1 00:00:11.469: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar  1 00:00:11.694: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar  1 00:00:11.694: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar  1 00:00:11.694: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar  1 00:00:11.932: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar  1 00:00:11.932: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar  1 00:00:12.078: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
*Mar  1 00:00:12.334: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar  1 00:00:12.518: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar  1 00:00:12.698: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar  1 00:00:12.698: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Mar  1 00:00:12.950: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar  1 00:00:13.960: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar  1 00:00:21.818: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 172.16.200.47, mask 255.255.255.0, hostname AP

*Mar  1 00:00:30.292: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar  1 00:00:30.319: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar  1 00:00:30.319: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar  1 00:00:30.349: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar  1 00:00:30.985: Logging LWAPP message to 255.255.255.255.

*Mar  1 00:00:31.034: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar  1 00:00:42.032: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.

Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)
*Mar  1 00:00:51.034: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER

*Mar  1 00:01:00.035: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER
*Mar  1 00:01:10.037: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Mar  8 17:02:07.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.61.100 peer_port: 5246
*Mar  8 17:02:07.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Mar  8 17:02:08.559: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.61.100 peer_port: 5246
*Mar  8 17:02:08.560: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.61.100
*Mar  8 17:02:08.560: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Mar  8 17:02:13.559: %CAPWAP-5-SENDJOIN: sending Join RequestEVENTLOG: OfficeExtend Localssid saved in AP flash
*Mar  8 17:02:13.894: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Mar  8 17:02:13.894: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar  8 17:02:14.251: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar  8 17:02:14.253: %LWAPP-3-CLIENTEVENTLOG: SSID （名字） added to the slot[0]
*Mar  8 17:02:14.397: %LWAPP-3-CLIENTEVENTLOG: SSID （名字） added to the slot[1]
*Mar  8 17:02:14.430: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar  8 17:02:14.464: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar  8 17:02:14.467: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar  8 17:02:14.499: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar  8 17:02:14.894: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar  8 17:02:15.158: %LWAPP-3-CLIENTEVENTLOG: SSID （名字） added to the slot[1]
*Mar  8 17:02:15.490: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar  8 17:02:15.492: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar  8 17:02:15.525: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar  8 17:02:15.809: %WIDS-6-ENABLED: IDS Signature is loaded and enabled

AP切换AP GROUP日志

Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)
*Mar  1 00:00:50.400: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER

*Mar  1 00:00:59.401: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER
*Mar  1 00:01:09.403: %CAPWAP-3-ERRORLOG: Go join a capwap con
*Mar  8 15:47:09.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.61.100 peer_port: 5246
*Mar  8 15:47:09.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Mar  8 15:47:10.566: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.61.100 peer_port: 5246
*Mar  8 15:47:10.567: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.61.100
*Mar  8 15:47:10.568: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Mar  8 15:47:15.567: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.61.100
*Mar  8 15:47:15.722: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*Mar  8 15:47:15.881: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar  8 15:47:15.895: %CAPWAP-5-CHANGED: CAPWAP changed state to UP
*Mar  8 15:47:15.902: %LWAPP-3-CLIENTEVENTLOG: OfficeExtend Localssid saved in AP flash
*Mar  8 15:47:15.915: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Mar  8 15:47:15.915: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar  8 15:47:16.063: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller wlcname
*Mar  8 15:47:16.112: %LWAPP-3-CLIENTEVENTLOG: SSID （名字） added to the slot[0]
*Mar  8 15:47:16.282: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar  8 15:47:16.284: %LWAPP-3-CLIENTEVENTLOG: SSID (名字） added to the slot[1]
*Mar  8 15:47:16.912: %WIDS-6-ENABLED: IDS Signature is loaded and enabled
*Mar  8 15:47:16.914: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down