Android gingerbread eMMC booting
Android gingerbread eMMC booting
 |
This page is currently under construction. The content of this page is due to change quite frequently and thus the quality and accuracy are not guaranteed until this message has been removed. Please feel free to contribute to this page while construction is in progress. |
Contents[hide]
|
Introduction
- AM37xevm has on board NAND and MMC interface.Either interface can be used for booting a system.
- NAND boot is raw boot, as it reads raw data and manipulate it.
- MMC boot is FAT boot, as it reads file from mmc sector and manipulated it.
- eMMC boot can be FAT boot or raw boot.
- MMC and NAND boot is already supported by android devkit releases available at http://arowboat.org
- This wiki highlights on
- Adding eMMC support for fastboot
- Updating images to eMMC over fastboot
- eMMC boot
- Wiki will also act as porting guide to port eMMC support on other platforms.
Note: All patches described in this documents are validated on Texas Intruments's AM37xevm board.
What is eMMC?
eMMC describes an architecture consisting of an embedded storage solution with MMC interface, flash memory and controller.In one line it is a flash/nand over MMC interface.
The OMAP processor follows a 2 stage boot process. Details on the boot procedure can be found at the [boot sequence] page.
What is fastboot?
- Fastboot is the method that android uses to flash the android build onto the target.
- Fastboot protocol specification is found HERE
- Fastboot speeds up your development NOT the time it takes to boot.
- Also,fastboot is used to updated x-loader,bootloader,kernel,systemfs,userdata etc. by oem
eMMC layout
- In the discussion that follows, “sector” refers to a 512-byte disk sector, addressed by its Logical Block Address (LBA). Although the UEFI specs allow for disk sectors of other sizes, in practice 512 bytes is the norm.
Protective master boot record
The master boot record is the first sector on the hard drive (LBA 0). As mentioned above, legacy BIOSes will boot from this sector. To protect the GUID partitions on the drive from legacy OSes, the MBR partition table normally contains a single partition entry of type 0xEE, filling the entire drive.
GUID Partition Table (GPT)
The second sector (LBA 1) contains the primary GPT header, followed immediately by 16K (32 sectors) of the primary GUID Partition Entry Array. In conformance with the EFI spec, another copy of these data should be located at the end of the disk as well, with the secondary GPT header in the last accessible sector and the secondary GUID Partition Entry Array immediately preceding it.In current implementation secondary GPT is not included.
eMMC partition layout
- GPT allows a large number of partitions on a drive.Choosing a parition scheme may vary across oem vendor.Partition scheme described here is most choosen by oem for mobile/handheld device.
| Partition# | Name# | Size# | Strat LBA-End LBR | Description# |
| 0 | MBR & GPT | 0x00000000-0x000000FF | Master Boot Record and GUID Partition Table | |
| 1 | x-loader(MLO) | 256KB | 0x00000100-0x000001FF | First stage bootloader |
| 2 | bootloader(u-boot.bin) | 384KB | 0x00000200-0x000005FF | Second stage bootloader |
| 3 | misc | 128KB | 0x00000600-0x000006FF | Reserved.This partition can be used for internal purpose |
| 4 | recovery (zImage + recovery-ramdisk.img) | 8MB | 0x00000A00-0x000049FF | recovery partition |
| 5 | boot (boot.img = zImage + ramdisk.img) | 8MB | 0x00004A00-0x000089FF | Partition contains kernel + ramdisk images. |
| 6 | system (system.img) | 256MB | 0x00008A00-0x000889FF | android file system |
| 7 | cache (cache.img) | 32MB | 0x00088A00-0x000989FF | Partition will be used to store application cache |
| 8 | userdata (userdata.img) | 32MB | 0x00098A00-0x000A89FF | Partition contains userdata supplied by oem vendor like configuration files,utilities etc.. |
| 9 | media | Remaining | 0x000A8A00-0x00762761 | Partition contains media files; supplied by oem vendor |
Fastboot flowchart
Adding a support on am37xevm for eMMC fastboot update
Download patches for x-loader,u-boot and kernel
- Download patch files from [HERE]
/* go to user directory */ $cd <MY_DIR> /* extract downloader patch files */ $tar -xzvf EMMC_patch_rev01.tar.gz
x-loader build
- Download source(if it is not downloaded) and apply patch
/* download x-loader source if not available */ $git clone git://gitorious.org/rowboat/x-loader.git $cd x-loader /* checkout mentioned commit id */ $git checkout e6e39e34104f28b8bd62307971ab89e736cb9388 /* apply patch for raw boot */ $git am <MY_DIR>/EMMC_patch_rev01/x-loader/0001-eMMC-raw-boot-support-is-added.patch
- Build x-loader
$make CROSS_COMPILE=arm-eabi- distclean $make CROSS_COMPILE=arm-eabi- omap3evm_config $make CROSS_COMPILE=arm-eabi-
This command will build the x-loader Image "x-load.bin" To create the MLO file used for booting from a MMC/SD card, sign the x-loader image using the signGP tool found in the Tools/signGP directory of the Devkit.
Note: you will need to copy the signGP tool from the Tools/signGP directory to the directory that contains the x-load.bin file $ ./signGP ./x-load.bin
The signGP tool will create a .ift file, rename the x-load.bin.ift to MLO $ mv x-load.bin.ift MLO
- Append eMMC raw header
- Download eMMC raw header :'eMMC_raw_header' (right click and "save link as")
$dd if=<eMMC_raw_header> of=./MLO.final $dd if=<MLO-Path>/MLO of=./MLO.final conv=notrunc oflag=append
u-boot build
- Download source(if it is not downloaded)and apply patch
/* download u-boot source if not available */ $git clone git://gitorious.org/rowboat/u-boot.git $cd u-boot /* checkout mentioned commit id */ $git checkout 81c20af53410ac7201ee18de66579b758c94c970 /* apply patches for eMMC and fastboot updat*/ $git am <MY_DIR>/EMMC_patch_rev01/u-boot/0001-GPT-partition-creation.patch $git am <MY_DIR>/EMMC_patch_rev01/u-boot/0002-fastboot-support-for-eMMC-partition.patch $git am <MY_DIR>/EMMC_patch_rev01/u-boot/0003-eMMC-raw-boot-support-is-added.patch
- Build u-boot
$make CROSS_COMPILE=arm-eabi- distclean $make CROSS_COMPILE=arm-eabi- omap3_evm_config $make CROSS_COMPILE=arm-eabi-
kernel build
- Download source(if it is not downloaded)and apply patch
/* download u-boot source if not available */ $git clone git://gitorious.org/rowboat/kernel.git $cd kernel /* checkout mentioned commit id, branch is:rowboat-kernel-2.6.37 */ $git checkout 1a12433ffdd56a2b87504b3fe5efdcb924c90553 /* apply patches for EFI and ext4 file system support*/ $git am <MY_DIR>/EMMC_patch_rev01/kernel/0001-enabling-ext4-and-EFI-file-system-support.patch
- Build kernel
$make ARCH=arm CROSS_COMPILE=arm-eabi- distclean $make ARCH=arm CROSS_COMPILE=arm-eabi- omap3_evm_android_defconfig $make ARCH=arm CROSS_COMPILE=arm-eabi- uImage
buid android file system
- Follow build step given at#[HERE]
Prepare Images
boot.img
$mkdir <YOUR_PATH>/images $cd <YOUR_PATH>/images $cp <ANDROID_SOURCE>/kernel/arch/arm/boot/zImage .
- Update init.rc file and rebuit images
- Add following lines to <ANDROID_SOURCE>/out/target/product/omap3evm/root/init.rc
on fs
mount ext4 /dev/block/mmcblk0p6 /system wait ro
mount ext4 /dev/block/mmcblk0p8 /data wait noatime nosuid nodev
mount ext4 /dev/block/mmcblk0p7 /cache wait noatime nosuid nodev
- Rebuilt images
$cd <ANDROID_SOURCE>
$find out/target/product/omap3evm -name *.img -exec rm -f {} \;
$make TARGET_PRODUCT=omap3evm OMAPES=5.x
- Prepare boot.img
$cp <ANDROID_SOURCE>/out/target/product/omap3evm/ramdisk.img . $cp <ANDROID_SOURCE>/out/host/linux-x86/bin/mkbootimg . $./mkbootimg --kernel zImage --ramdisk ramdisk.img --base 0x80000000 --cmdline "console=ttyO0,115200n8 androidboot.console=ttyO0 mem=256M root=/dev/ram0 rw initramfs=0x81000000,8M init=/init ip=off omap_vout.vid1_static_vrfb_alloc=y vram="2M" omapfb.vram=0:2M" -o boot.img
system.img
$cd <YOUR_PATH>/images /* creating 250MB, it can be configure as per need */ $dd if=/dev/zero of=./system.img bs=1M count=250 $mkfs.ext4 system.img $mkdir mnt-point $sudo mount -t ext4 -o loop system.img mnt-point/ $cp -rfp <ANDROID_SOURCE>/out/target/product/omap3evm/system/* mnt-point/ $sudo umount mnt-point
userdata.img
$cd <YOUR_PATH>/images /* creating 30MB, it can be configure as per need */ $dd if=/dev/zero of=./userdata.img bs=1M count=30 $mkfs.ext4 userdata.img $sudo mount -t ext4 -o loop userdata.img mnt-point/ $cp -rfp <ANDROID_SOURCE>/out/target/product/omap3evm/data/* mnt-point/ $cp -rfp <ANDROID_SOURCE>/out/target/product/omap3evm/root/data/* mnt-point/ $sudo umount mnt-point
cache.img
$cd <YOUR_PATH>/images /* creating 30MB, it can be configure as per need */ $dd if=/dev/zero of=./cache.img bs=1M count=30 $mkfs.ext4 cache.img
Using Fastboot
Creating the GPT table on eMMC and flash raw images
- Create mmc card for FAT boot mentioned at HERE
- On Target
- Connect target to host machine using USB cable.Connect USB cable to OTG port on target
- Boot target with a stock u-boot and MLO
- Prompt at u-boot and enter following command
#fastboot Fastboot entered...
- On Host Machine
/* locate fastboot in android filesystem */ $cd <ANDROID_SOURCE>/out/host/linux-x86/bin/ /* search for fastboot devices */ $./fastboot devices /* create GPT table on eMMC/SD card */ $./fastboot oem format /* flash all partitions: ./fastboot flash <name> <binary> */ /* flash xloader */ $./fastboot flash xloader ./MLO.final /* flash bootloader */ $./fastboot flash bootloader ./u-boot.bin /* flash boot image */ $./fastboot flash boot ./boot.img /* flash file system - system image */ $./fastboot flash system ./system.img /* flash user data */ $./fastboot flash userdata ./userdata.img /* flash cache partition */ $./fastboot flash cache ./cache.img /* reboot target */ $./fastboot reboot
How to change GPT configuration
- GPT configuration has been defined in "<ANDROID_PATH>/u-boot/board/ti/evm/mmc.c" as below. Kindly change as per need
static struct partition partitions[] = {
{ "-", 128 },
{ "xloader", 128 },
{ "bootloader", 512 },
/* "misc" partition is required for recovery */
{ "misc", 128 },
{ "-", 384 },
{ "recovery", 8*1024 },
{ "boot", 8*1024 },
{ "system", 256*1024 },
{ "cache", 32*1024 },
{ "userdata", 32*1024},
{ "media", 0 },
{ 0, 0 },
};
Technical Support and Product Updates
For further information or to report any problems, contact
http://e2e.ti.com/android
http://support.ti.com
For community support join
http://groups.google.com/group/rowboat
For IRC #rowboat on irc.freenode.net