microstation level2 0301

1、key-in 快捷键编辑

Setting--AccuDraw--Display选项卡

1、避免命名冲突

2、使用字母和数字组合

3、不要覆盖标准的shortcut名称

4、简写后面设置空格

AccuDraw快捷键的配置文本：

C:\Users\Administrator\AppData\Local\Bentley\MicroStation\8.11\zpi_w6y9sacSIZ7ki0L1ug\shortcut.txt

Enter	"Smart Lock"	"AccuDraw Lock Smart"
Space	"Change Mode"	"AccuDraw Mode"
O	"Set Origin"	"AccuDraw SetOrigin"
V	"View Rotation"	"AccuDraw Rotate View"
T	"Top Rotation"	"AccuDraw Rotate Top"
F	"Front Rotation"	"AccuDraw Rotate Front"	3D
S	"Side Rotation"	"AccuDraw Rotate Side"	3D
B	"Base Rotation"	"AccuDraw Rotate Base Toggle"
E	"Cycle Rotation"	"AccuDraw Rotate Cycle"	3D
X	"Lock X"	"AccuDraw Lock X"
Y	"Lock Y"	"AccuDraw Lock Y"
Z	"Lock Z"	"AccuDraw Lock Z"	3D
D	"Lock Distance"	"AccuDraw Lock Distance"
A	"Lock Angle"	"AccuDraw Lock Angle"
LI	"Lock Index"	"AccuDraw Lock Index"
LC	"Draw line"	"place line constrained"
LP	"Lock ACS Grid Plane"	"AccuDraw Lock GridPlane"	3D
LA	"Lock ACS Plane"	"Lock ACSContext Toggle"	3D
LS	"Lock ACS Plane Snap"	"Lock Snap Construction Toggle"	3D
LZ	"Lock Sticky Z"	"AccuDraw Lock StickyZ"	3D
RQ	"Rotate Quick"	"AccuDraw Rotate Quick"
RA	"Rotate ACS"	"AccuDraw Rotate ACS"
RC	"Rotate to Current ACS"	"AccuDraw Rotate CurrentACS"
RE	"Rotate Element"	"AccuDraw Rotate Element"
RV	"Rotate View"	"AccuDraw Rotate OrientView"
RX	"Rotate about X"	"AccuDraw Rotate X"	3D
RY	"Rotate about Y"	"AccuDraw Rotate Y"	3D
RZ	"Rotate about Z"	"AccuDraw Rotate Z"
?	"Show Shortcuts"	"AccuDraw Dialog Shortcuts"
~	"Bump Tool Setting"	"AccuDraw Bump ToolSetting"
GT	"Go to Tool Settings"	"Dialog ToolSetting"
GK	"Go to Keyin"	"Dialog CmdBrowse"
GS	"Go to Settings"	"AccuDraw Dialog Settings"
GA	"Get ACS"	"AccuDraw Dialog GetACS"
WA	"Write to ACS"	"AccuDraw Dialog SaveACS"
P	"Point Keyin (single)"	"Point Keyin Single"
M	"Point Keyin (multi)"	"Point Keyin Multiple"
I	"Intersect Snap"	"Snap Intersect"
N	"Nearest Snap"	"Snap Nearest"
C	"Center Snap"	"Snap Center"
K	"Snap Divisor"	"AccuDraw Dialog SnapDivisor"
HA	"AccuDraw on Hold"	"AccuDraw Toggle"
HS	"AccuSnap Toggle"	"AccuSnap Toggle"
HU	"AccuSnap Suspend"	"AccuSnap Suspend"
Q	"Quit AccuDraw"	"Accudraw Quit"

但是如果将LC中的命令改成 place circle center constrained，需要调用key-in，输入accudraw shortcuts readfile,重新加载配置文件