和菜鸟一起学linux总线驱动之初识i2c驱动数据传输流程
吃个晚饭，画个流程图，没想到已经这么晚了。还是速度把这篇文章搞定，收拾回去了。
先看下linux中的i2c的数据流程图吧。这里主要是用gpio模拟的i2c的。
还是具体看下代码吧，流程只是个大概，和i2c的总线协议差不多的。
首先从数据调用来看吧。一般的都是通过
i2c_transfer来来实现的，
int i2c_transfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num)
{
unsigned long orig_jiffies;
int ret, try;
if (adap->algo->master_xfer) {
#ifdef DEBUG
for (ret = 0; ret < num; ret++) {
dev_dbg(&adap->dev, "master_xfer[%d] %c, addr=0x%02x, "
"len=%d%s\n", ret, (msgs[ret].flags & I2C_M_RD)
? 'R' : 'W', msgs[ret].addr, msgs[ret].len,
(msgs[ret].flags & I2C_M_RECV_LEN) ? "+" : "");
}
#endif
if (in_atomic() || irqs_disabled()) {
ret = i2c_trylock_adapter(adap);
if (!ret)
/* I2C activity is ongoing. */
return -EAGAIN;
} else {
i2c_lock_adapter(adap);
}
/* Retry automatically on arbitration loss */
orig_jiffies = jiffies;
for (ret = 0, try = 0; try <= adap->retries; try++) {
ret = adap->algo->master_xfer(adap, msgs, num);
if (ret != -EAGAIN)
break;
if (time_after(jiffies, orig_jiffies + adap->timeout))
break;
}
i2c_unlock_adapter(adap);
return ret;
} else {
dev_dbg(&adap->dev, "I2C level transfers not supported\n");
return -EOPNOTSUPP;
}
}
adap->algo->master_xfer，通过这个函数指针，这个函数指针赋值先看下面的代码
在drivers/i2c/busses/i2c-gpio.c中
static int __devinit i2c_gpio_probe(struct platform_device *pdev)
{
struct i2c_gpio_platform_data *pdata;
struct i2c_algo_bit_data *bit_data;
struct i2c_adapter *adap;
int ret;
pdata = pdev->dev.platform_data;
if (!pdata)
return -ENXIO;
ret = -ENOMEM;
adap = kzalloc(sizeof(struct i2c_adapter), GFP_KERNEL);
if (!adap)
goto err_alloc_adap;
bit_data = kzalloc(sizeof(struct i2c_algo_bit_data), GFP_KERNEL);
if (!bit_data)
goto err_alloc_bit_data;
ret = gpio_request(pdata->sda_pin, "sda");
if (ret)
goto err_request_sda;
ret = gpio_request(pdata->scl_pin, "scl");
if (ret)
goto err_request_scl;
if (pdata->sda_is_open_drain) {
gpio_direction_output(pdata->sda_pin, 1);
bit_data->setsda = i2c_gpio_setsda_val;
} else {
gpio_direction_input(pdata->sda_pin);
bit_data->setsda = i2c_gpio_setsda_dir;
}
if (pdata->scl_is_open_drain || pdata->scl_is_output_only) {
gpio_direction_output(pdata->scl_pin, 1);
bit_data->setscl = i2c_gpio_setscl_val;
} else {
gpio_direction_input(pdata->scl_pin);
bit_data->setscl = i2c_gpio_setscl_dir;
}
if (!pdata->scl_is_output_only)
bit_data->getscl = i2c_gpio_getscl;
bit_data->getsda = i2c_gpio_getsda;
if (pdata->udelay)
bit_data->udelay = pdata->udelay;
else if (pdata->scl_is_output_only)
bit_data->udelay = 50; /* 10 kHz */
else
bit_data->udelay = 5; /* 100 kHz */
if (pdata->timeout)
bit_data->timeout = pdata->timeout;
else
bit_data->timeout = HZ / 10; /* 100 ms */
bit_data->data = pdata;
adap->owner = THIS_MODULE;
snprintf(adap->name, sizeof(adap->name), "i2c-gpio%d", pdev->id);
adap->algo_data = bit_data;
adap->class = I2C_CLASS_HWMON | I2C_CLASS_SPD;
adap->dev.parent = &pdev->dev;
/*
* If "dev->id" is negative we consider it as zero.
* The reason to do so is to avoid sysfs names that only make
* sense when there are multiple adapters.
*/
adap->nr = (pdev->id != -1) ? pdev->id : 0;
ret = i2c_bit_add_numbered_bus(adap);
if (ret)
goto err_add_bus;
platform_set_drvdata(pdev, adap);
dev_info(&pdev->dev, "using pins %u (SDA) and %u (SCL%s)\n",
pdata->sda_pin, pdata->scl_pin,
pdata->scl_is_output_only
? ", no clock stretching" : "");
return 0;
err_add_bus:
gpio_free(pdata->scl_pin);
err_request_scl:
gpio_free(pdata->sda_pin);
err_request_sda:
kfree(bit_data);
err_alloc_bit_data:
kfree(adap);
err_alloc_adap:
return ret;
}
看到了
ret = i2c_bit_add_numbered_bus(adap);
然后这个函数是在
Drivers/i2c/algo/i2c-algo-bit.c中
int i2c_bit_add_numbered_bus(struct i2c_adapter *adap)
{
return __i2c_bit_add_bus(adap, i2c_add_numbered_adapter);
}
然后
int i2c_bit_add_bus(struct i2c_adapter *adap)
{
return __i2c_bit_add_bus(adap, i2c_add_adapter);
}
接着调用这个函数
static int __i2c_bit_add_bus(struct i2c_adapter *adap,
int (*add_adapter)(struct i2c_adapter *))
{
struct i2c_algo_bit_data *bit_adap = adap->algo_data;
int ret;
if (bit_test) {
ret = test_bus(adap);
if (ret < 0)
return -ENODEV;
}
/* register new adapter to i2c module... */
adap->algo = &i2c_bit_algo;
adap->retries = 3;
ret = add_adapter(adap);
if (ret < 0)
return ret;
/* Complain if SCL can't be read */
if (bit_adap->getscl == NULL) {
dev_warn(&adap->dev, "Not I2C compliant: can't read SCL\n");
dev_warn(&adap->dev, "Bus may be unreliable\n");
}
return 0;
}
然后可以看到这两句
adap->algo = &i2c_bit_algo;
adap->retries = 3;
算法指向了i2c_bit_algo，尝试3次。
接着，我们回到刚才的调用adap->algo->master_xfer。然后就是
static const struct i2c_algorithm i2c_bit_algo = {
.master_xfer = bit_xfer,
.functionality = bit_func,
};
这个函数指针调用的是bit_xfer函数
static int bit_xfer(struct i2c_adapter *i2c_adap,
struct i2c_msg msgs[], int num)
{
struct i2c_msg *pmsg;
struct i2c_algo_bit_data *adap = i2c_adap->algo_data;
int i, ret;
unsigned short nak_ok;
if (adap->pre_xfer) {
ret = adap->pre_xfer(i2c_adap);
if (ret < 0)
return ret;
}
bit_dbg(3, &i2c_adap->dev, "emitting start condition\n");
i2c_start(adap);
for (i = 0; i < num; i++) {
pmsg = &msgs[i];
nak_ok = pmsg->flags & I2C_M_IGNORE_NAK;
if (!(pmsg->flags & I2C_M_NOSTART)) {
if (i) {
bit_dbg(3, &i2c_adap->dev, "emitting "
"repeated start condition\n");
i2c_repstart(adap);
}
ret = bit_doAddress(i2c_adap, pmsg);
if ((ret != 0) && !nak_ok) {
bit_dbg(1, &i2c_adap->dev, "NAK from "
"device addr 0x%02x msg #%d\n",
msgs[i].addr, i);
goto bailout;
}
}
if (pmsg->flags & I2C_M_RD) {
/* read bytes into buffer*/
ret = readbytes(i2c_adap, pmsg);
if (ret >= 1)
bit_dbg(2, &i2c_adap->dev, "read %d byte%s\n",
ret, ret == 1 ? "" : "s");
if (ret < pmsg->len) {
if (ret >= 0)
ret = -EREMOTEIO;
goto bailout;
}
} else {
/* write bytes from buffer */
ret = sendbytes(i2c_adap, pmsg);
if (ret >= 1)
bit_dbg(2, &i2c_adap->dev, "wrote %d byte%s\n",
ret, ret == 1 ? "" : "s");
if (ret < pmsg->len) {
if (ret >= 0)
ret = -EREMOTEIO;
goto bailout;
}
}
}
ret = i;
bailout:
bit_dbg(3, &i2c_adap->dev, "emitting stop condition\n");
i2c_stop(adap);
if (adap->post_xfer)
adap->post_xfer(i2c_adap);
return ret;
}
这里就是算法的所有过程了。根据协议来，先发个i2c_start(adap);
/* --- other auxiliary functions -------------------------------------- */
static void i2c_start(struct i2c_algo_bit_data *adap)
{
/* assert: scl, sda are high */
setsda(adap, 0);
udelay(adap->udelay);
scllo(adap);
}
然后再发送设备地址，ret = bit_doAddress(i2c_adap, pmsg);
static int bit_doAddress(struct i2c_adapter *i2c_adap, struct i2c_msg *msg)
{
unsigned short flags = msg->flags;
unsigned short nak_ok = msg->flags & I2C_M_IGNORE_NAK;
struct i2c_algo_bit_data *adap = i2c_adap->algo_data;
unsigned char addr;
int ret, retries;
retries = nak_ok ? 0 : i2c_adap->retries;
if (flags & I2C_M_TEN) {
/* a ten bit address */
addr = 0xf0 | ((msg->addr >> 7) & 0x06);
bit_dbg(2, &i2c_adap->dev, "addr0: %d\n", addr);
/* try extended address code...*/
ret = try_address(i2c_adap, addr, retries);
if ((ret != 1) && !nak_ok) {
dev_err(&i2c_adap->dev,
"died at extended address code\n");
return -EREMOTEIO;
}
/* the remaining 8 bit address */
ret = i2c_outb(i2c_adap, msg->addr & 0xff);
if ((ret != 1) && !nak_ok) {
/* the chip did not ack / xmission error occurred */
dev_err(&i2c_adap->dev, "died at 2nd address code\n");
return -EREMOTEIO;
}
if (flags & I2C_M_RD) {
bit_dbg(3, &i2c_adap->dev, "emitting repeated "
"start condition\n");
i2c_repstart(adap);
/* okay, now switch into reading mode */
addr |= 0x01;
ret = try_address(i2c_adap, addr, retries);
if ((ret != 1) && !nak_ok) {
dev_err(&i2c_adap->dev,
"died at repeated address code\n");
return -EREMOTEIO;
}
}
} else { /* normal 7bit address */
addr = msg->addr << 1;
if (flags & I2C_M_RD)
addr |= 1;
if (flags & I2C_M_REV_DIR_ADDR)
addr ^= 1;
ret = try_address(i2c_adap, addr, retries);
if ((ret != 1) && !nak_ok)
return -ENXIO;
}
return 0;
}
这里尝试3次，ret = try_address(i2c_adap, addr, retries);
static int try_address(struct i2c_adapter *i2c_adap,
unsigned char addr, int retries)
{
struct i2c_algo_bit_data *adap = i2c_adap->algo_data;
int i, ret = 0;
for (i = 0; i <= retries; i++) {
ret = i2c_outb(i2c_adap, addr);
if (ret == 1 || i == retries)
break;
bit_dbg(3, &i2c_adap->dev, "emitting stop condition\n");
i2c_stop(adap);
udelay(adap->udelay);
yield();
bit_dbg(3, &i2c_adap->dev, "emitting start condition\n");
i2c_start(adap);
}
if (i && ret)
bit_dbg(1, &i2c_adap->dev, "Used %d tries to %s client at "
"0x%02x: %s\n", i + 1,
addr & 1 ? "read from" : "write to", addr >> 1,
ret == 1 ? "success" : "failed, timeout?");
return ret;
}
这个ret = i2c_outb(i2c_adap, addr);是发送一个字节的函数，其具体就是通过gpio的拉高拉低来实现的
/* send a byte without start cond., look for arbitration,
check ackn. from slave */
/* returns:
* 1 if the device acknowledged
* 0 if the device did not ack
* -ETIMEDOUT if an error occurred (while raising the scl line)
*/
static int i2c_outb(struct i2c_adapter *i2c_adap, unsigned char c)
{
int i;
int sb;
int ack;
struct i2c_algo_bit_data *adap = i2c_adap->algo_data;
/* assert: scl is low */
for (i = 7; i >= 0; i--) {
sb = (c >> i) & 1;
setsda(adap, sb);
udelay((adap->udelay + 1) / 2);
if (sclhi(adap) < 0) { /* timed out */
bit_dbg(1, &i2c_adap->dev, "i2c_outb: 0x%02x, "
"timeout at bit #%d\n", (int)c, i);
return -ETIMEDOUT;
}
/* FIXME do arbitration here:
* if (sb && !getsda(adap)) -> ouch! Get out of here.
*
* Report a unique code, so higher level code can retry
* the whole (combined) message and *NOT* issue STOP.
*/
scllo(adap);
}
sdahi(adap);
if (sclhi(adap) < 0) { /* timeout */
bit_dbg(1, &i2c_adap->dev, "i2c_outb: 0x%02x, "
"timeout at ack\n", (int)c);
return -ETIMEDOUT;
}
/* read ack: SDA should be pulled down by slave, or it may
* NAK (usually to report problems with the data we wrote).
*/
ack = !getsda(adap); /* ack: sda is pulled low -> success */
bit_dbg(2, &i2c_adap->dev, "i2c_outb: 0x%02x %s\n", (int)c,
ack ? "A" : "NA");
scllo(adap);
return ack;
/* assert: scl is low (sda undef) */
}
然后根据if (pmsg->flags & I2C_M_RD)这个来判断是发送数据，还是接收数据。
如果是接收数据，那么
ret = readbytes(i2c_adap, pmsg);
static int readbytes(struct i2c_adapter *i2c_adap, struct i2c_msg *msg)
{
int inval;
int rdcount = 0; /* counts bytes read */
unsigned char *temp = msg->buf;
int count = msg->len;
const unsigned flags = msg->flags;
while (count > 0) {
inval = i2c_inb(i2c_adap);
if (inval >= 0) {
*temp = inval;
rdcount++;
} else { /* read timed out */
break;
}
temp++;
count--;
/* Some SMBus transactions require that we receive the
transaction length as the first read byte. */
if (rdcount == 1 && (flags & I2C_M_RECV_LEN)) {
if (inval <= 0 || inval > I2C_SMBUS_BLOCK_MAX) {
if (!(flags & I2C_M_NO_RD_ACK))
acknak(i2c_adap, 0);
dev_err(&i2c_adap->dev, "readbytes: invalid "
"block length (%d)\n", inval);
return -EREMOTEIO;
}
/* The original count value accounts for the extra
bytes, that is, either 1 for a regular transaction,
or 2 for a PEC transaction. */
count += inval;
msg->len += inval;
}
bit_dbg(2, &i2c_adap->dev, "readbytes: 0x%02x %s\n",
inval,
(flags & I2C_M_NO_RD_ACK)
? "(no ack/nak)"
: (count ? "A" : "NA"));
if (!(flags & I2C_M_NO_RD_ACK)) {
inval = acknak(i2c_adap, count);
if (inval < 0)
return inval;
}
}
return rdcount;
}
然后通过这个inval = i2c_inb(i2c_adap);
static int i2c_inb(struct i2c_adapter *i2c_adap)
{
/* read byte via i2c port, without start/stop sequence */
/* acknowledge is sent in i2c_read. */
int i;
unsigned char indata = 0;
struct i2c_algo_bit_data *adap = i2c_adap->algo_data;
/* assert: scl is low */
sdahi(adap);
for (i = 0; i < 8; i++) {
if (sclhi(adap) < 0) { /* timeout */
bit_dbg(1, &i2c_adap->dev, "i2c_inb: timeout at bit "
"#%d\n", 7 - i);
return -ETIMEDOUT;
}
indata *= 2;
if (getsda(adap))
indata |= 0x01;
setscl(adap, 0);
udelay(i == 7 ? adap->udelay / 2 : adap->udelay);
}
/* assert: scl is low */
return indata;
}
这样就把数据接收到了。
如果是发送数据的话，那么就是ret = sendbytes(i2c_adap, pmsg);
static int sendbytes(struct i2c_adapter *i2c_adap, struct i2c_msg *msg)
{
const unsigned char *temp = msg->buf;
int count = msg->len;
unsigned short nak_ok = msg->flags & I2C_M_IGNORE_NAK;
int retval;
int wrcount = 0;
while (count > 0) {
retval = i2c_outb(i2c_adap, *temp);
/* OK/ACK; or ignored NAK */
if ((retval > 0) || (nak_ok && (retval == 0))) {
count--;
temp++;
wrcount++;
/* A slave NAKing the master means the slave didn't like
* something about the data it saw. For example, maybe
* the SMBus PEC was wrong.
*/
} else if (retval == 0) {
dev_err(&i2c_adap->dev, "sendbytes: NAK bailout.\n");
return -EIO;
/* Timeout; or (someday) lost arbitration
*
* FIXME Lost ARB implies retrying the transaction from
* the first message, after the "winning" master issues
* its STOP. As a rule, upper layer code has no reason
* to know or care about this ... it is *NOT* an error.
*/
} else {
dev_err(&i2c_adap->dev, "sendbytes: error %d\n",
retval);
return retval;
}
}
return wrcount;
}
然后通过retval = i2c_outb(i2c_adap, *temp);
发送出给从机。
最后
i2c_stop(adap);
数据发送完了
static void i2c_stop(struct i2c_algo_bit_data *adap)
{
/* assert: scl is low */
sdalo(adap);
sclhi(adap);
setsda(adap, 1);
udelay(adap->udelay);
}
好了，整个gpio模拟的i2c的数据流程就是这样了。具体的很多细节都没有分析，可以通过细读代码来理解。