suse 10 网卡绑定
Suse10网卡绑定
1.建立配置文件
localhost:/etc/sysconfig/network #touch /etc/modprobe.d/bonding.conf
localhost:/etc/sysconfig/network #vim /etc/modprobe.d/bonding.conf
alias bond0 bonding
options bond0 miimon=100 mode=1
2.配置网卡
localhost:/etc/sysconfig/network # touch ifcfg-bond0
localhost:/etc/sysconfig/network # vim ifcfg-bond0 //添加如下配置
BOOTPROTO='static'
IPADDR='192.168.0.88'
NETMASK='255.255.255.0'
STARTMODE='onboot'
BONDING_MASTER="yes"
BONDING_MODULE_OPTS="mode=active-backup miimon=100 use_carrier=1"
BONDING_SLAVE0='bus-pci-0000:02:01.0'
BONDING_SLAVE1='bus-pci-0000:02:05.0'
注意：文件中SLAVE_PCI码特别重要，获取方式如下（eth1网卡雷同）：
localhost:/etc/sysconfig/network # ethtool -i eth0
driver: vmxnet
version: 2.0.8.0
firmware-version: N/A
bus-info: 0000:02:01.0
3.建立网卡mac配置文件（suse网卡默认网卡配置文件为ifcfg-eth-id-xx。。）新添加的网卡没有配置文件可以用ifconfig | grep HWaddr来获取新网卡的mac地址来建立配置文件！
建立ifcfg-eth-id-00\:0C\:29\:57\:19\:FD和ifcfg-eth-id-00\:0c\:29\:57\:19\:f3配置文件
localhost:/etc/sysconfig/network # cat ifcfg-eth-id-00\:0C\:29\:57\:19\:FD
ONBOOT=yes
BOOTPROTO=none
MASTER=bond0
SLAVE=yes
USERCTL=no
localhost:/etc/sysconfig/network # cat ifcfg-eth-id-00\:0c\:29\:57\:19\:f3
ONBOOT=yes
BOOTPROTO=none
MASTER=bond0
SLAVE=yes
USERCTL=no
4添加网卡驱动：
localhost:/etc/sysconfig/network # modprobe bonding
5重新启动网卡：
localhost:/etc/sysconfig/network # rcnetwork restart
6检查绑定情况：
localhost:~ # cat /proc/net/bonding/bond0
Ethernet Channel Bonding Driver: v3.0.1 (January 9, 2006)
Bonding Mode: fault-tolerance (active-backup)
Primary Slave: None
Currently Active Slave: eth0
MII Status: up //此及以下三个UP表示成功
！！
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0
Slave Interface: eth0
MII Status: up
Link Failure Count: 0
Permanent HW addr: 00:0c:29:57:19:f3
Slave Interface: eth1
MII Status: up
Link Failure Count: 0
Permanent HW addr: 00:0c:29:57:19:fd
或者是：
localhost:~ # ifconfig | grep HWaddr //MAC地址一致也表示成功！
bond0 Link encap:Ethernet HWaddr 00:0C:29:57:19:F3
eth0 Link encap:Ethernet HWaddr 00:0C:29:57:19:F3
eth1 Link encap:Ethernet HWaddr 00:0C:29:57:19:F3