启动内核出现：start kernel...

  

（一）出现如下错误启动信息

——————————————

U-Boot 1.3.4 (Jun 30 2011 - 09:01:15) for SMDK2416


CPU:   S3C2416@400MHz
       Fclk = 800MHz, Hclk = 133MHz, Pclk = 66MHz
Board: SMDK2416 Mobile DDR
DRAM:    64 MB
Flash:   1 MB
NAND:    128 MB
*** Warning - bad CRC or NAND, using default environment

In:      serial
Out:     serial
Err:     serial
Hit any key to stop autoboot:  0
SAM2416EDK # dnw
Now, Waiting for DNW to transmit data
SAM2416EDK # resetOK

U-Boot 1.3.4 (Jun 30 2011 - 09:01:15) for SMDK2416


CPU:   S3C2416@400MHz
       Fclk = 800MHz, Hclk = 133MHz, Pclk = 66MHz
Board: SMDK2416 Mobile DDR
DRAM:    64 MB
Flash:   1 MB
NAND:    128 MB
*** Warning - bad CRC or NAND, using default environment

In:      serial
Out:     serial
Err:     serial
Hit any key to stop autoboot:  0

NAND read: device 0 offset 0x40000, size 0x1c0000
 1835008 bytes read: OK
Boot with zImage

Starting kernel ...

Uncompressing Linux.............................................................
................................ done, booting the kernel.

U-Boot 1.3.4 (Jun 30 2011 - 09:01:15) for SMDK2416 CPU: S3C2416@400MHz Fclk = 800MHz, Hclk = 133MHz, Pclk = 66MHz Board: SMDK2416 Mobile DDR DRAM: 64 MB Flash: 1 MB NAND: 128 MB *** Warning - bad CRC or NAND, using default environment In: serial Out: serial Err: serial Hit any key to stop autoboot: 0 SAM2416EDK # dnw Now, Waiting for DNW to transmit data SAM2416EDK # resetOK U-Boot 1.3.4 (Jun 30 2011 - 09:01:15) for SMDK2416 CPU: S3C2416@400MHz Fclk = 800MHz, Hclk = 133MHz, Pclk = 66MHz Board: SMDK2416 Mobile DDR DRAM: 64 MB Flash: 1 MB NAND: 128 MB *** Warning - bad CRC or NAND, using default environment In: serial Out: serial Err: serial Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x40000, size 0x1c0000 1835008 bytes read: OK Boot with zImage Starting kernel ... Uncompressing Linux............................................................. ................................ done, booting the kernel.

解决方法：修改flash分区信息

 

——————————————————————————————————————

先不纠结了，直接跳吧。往后也许会再遇到这个问题，或者辅助问题，或者明师益友

——————————————————————————————————————

再坚持了一把，终于内核移植成功。版本匹配问题，smdk最小板功能，重新解压再试一遍，这些很基本的方法在穷途末路时有时会有柳暗花明的效果。哈哈！

但之前我出错的根本原因我还是不知道，连自己怎么成功的都不知道，真惨。反思，反思，一定要找到。。。

原文出处：http://blog.csdn.net/YEYUANGEN/article/details/6693781