i2c drivers

 

Linux设备驱动程序架构分析之一个I2C驱动实例

 

转载于：http://blog.csdn.net/liuhaoyutz

内核版本：3.10.1

编写一个I2C设备驱动程序的工作可分为两部分，一是定义和注册I2C设备，即i2c_client；二是定义和注册I2C设备驱动，即i2c_driver。下面我们就以mini2440的I2C设备at24c08 EEPROM为例，介绍如何完成这两个工作。

 

一、定义和注册I2C设备

步骤1：用i2c_board_info保存I2C设备相关信息

在Linux中，struct i2c_client代表一个I2C设备，该结构体定义在include/linux/i2c.h文件中：

 

200/**
201 * struct i2c_client - represent an I2Cslave device
202 * @flags: I2C_CLIENT_TEN indicates thedevice uses a ten bit chip address;
203 * I2C_CLIENT_PEC indicates it uses SMBus Packet Error Checking
204 * @addr: Address used on the I2C busconnected to the parent adapter.
205 * @name: Indicates the type of thedevice, usually a chip name that's
206 * generic enough to hide second-sourcing and compatible revisions.
207 * @adapter: manages the bus segmenthosting this I2C device
208 * @driver: device's driver, hencepointer to access routines
209 * @dev: Driver model device node forthe slave.
210 * @irq: indicates the IRQ generated bythis device (if any)
211 * @detected: member of ani2c_driver.clients list or i2c-core's
212 * userspace_devices list
213 *
214 * An i2c_client identifies a singledevice (i.e. chip) connected to an
215 * i2c bus. The behaviour exposed to Linuxis defined by the driver
216 * managing the device.
217 */
218struct i2c_client {
219   unsigned short flags;       /*div., see below      */
220   unsigned short addr;        /*chip address - NOTE: 7bit    */
221                    /* addresses are stored inthe  */
222                    /* _LOWER_ 7 bits       */
223   char name[I2C_NAME_SIZE];
224   struct i2c_adapter *adapter;    /*the adapter we sit on    */
225   struct i2c_driver *driver;  /* andour access routines  */
226   struct device dev;      /* thedevice structure     */
227   int irq;            /* irq issuedby device     */
228   struct list_head detected;
229};

 

我们不用直接定义一个i2c_client结构，Linux会根据I2C设备的相关信息自动创建i2c_client。所以，我们需要提供I2C设备的相关信息。对于Mini2440的I2C设备at24c08 EEPROM，其相关信息保存在arch/arm/mach-s3c24xx/mach-mini2440.c文件中：

 

485/*
486 * I2C devices
487 */
488static struct at24_platform_data at24c08= {
489   .byte_len   = SZ_8K / 8,
490   .page_size  = 16,
491};
492
493static struct i2c_board_infomini2440_i2c_devs[] __initdata = {
494   {
495       I2C_BOARD_INFO("24c08", 0x50),
496       .platform_data = &at24c08,
497   },
498};

 

struct i2c_board_info是创建i2c设备的模板，该结构体定义在include/linux/i2c.h文件中：

 

251/**
252 * struct i2c_board_info - template fordevice creation
253 * @type: chip type, to initializei2c_client.name
254 * @flags: to initializei2c_client.flags
255 * @addr: stored in i2c_client.addr
256 * @platform_data: stored ini2c_client.dev.platform_data
257 * @archdata: copied intoi2c_client.dev.archdata
258 * @of_node: pointer to OpenFirmwaredevice node
259 * @acpi_node: ACPI device node
260 * @irq: stored in i2c_client.irq
261 *
262 * I2C doesn't actually support hardwareprobing, although controllers and
263 * devices may be able to useI2C_SMBUS_QUICK to tell whether or not there's
264 * a device at a given address.  Drivers commonly need more information than
265 * that, such as chip type,configuration, associated IRQ, and so on.
266 *
267 * i2c_board_info is used to buildtables of information listing I2C devices
268 * that are present.  This information is used to grow the drivermodel tree.
269 * For mainboards this is donestatically using i2c_register_board_info();
270 * bus numbers identify adapters thataren't yet available.  For add-on boards,
271 * i2c_new_device() does thisdynamically with the adapter already known.
272 */
273struct i2c_board_info {
274   char        type[I2C_NAME_SIZE];
275   unsigned short  flags;
276   unsigned short  addr;
277   void        *platform_data;
278   struct dev_archdata *archdata;
279   struct device_node *of_node;
280   struct acpi_dev_node acpi_node;
281   int     irq;
282};

 

从注释可以看到，i2c_board_info结构体用来保存I2C设备的相关信息，Linux根据这些信息创建I2C设备相关的设备模型树。对于mainboards，通过调用i2c_register_board_info()静态完成。对于add-on boards，通过调用i2c_new_device()动态完成。

i2c_board_info结构体有两个成员必须初始化，一个是type，用来初始化i2c_client.name；另一个是addr，用来初始化i2c_client.addr。其它i2c_board_info结构体成员根据需要赋值或保持为空。

宏I2C_BOARD_INFO定义在include/linux/i2c.h文件中，其内容如下：

 

284/**
285 * I2C_BOARD_INFO - macro used to listan i2c device and its address
286 * @dev_type: identifies the device type
287 * @dev_addr: the device's address onthe bus.
288 *
289 * This macro initializes essentialfields of a struct i2c_board_info,
290 * declaring what has been provided on aparticular board.  Optional
291 * fields (such as associated irq, ordevice-specific platform_data)
292 * are provided using conventionalsyntax.
293 */
294#define I2C_BOARD_INFO(dev_type,dev_addr) \
295   .type = dev_type, .addr = (dev_addr)

 

从注释可以看到，I2C_BOARD_INFO宏用来初始化i2c_board_info结构体的两个必须初始化的成员变量type和addr。i2c_board_info结构体的其它成员变量使用常规的初始化语法。

struct at24_platform_data定义在include/linux/i2c/at24.h文件中：

1

4/**
15 * struct at24_platform_data - data toset up at24 (generic eeprom) driver
16 * @byte_len: size of eeprom in byte
17 * @page_size: number of byte which canbe written in one go
18 * @flags: tunable options, checkAT24_FLAG_* defines
19 * @setup: an optional callback invokedafter eeprom is probed; enables kernel
20   code to access eeprom via memory_accessor, see example
21 * @context: optional parameter passed tosetup()
22 *
23 * If you set up a custom eeprom type,please double-check the parameters.
24 * Especially page_size needs extra care,as you risk data loss if your value
25 * is bigger than what the chip actuallysupports!
26 *
27 * An example in pseudo code for asetup() callback:
28 *
29 * void get_mac_addr(structmemory_accessor *mem_acc, void *context)
30 * {
31 * u8 *mac_addr = ethernet_pdata->mac_addr;
32 * off_t offset = context;
33 *
34 * // Read MAC addr from EEPROM
35 * if (mem_acc->read(mem_acc, mac_addr, offset, ETH_ALEN) == ETH_ALEN)
36 *     pr_info("Read MAC addr from EEPROM: %pM\n", mac_addr);
37 * }
38 *
39 * This function pointer and context cannow be set up in at24_platform_data.
40 */
41
42struct at24_platform_data {
43   u32     byte_len;       /* size (sum of all addr) */
44   u16     page_size;      /* for writes */
45   u8      flags;
46#define AT24_FLAG_ADDR16    0x80   /* address pointer is 16 bit */
47#define AT24_FLAG_READONLY  0x40   /* sysfs-entry will be read-only */
48#define AT24_FLAG_IRUGO     0x20   /* sysfs-entry will be world-readable */
49#define AT24_FLAG_TAKE8ADDR 0x10    /* take always 8 addresses (24c00) */
50
51   void        (*setup)(structmemory_accessor *, void *context);
52   void        *context;
53};

 

该结构体用来保存at24系列EEPROM的platform data。byte_len成员变量保存EEPROM的大小，以byte为单位。page_size成员变量用来指定一次最多能写多少个byte。对于Mini2440，定义at24_platform_data结构体变量at24c08：

 

488static struct at24_platform_data at24c08= {
489   .byte_len   = SZ_8K / 8,
490   .page_size  = 16,
491};

 

SZ_8K宏即8K，定义在include/linux/sizes.h文件中：

 

25#define SZ_8K               0x00002000

 

 

步骤2：调用i2c_register_board_info注册i2c设备相关信息

对于Mini2440的I2C设备at24c08 EEPROM，由arch/arm/mach-s3c24xx/mach-mini2440.c文件中的mini2440_init函数调用i2c_register_board_info注册i2c设备相关信息，mini2440_init函数内容如下：

 

622static void __init mini2440_init(void)
623{
624   struct mini2440_features_t features = { 0 };
625   int i;
626
627   printk(KERN_INFO "MINI2440: Option string mini2440=%s\n",
628            mini2440_features_str);
629
630   /* Parse the feature string */
631   mini2440_parse_features(&features, mini2440_features_str);
632
633   /* turn LCD on */
634   s3c_gpio_cfgpin(S3C2410_GPC(0), S3C2410_GPC0_LEND);
635
636   /* Turn the backlight early on */
637   WARN_ON(gpio_request_one(S3C2410_GPG(4), GPIOF_OUT_INIT_HIGH, NULL));
638   gpio_free(S3C2410_GPG(4));
639
640   /* remove pullup on optional PWM backlight -- unused on 3.5 and 7"s*/
641   gpio_request_one(S3C2410_GPB(1), GPIOF_IN, NULL);
642   s3c_gpio_setpull(S3C2410_GPB(1), S3C_GPIO_PULL_UP);
643   gpio_free(S3C2410_GPB(1));
644
645   /* mark the key as input, without pullups (there is one on the board) */
646   for (i = 0; i < ARRAY_SIZE(mini2440_buttons); i++) {
647       s3c_gpio_setpull(mini2440_buttons[i].gpio, S3C_GPIO_PULL_UP);
648       s3c_gpio_cfgpin(mini2440_buttons[i].gpio, S3C2410_GPIO_INPUT);
649   }
650   if (features.lcd_index != -1) {
651       int li;
652
653       mini2440_fb_info.displays =
654           &mini2440_lcd_cfg[features.lcd_index];
655
656       printk(KERN_INFO "MINI2440: LCD");
657       for (li = 0; li < ARRAY_SIZE(mini2440_lcd_cfg); li++)
658            if (li == features.lcd_index)
659                printk(" [%d:%dx%d]",li,
660                   mini2440_lcd_cfg[li].width,
661                   mini2440_lcd_cfg[li].height);
662            else
663                printk(" %d:%dx%d",li,
664                    mini2440_lcd_cfg[li].width,
665                    mini2440_lcd_cfg[li].height);
666       printk("\n");
667       s3c24xx_fb_set_platdata(&mini2440_fb_info);
668   }
669
670   s3c24xx_udc_set_platdata(&mini2440_udc_cfg);
671   s3c24xx_mci_set_platdata(&mini2440_mmc_cfg);
672   s3c_nand_set_platdata(&mini2440_nand_info);
673   s3c_i2c0_set_platdata(NULL);
674
675   i2c_register_board_info(0, mini2440_i2c_devs,
676                ARRAY_SIZE(mini2440_i2c_devs));
677
678   platform_add_devices(mini2440_devices, ARRAY_SIZE(mini2440_devices));
679
680   if (features.count) /* the optional features */
681       platform_add_devices(features.optional, features.count);
682
683}

 

这个函数我们这里只需要关注675行，调用i2c_register_board_info注册mini2440_i2c_devs。mini2440_i2c_devs就是上面定义的i2c_board_info结构体数组，其中定义了at24c08相关信息。

i2c_register_board_info函数定义在drivers/i2c/i2c-boardinfo.c文件中，其内容如下：

 

42/**
43 * i2c_register_board_info - staticallydeclare I2C devices
44 * @busnum: identifies the bus to whichthese devices belong
45 * @info: vector of i2c devicedescriptors
46 * @len: how many descriptors in the vector;may be zero to reserve
47 * the specified bus number.
48 *
49 * Systems using the Linux I2C driverstack can declare tables of board info
50 * while they initialize.  This should be done in board-specific initcode
51 * near arch_initcall() time, orequivalent, before any I2C adapter driver is
52 * registered.  For example, mainboard init code could defineseveral devices,
53 * as could the init code for eachdaughtercard in a board stack.
54 *
55 * The I2C devices will be created later,after the adapter for the relevant
56 * bus has been registered.  After that moment, standard driver modeltools
57 * are used to bind "new style"I2C drivers to the devices.  The busnumber
58 * for any device declared using thisroutine is not available for dynamic
59 * allocation.
60 *
61 * The board info passed can safely be__initdata, but be careful of embedded
62 * pointers (for platform_data,functions, etc) since that won't be copied.
63 */
64int __init
65i2c_register_board_info(int busnum,
66   struct i2c_board_info const *info, unsigned len)
67{
68   int status;
69
70   down_write(&__i2c_board_lock);
71
72   /* dynamic bus numbers will be assigned after the last static one */
73   if (busnum >= __i2c_first_dynamic_bus_num)
74       __i2c_first_dynamic_bus_num = busnum + 1;
75
76   for (status = 0; len; len--, info++) {
77       struct i2c_devinfo  *devinfo;
78
79       devinfo = kzalloc(sizeof(*devinfo), GFP_KERNEL);
80       if (!devinfo) {
81            pr_debug("i2c-core: can'tregister boardinfo!\n");
82            status = -ENOMEM;
83            break;
84       }
85
86       devinfo->busnum = busnum;
87       devinfo->board_info = *info;
88       list_add_tail(&devinfo->list, &__i2c_board_list);
89   }
90
91   up_write(&__i2c_board_lock);
92
93   return status;
94}

 

第一个参数busnum表明I2C设备所依附的I2C总线的总线号。

72-74行，如果参数传递进来的busnum 大于等于__i2c_first_dynamic_bus_num，则将__i2c_first_dynamic_bus_num设置为busnum+1。__i2c_first_dynamic_bus_num代表第一个动态分配的I2C总线号，所以，动态分配的I2C总线号总是大于静态分配的I2C总线号。

__i2c_first_dynamic_bus_num定义在drivers/i2c/i2c-boardinfo.c文件中：

 

38int __i2c_first_dynamic_bus_num;

 

因为__i2c_first_dynamic_bus_num是一个全局变量，所以其值被自动初始化为0。所以73行的if判断是成立的。

76-89行，循环遍历info数组，用i2c_board_info变量初始化structi2c_devinfo指针变量devinfo，然后将devinfo放入__i2c_board_list链表中。

i2c_devinfo变量定义在drivers/i2c/i2c-core.h文件中：

 

22struct i2c_devinfo {
23   struct list_head    list;
24   int         busnum;
25   struct i2c_board_info  board_info;
26};

 

可以看到i2c_devinfo结构体只有三个成员变量，busnum用来保存I2C设备所依附的I2C总线号。board_info用来保存I2C设备相关信息。list用于链接到全局链表__i2c_board_list中。

__i2c_board_list 链表定义在drivers/i2c/i2c-boardinfo.c文件中：

 

35LIST_HEAD(__i2c_board_list);
36EXPORT_SYMBOL_GPL(__i2c_board_list);

 

全局变量__i2c_board_list上挂载着所有的I2C设备的信息，包括I2C设备所在的I2C总线的总线号。

所以，i2c_register_board_info函数并没有创建i2c_client，只是将i2c_devinfo变量放入__i2c_board_list链表中。那么，什么时候才会创建i2c_client呢？这个就与创建I2C设备驱动程序无关了，而是跟I2C adapter驱动程序有关：

注册一个I2C adapter有两种方法，一是调用i2c_add_adapter函数，二是调用i2c_add_numbered_adapter函数。

先来看i2c_add_adapter函数，它定义在drivers/i2c/i2c-core.c文件中：

 

1099/**
1100 * i2c_add_adapter - declare i2cadapter, use dynamic bus number
1101 * @adapter: the adapter to add
1102 * Context: can sleep
1103 *
1104 * This routine is used to declare anI2C adapter when its bus number
1105 * doesn't matter or when its busnumber is specified by an dt alias.
1106 * Examples of bases when the busnumber doesn't matter: I2C adapters
1107 * dynamically added by USB links orPCI plugin cards.
1108 *
1109 * When this returns zero, a new busnumber was allocated and stored
1110 * in adap->nr, and the specifiedadapter became available for clients.
1111 * Otherwise, a negative errno value isreturned.
1112 */
1113int i2c_add_adapter(struct i2c_adapter*adapter)
1114{
1115   struct device *dev = &adapter->dev;
1116   int id;
1117
1118   if (dev->of_node) {
1119       id = of_alias_get_id(dev->of_node, "i2c");
1120       if (id >= 0) {
1121            adapter->nr = id;
1122            return__i2c_add_numbered_adapter(adapter);
1123       }
1124   }
1125
1126   mutex_lock(&core_lock);
1127   id = idr_alloc(&i2c_adapter_idr, adapter,
1128               __i2c_first_dynamic_bus_num, 0,GFP_KERNEL);
1129   mutex_unlock(&core_lock);
1130   if (id < 0)
1131       return id;
1132
1133   adapter->nr = id;
1134
1135   return i2c_register_adapter(adapter);
1136}

 

该函数为参数指定的i2c_adapter动态分配的个I2C总线号，并注册该i2c_adapter。

1118-1124行，忽略。

1127-1133行，调用idr_alloc，动态分配一个id号，并将该id号做为i2c_adapter的I2C总线号。

关于idr机制，我们不详细分析，只需要知道它是一种快速索引机制，它将一个整数ID与一个需要被索引的指针建立联系，方便进行查找。例如，这里idr_alloc返回的id与i2c_adapter建立了索引。idr_alloc的第三个参数指定返回ID的最小值（闭区间），第四个参数指定返回ID的最大值（开区间），即idr_alloc返回的ID大于等于第三个参数，而且必须小于第四个参数。在这个函数中，第三个参数为__i2c_first_dynamic_bus_num，所以返回的id必然是大于等于__i2c_first_dynamic_bus_num的，即动态分配的I2C总线号必然大于__i2c_first_dynamic_bus_num。

1135行，调用i2c_register_adapter注册i2c_adapter。

下面我们来看i2c_add_numbered_adapter，该函数定义在drivers/i2c/i2c-core.c文件中：

 

1139/**
1140 * i2c_add_numbered_adapter - declarei2c adapter, use static bus number
1141 * @adap: the adapter to register (withadap->nr initialized)
1142 * Context: can sleep
1143 *
1144 * This routine is used to declare anI2C adapter when its bus number
1145 * matters.  For example, use it for I2C adapters fromsystem-on-chip CPUs,
1146 * or otherwise built in to thesystem's mainboard, and where i2c_board_info
1147 * is used to properly configure I2Cdevices.
1148 *
1149 * If the requested bus number is setto -1, then this function will behave
1150 * identically to i2c_add_adapter, andwill dynamically assign a bus number.
1151 *
1152 * If no devices have pre-been declaredfor this bus, then be sure to
1153 * register the adapter before anydynamically allocated ones.  Otherwise
1154 * the required bus ID may not beavailable.
1155 *
1156 * When this returns zero, thespecified adapter became available for
1157 * clients using the bus numberprovided in adap->nr.  Also, the table
1158 * of I2C devices pre-declared usingi2c_register_board_info() is scanned,
1159 * and the appropriate driver modeldevice nodes are created.  Otherwise, a
1160 * negative errno value is returned.
1161 */
1162int i2c_add_numbered_adapter(structi2c_adapter *adap)
1163{
1164   if (adap->nr == -1) /* -1 means dynamically assign bus id */
1165       return i2c_add_adapter(adap);
1166
1167   return __i2c_add_numbered_adapter(adap);
1168}

 

该函数用于注册参数指定的i2c_adapter，该i2c_adapter的I2C总线号即i2c_adapter.nr必须已经静态设置好了。如果adap->nr为-1，则调用i2c_add_adapter动态分配I2C总线号，再注册。否则，调用__i2c_add_numbered_adapter函数。

__i2c_add_numbered_adapter函数定义在drivers/i2c/i2c-core.c文件中：

 

1078/**
1079 * __i2c_add_numbered_adapter -i2c_add_numbered_adapter where nr is never -1
1080 * @adap: the adapter to register (withadap->nr initialized)
1081 * Context: can sleep
1082 *
1083 * See i2c_add_numbered_adapter() fordetails.
1084 */
1085static int__i2c_add_numbered_adapter(struct i2c_adapter *adap)
1086{
1087   int id;
1088
1089   mutex_lock(&core_lock);
1090   id = idr_alloc(&i2c_adapter_idr, adap, adap->nr, adap->nr + 1,
1091               GFP_KERNEL);
1092   mutex_unlock(&core_lock);
1093   if (id < 0)
1094       return id == -ENOSPC ? -EBUSY : id;
1095
1096   return i2c_register_adapter(adap);
1097}

 

1090-1091行，调用idr_alloc函数，建立idr索引关系。返回的id必须大于等于第三个参数adap->nr，同时必须小于第四个参数adap->nr+1，所以返回的id必然等于adap->nr，即静态指定的I2C总线号。

1096行，调用i2c_register_adapter注册i2c_adapter。

到这里，我们就知道了注册一个i2c_adapter可以调用i2c_add_numbered_adapter函数静态指定一个I2C总线号，也可以调用i2c_add_adapter函数动态分配一个I2C总线号。但是不论哪种方法，最后的注册工作都必须通过调用i2c_register_adapter函数完成。

i2c_register_adapter函数定义在drivers/i2c/i2c-core.c文件中，其内容如下：

 

 980staticint i2c_register_adapter(struct i2c_adapter *adap)
 981{
 982   int res = 0;
 983
 984   /* Can't register until after driver model init */
 985   if (unlikely(WARN_ON(!i2c_bus_type.p))) {
 986       res = -EAGAIN;
 987       goto out_list;
 988    }
 989
 990   /* Sanity checks */
 991   if (unlikely(adap->name[0] == '\0')) {
 992       pr_err("i2c-core: Attempt to register an adapter with "
 993               "no name!\n");
 994       return -EINVAL;
 995    }
 996   if (unlikely(!adap->algo)) {
 997       pr_err("i2c-core: Attempt to register adapter '%s' with "
 998               "no algo!\n",adap->name);
 999       return -EINVAL;
1000   }
1001
1002   rt_mutex_init(&adap->bus_lock);
1003   mutex_init(&adap->userspace_clients_lock);
1004   INIT_LIST_HEAD(&adap->userspace_clients);
1005
1006   /* Set default timeout to 1 second if not already set */
1007   if (adap->timeout == 0)
1008       adap->timeout = HZ;
1009
1010   dev_set_name(&adap->dev, "i2c-%d", adap->nr);
1011   adap->dev.bus = &i2c_bus_type;
1012   adap->dev.type = &i2c_adapter_type;
1013   res = device_register(&adap->dev);
1014   if (res)
1015       goto out_list;
1016
1017   dev_dbg(&adap->dev, "adapter [%s] registered\n",adap->name);
1018
1019#ifdef CONFIG_I2C_COMPAT
1020   res = class_compat_create_link(i2c_adapter_compat_class,&adap->dev,
1021                       adap->dev.parent);
1022   if (res)
1023       dev_warn(&adap->dev,
1024             "Failed to createcompatibility class link\n");
1025#endif
1026
1027   /* bus recovery specific initialization */
1028   if (adap->bus_recovery_info) {
1029       struct i2c_bus_recovery_info*bri = adap->bus_recovery_info;
1030
1031       if (!bri->recover_bus) {
1032            dev_err(&adap->dev, "Norecover_bus() found, not using recovery\n");
1033            adap->bus_recovery_info = NULL;
1034            goto exit_recovery;
1035       }
1036
1037       /* Generic GPIO recovery */
1038       if (bri->recover_bus == i2c_generic_gpio_recovery) {
1039            if(!gpio_is_valid(bri->scl_gpio)) {
1040                dev_err(&adap->dev,"Invalid SCL gpio, not using recovery\n");
1041                adap->bus_recovery_info =NULL;
1042                goto exit_recovery;
1043            }
1044
1045            if(gpio_is_valid(bri->sda_gpio))
1046                bri->get_sda =get_sda_gpio_value;
1047           else
1048                bri->get_sda = NULL;
1049
1050            bri->get_scl =get_scl_gpio_value;
1051            bri->set_scl =set_scl_gpio_value;
1052       } else if (!bri->set_scl || !bri->get_scl) {
1053            /* Generic SCL recovery */
1054            dev_err(&adap->dev, "No{get|set}_gpio() found, not using recovery\n");
1055            adap->bus_recovery_info = NULL;
1056       }
1057   }
1058
1059exit_recovery:
1060   /* create pre-declared device nodes */
1061   if (adap->nr < __i2c_first_dynamic_bus_num)
1062       i2c_scan_static_board_info(adap);
1063
1064   /* Notify drivers */
1065   mutex_lock(&core_lock);
1066   bus_for_each_drv(&i2c_bus_type, NULL, adap, __process_new_adapter);
1067   mutex_unlock(&core_lock);
1068
1069   return 0;
1070
1071out_list:
1072   mutex_lock(&core_lock);
1073   idr_remove(&i2c_adapter_idr, adap->nr);
1074   mutex_unlock(&core_lock);
1075   return res;
1076}

 

984-1000行，做一些必要的检查工作。

1002-1008行，做一些简单的i2c_adapter成员变量初始化工作。

1010-1013行，初始化i2c_adapter.dev，并调用device_register注册i2c_adapter.dev。

1028-1057行，I2C总线恢复时相关的初始化工作。

1060-1062行，因为动态分析的I2C总线号必须大于或等于__i2c_first_dynamic_bus_num，所以，如果adap->nr< __i2c_first_dynamic_bus_num，说明是静态指定的I2C总线号，此时，要调用i2c_scan_static_board_info函数探测I2C总线上静态注册的I2C设备。

i2c_scan_static_board_info函数定义在drivers/i2c/i2c-core.c文件中，其内容如下：

 

941staticvoid i2c_scan_static_board_info(struct i2c_adapter *adapter)
942{
943   struct i2c_devinfo  *devinfo;
944
945   down_read(&__i2c_board_lock);
946   list_for_each_entry(devinfo, &__i2c_board_list, list) {
947       if (devinfo->busnum == adapter->nr
948                &&!i2c_new_device(adapter,
949                       &devinfo->board_info))
950           dev_err(&adapter->dev,
951                "Can't create device at0x%02x\n",
952                devinfo->board_info.addr);
953    }
954   up_read(&__i2c_board_lock);
955}

 

946-953行，遍历__i2c_board_list链表，如果devinfo->busnum等于adapter->nr，即链表节点所代表的I2C设备的I2C总线号等于i2c_adapter的I2C总线号，则调用i2c_new_device创建并注册I2C设备对应的i2c_client结构体。

到这里，就和我们在本文开始部分介绍的静态注册的i2c_board_info信息联系起来了。回忆一下我们通过调用i2c_register_board_info函数将将包含所有I2C设备的i2c_board_info信息的i2c_devinfo变量加入到__i2c_board_list链表中。现在在注册i2c_adater时，又通过调用i2c_scan_static_board_info函数遍历__i2c_board_list链表，查找属于对应i2c_adapter的I2C设备，如果找到，调用i2c_new_device创建对应的i2c_client结构体。

i2c_new_device函数定义在drivers/i2c/i2c-core.c文件中，其内容如下：

 

612/**
613* i2c_new_device - instantiate an i2c device
614* @adap: the adapter managing the device
615* @info: describes one I2C device; bus_num is ignored
616* Context: can sleep
617*
618* Create an i2c device. Binding is handled through driver model
619* probe()/remove() methods.  A driver maybe bound to this device when we
620* return from this function, or any later moment (e.g. maybe hotplugging will
621* load the driver module).  This call isnot appropriate for use by mainboard
622* initialization logic, which usually runs during an arch_initcall() long
623* before any i2c_adapter could exist.
624*
625* This returns the new i2c client, which may be saved for later use with
626* i2c_unregister_device(); or NULL to indicate an error.
627*/
628struct i2c_client *
629i2c_new_device(struct i2c_adapter *adap,struct i2c_board_info const *info)
630{
631   struct i2c_client   *client;
632   int         status;
633
634   client = kzalloc(sizeof *client, GFP_KERNEL);
635   if (!client)
636       return NULL;
637
638   client->adapter = adap;
639
640   client->dev.platform_data = info->platform_data;
641
642   if (info->archdata)
643       client->dev.archdata = *info->archdata;
644
645   client->flags = info->flags;
646   client->addr = info->addr;
647   client->irq = info->irq;
648
649   strlcpy(client->name, info->type, sizeof(client->name));
650
651   /* Check for address validity */
652   status = i2c_check_client_addr_validity(client);
653   if (status) {
654        dev_err(&adap->dev,"Invalid %d-bit I2C address 0x%02hx\n",
655            client->flags & I2C_CLIENT_TEN ?10 : 7, client->addr);
656       goto out_err_silent;
657    }
658
659   /* Check for address business */
660   status = i2c_check_addr_busy(adap, client->addr);
661   if (status)
662       goto out_err;
663
664   client->dev.parent = &client->adapter->dev;
665   client->dev.bus = &i2c_bus_type;
666   client->dev.type = &i2c_client_type;
667   client->dev.of_node = info->of_node;
668   ACPI_HANDLE_SET(&client->dev, info->acpi_node.handle);
669
670   /* For 10-bit clients, add an arbitrary offset to avoid collisions */
671   dev_set_name(&client->dev, "%d-%04x",i2c_adapter_id(adap),
672            client->addr | ((client->flags & I2C_CLIENT_TEN)
673                     ? 0xa000 : 0));
674    status =device_register(&client->dev);
675   if (status)
676       goto out_err;
677
678   dev_dbg(&adap->dev, "client [%s] registered with bus id%s\n",
679       client->name, dev_name(&client->dev));
680
681   return client;
682
683out_err:
684   dev_err(&adap->dev, "Failed to register i2c client %s at0x%02x "
685       "(%d)\n", client->name, client->addr, status);
686out_err_silent:
687   kfree(client);
688   return NULL;
689}

 

这个函数根据参数传递进来的信息，创建并注册i2c_client。

634行，为i2c_client变量分配内存空间。

638行，将i2c_client.adapter设置为参数传递进来的i2c_adapter。

640 行，将i2c_client.dev.platform_data设置为 info->platform_data;

645行，将i2c_client.flags设置为info->flags;

646行，将i2c_client.addr设置为info->addr;

647行，将i2c_client.irq设置为info->irq;

649行，将i2c_client.name设置为info->type;

651-657行，检查指定的I2C设备地址是否有效。

660-662行，检查指定的I2C设备地址是否忙。

664-674行，初始化i2c_client.dev，并调用device_register注册i2c_client.dev。

i2c_register_adapter函数我们还有一点内容没有分析完，回到i2c_register_adapter函数，上面我们分析到了1062行的i2c_scan_static_board_info(adap)，只有在adap->nr小于__i2c_first_dynamic_bus_num即静态指定了i2c_adapter的I2C总线号的情况下，才会调用这个函数。对于动态分配I2C总线号的情况，直接跳过。这就说明，只有在静态指定i2c_adapter的I2C总线号的情况下，才会扫描静态注册的I2C设备，如果动态指定i2c_adapter的I2C总线号，不会扫描静态注册的I2C设备。对于I2C驱动程序，这种静态注册的方式，称为new-style driver；而动态探测的方式，称为legacy driver。

下面我们继续分析i2c_register_adapter函数，前面调用i2c_scan_static_board_info实例化了静态注册的I2C设备，下面要完成对I2C设备的动态探测和实例化：

不论是静态指定还是动态分配I2C总线号，都会调用到1066行的bus_for_each_drv函数。

1066行，调用bus_for_each_drv函数，该函数定义在drivers/base/bus.c文件中，其内容如下：

417/**
418 * bus_for_each_drv - driver iterator
419 * @bus: bus we're dealing with.
420 * @start: driver to start iterating on.
421 * @data: data to pass to the callback.
422 * @fn: function to call for each driver.
423 *
424 * This is nearly identical to the device iterator above.
425 * We iterate over each driver that belongs to @bus, and call
426 * @fn for each. If @fn returns anything but 0, we break out
427 * and return it. If @start is not NULL, we use it as the head
428 * of the list.
429 *
430 * NOTE: we don't return the driver that returns a non-zero
431 * value, nor do we leave the reference count incremented for that
432 * driver. If the caller needs to know that info, it must set it
433 * in the callback. It must also be sure to increment the refcount
434 * so it doesn't disappear before returning to the caller.
435 */
436int bus_for_each_drv(struct bus_type *bus, struct device_driver *start,
437             void *data, int (*fn)(struct device_driver *, void *))
438{
439    struct klist_iter i;
440    struct device_driver *drv;
441    int error = 0;
442
443    if (!bus)
444        return -EINVAL;
445
446    klist_iter_init_node(&bus->p->klist_drivers, &i,
447                 start ? &start->p->knode_bus : NULL);
448    while ((drv = next_driver(&i)) && !error)
449        error = fn(drv, data);
450    klist_iter_exit(&i);
451    return error;
452}

这个函数我们在《Linux设备模型分析之device（基于3.10.1内核）》一文中已经分析过了。448-449行，这个while循环依次遍历bus->p->klist_drivers中的所有device_driver，对于每个device_driver，调用fn(drv，data)函数。这里，传递过来的fn参数是__process_new_adapter，data参数是adap。这个循环是一个关键点，注册一个新的i2c_adapter后，要为该i2c_adapter上的i2c设备匹配驱动程序，这个匹配过程就是通过这个循环调用__process_new_adapter函数完成的。

__process_new_adapter函数定义在drivers/i2c/i2c-core.c文件中，其内容如下：

975static int __process_new_adapter(struct device_driver *d, void *data)
976{
977    return i2c_do_add_adapter(to_i2c_driver(d), data);
978}

注意i2c_do_add_adapter函数的第一个参数，从device_driver转换为i2c_driver。

i2c_do_add_adapter函数定义在drivers/i2c/i2c-core.c文件中，其内容如下：

957static int i2c_do_add_adapter(struct i2c_driver *driver,
958                  struct i2c_adapter *adap)
959{
960    /* Detect supported devices on that bus, and instantiate them */
961    i2c_detect(adap, driver);
962
963    /* Let legacy drivers scan this bus for matching devices */
964    if (driver->attach_adapter) {
965        dev_warn(&adap->dev, "%s: attach_adapter method is deprecated\n",
966             driver->driver.name);
967        dev_warn(&adap->dev, "Please use another way to instantiate "
968             "your i2c_client\n");
969        /* We ignore the return code; if it fails, too bad */
970        driver->attach_adapter(adap);
971    }
972    return 0;
973}

961行，调用i2c_detect函数，探测并初始化该i2c总线上的i2c设备。该函数定义在drivers/i2c/i2c-core.c文件中，其内容如下：

1730static int i2c_detect(struct i2c_adapter *adapter, struct i2c_driver *driver)
1731{
1732    const unsigned short *address_list;
1733    struct i2c_client *temp_client;
1734    int i, err = 0;
1735    int adap_id = i2c_adapter_id(adapter);
1736
1737    address_list = driver->address_list;
1738    if (!driver->detect || !address_list)
1739        return 0;
1740
1741    /* Stop here if the classes do not match */
1742    if (!(adapter->class & driver->class))
1743        return 0;
1744
1745    /* Set up a temporary client to help detect callback */
1746    temp_client = kzalloc(sizeof(struct i2c_client), GFP_KERNEL);
1747    if (!temp_client)
1748        return -ENOMEM;
1749    temp_client->adapter = adapter;
1750
1751    for (i = 0; address_list[i] != I2C_CLIENT_END; i += 1) {
1752        dev_dbg(&adapter->dev, "found normal entry for adapter %d, "
1753            "addr 0x%02x\n", adap_id, address_list[i]);
1754        temp_client->addr = address_list[i];
1755        err = i2c_detect_address(temp_client, driver);
1756        if (unlikely(err))
1757            break;
1758    }
1759
1760    kfree(temp_client);
1761    return err;
1762}

1755行，调用i2c_detect_address，探测指定的地址上的I2C设备是否存在，如果存在，注册该i2c设备。i2c_detect_address函数定义在drivers/i2c/i2c-core.c文件中，其内容如下：

1675static int i2c_detect_address(struct i2c_client *temp_client,
1676                  struct i2c_driver *driver)
1677{
1678    struct i2c_board_info info;
1679    struct i2c_adapter *adapter = temp_client->adapter;
1680    int addr = temp_client->addr;
1681    int err;
1682
1683    /* Make sure the address is valid */
1684    err = i2c_check_addr_validity(addr);
1685    if (err) {
1686        dev_warn(&adapter->dev, "Invalid probe address 0x%02x\n",
1687             addr);
1688        return err;
1689    }
1690
1691    /* Skip if already in use */
1692    if (i2c_check_addr_busy(adapter, addr))
1693        return 0;
1694
1695    /* Make sure there is something at this address */
1696    if (!i2c_default_probe(adapter, addr))
1697        return 0;
1698
1699    /* Finally call the custom detection function */
1700    memset(&info, 0, sizeof(struct i2c_board_info));
1701    info.addr = addr;
1702    err = driver->detect(temp_client, &info);
1703    if (err) {
1704        /* -ENODEV is returned if the detection fails. We catch it
1705           here as this isn't an error. */
1706        return err == -ENODEV ? 0 : err;
1707    }
1708
1709    /* Consistency check */
1710    if (info.type[0] == '\0') {
1711        dev_err(&adapter->dev, "%s detection function provided "
1712            "no name for 0x%x\n", driver->driver.name,
1713            addr);
1714    } else {
1715        struct i2c_client *client;
1716
1717        /* Detection succeeded, instantiate the device */
1718        dev_dbg(&adapter->dev, "Creating %s at 0x%02x\n",
1719            info.type, info.addr);
1720        client = i2c_new_device(adapter, &info);
1721        if (client)
1722            list_add_tail(&client->detected, &driver->clients);
1723        else
1724            dev_err(&adapter->dev, "Failed creating %s at 0x%02x\n",
1725                info.type, info.addr);
1726    }
1727    return 0;
1728}

1702行，调用driver->detect。

1720行，如果探测到i2c设备确实存在，调用i2c_new_device函数初始化对应的i2c_client结构体并注册。i2c_new_device函数我们在前面已经分析过。

至此，i2c_adapter的注册过程我们就清楚了。同时，我们对I2C设备的注册定义和注册也就完全清楚了。

 

二、定义和注册I2C设备驱动

步骤1：定义i2c_driver结构体变量。

Linux I2C设备驱动程序对应的结构体是structi2c_driver，定义在include/linux/i2c.h文件中：

 

124/**
125 * struct i2c_driver - represent an I2Cdevice driver
126 * @class: What kind of i2c device weinstantiate (for detect)
127 * @attach_adapter: Callback for busaddition (deprecated)
128 * @probe: Callback for device binding
129 * @remove: Callback for deviceunbinding
130 * @shutdown: Callback for deviceshutdown
131 * @suspend: Callback for device suspend
132 * @resume: Callback for device resume
133 * @alert: Alert callback, for examplefor the SMBus alert protocol
134 * @command: Callback for bus-wide signaling(optional)
135 * @driver: Device driver model driver
136 * @id_table: List of I2C devicessupported by this driver
137 * @detect: Callback for devicedetection
138 * @address_list: The I2C addresses toprobe (for detect)
139 * @clients: List of detected clients wecreated (for i2c-core use only)
140 *
141 * The driver.owner field should be setto the module owner of this driver.
142 * The driver.name field should be setto the name of this driver.
143 *
144 * For automatic device detection, both @detectand @address_list must
145 * be defined. @class should also beset, otherwise only devices forced
146 * with module parameters will becreated. The detect function must
147 * fill at least the name field of thei2c_board_info structure it is
148 * handed upon successful detection, andpossibly also the flags field.
149 *
150 * If @detect is missing, the driverwill still work fine for enumerated
151 * devices. Detected devices simplywon't be supported. This is expected
152 * for the many I2C/SMBus devices whichcan't be detected reliably, and
153 * the ones which can always beenumerated in practice.
154 *
155 * The i2c_client structure which ishanded to the @detect callback is
156 * not a real i2c_client. It isinitialized just enough so that you can
157 * call i2c_smbus_read_byte_data andfriends on it. Don't do anything
158 * else with it. In particular, callingdev_dbg and friends on it is
159 * not allowed.
160 */
161struct i2c_driver {
162   unsigned int class;
163
164   /* Notifies the driver that a new bus has appeared. You should avoid
165    * using this, it will be removed in a near future.
166    */
167   int (*attach_adapter)(struct i2c_adapter *) __deprecated;
168
169   /* Standard driver model interfaces */
170   int (*probe)(struct i2c_client *, const struct i2c_device_id *);
171   int (*remove)(struct i2c_client *);
172
173   /* driver model interfaces that don't relate to enumeration  */
174   void (*shutdown)(struct i2c_client *);
175   int (*suspend)(struct i2c_client *, pm_message_t mesg);
176   int (*resume)(struct i2c_client *);
177
178   /* Alert callback, for example for the SMBus alert protocol.
179    * The format and meaning of the data value depends on the protocol.
180    * For the SMBus alert protocol, there is a single bit of data passed
181    * as the alert response's low bit ("event flag").
182    */
183   void (*alert)(struct i2c_client *, unsigned int data);
184
185   /* a ioctl like command that can be used to perform specific functions
186    * with the device.
187    */
188   int (*command)(struct i2c_client *client, unsigned int cmd, void *arg);
189
190   struct device_driver driver;
191   const struct i2c_device_id *id_table;
192
193   /* Device detection callback for automatic device creation */
194   int (*detect)(struct i2c_client *, struct i2c_board_info *);
195   const unsigned short *address_list;
196   struct list_head clients;
197};

 

注意注释中的说明，driver.name和driver.owner必须初始化。

id_table成员变量是i2c_device_id结构体指针，它用来保存该i2c_driver支持的I2C设备列表。

struct i2c_device_id定义在include/linux/mod_devicetable.h文件中，其内容如下：

 

419struct i2c_device_id {
420   char name[I2C_NAME_SIZE];
421   kernel_ulong_t driver_data; /* Data private to the driver */
422};

 

对于Mini2440的I2C设备at24c08 EEPROM，其对应的i2c_driver结构体变量实现在drivers/misc/eeprom/at24.c文件中：

 

677static struct i2c_driver at24_driver = {
678   .driver = {
679       .name = "at24",
680       .owner = THIS_MODULE,
681   },
682   .probe = at24_probe,
683   .remove = at24_remove,
684   .id_table = at24_ids,
685};

 

678-681行，初始化了要求必须初始化的i2c_driver.driver.name和i2c_driver.driver.owner。

682行，指定i2c_driver.probe函数为at24_probe。

683行，指定i2c_driver.remove函数为at24_remove。

684行，指定i2c_driver.id_table为at24_ids。

at24_ids定义在drivers/misc/eeprom/at24.c文件中，其内容如下：

 

99#define AT24_SIZE_BYTELEN 5
100#define AT24_SIZE_FLAGS 8
101
102#define AT24_BITMASK(x) (BIT(x) - 1)
103
104/* create non-zero magic value for giveneeprom parameters */
105#define AT24_DEVICE_MAGIC(_len,_flags)         \
106   ((1 << AT24_SIZE_FLAGS | (_flags))      \
107       << AT24_SIZE_BYTELEN | ilog2(_len))
108
109static const struct i2c_device_idat24_ids[] = {
110   /* needs 8 addresses as A0-A2 are ignored */
111   { "24c00", AT24_DEVICE_MAGIC(128 / 8, AT24_FLAG_TAKE8ADDR) },
112   /* old variants can't be handled with this generic entry! */
113   { "24c01", AT24_DEVICE_MAGIC(1024 / 8, 0) },
114   { "24c02", AT24_DEVICE_MAGIC(2048 / 8, 0) },
115   /* spd is a 24c02 in memory DIMMs */
116   { "spd", AT24_DEVICE_MAGIC(2048 / 8,
117       AT24_FLAG_READONLY | AT24_FLAG_IRUGO) },
118   { "24c04", AT24_DEVICE_MAGIC(4096 / 8, 0) },
119   /* 24rf08 quirk is handled at i2c-core */
120   { "24c08", AT24_DEVICE_MAGIC(8192 / 8, 0) },
121   { "24c16", AT24_DEVICE_MAGIC(16384 / 8, 0) },
122   { "24c32", AT24_DEVICE_MAGIC(32768 / 8, AT24_FLAG_ADDR16) },
123   { "24c64", AT24_DEVICE_MAGIC(65536 / 8, AT24_FLAG_ADDR16) },
124   { "24c128", AT24_DEVICE_MAGIC(131072 / 8, AT24_FLAG_ADDR16) },
125   { "24c256", AT24_DEVICE_MAGIC(262144 / 8, AT24_FLAG_ADDR16) },
126   { "24c512", AT24_DEVICE_MAGIC(524288 / 8, AT24_FLAG_ADDR16) },
127   { "24c1024", AT24_DEVICE_MAGIC(1048576 / 8, AT24_FLAG_ADDR16)},
128   { "at24", 0 },
129   { /* END OF LIST */ }
130};

 

可以看到，at24_driver支持很多设备，其中包括Mini2440使用的24c08 EEPROM。

 

步骤2：调用i2c_add_driver注册i2c_driver结构体变量。

对于Mini2440的I2C设备at24c08 EEPROM，这一步工作是在drivers/misc/eeprom/at24.c文件中的at24_init函数中完成的：

 

687static int __init at24_init(void)
688{
689   if (!io_limit) {
690       pr_err("at24: io_limit must not be 0!\n");
691       return -EINVAL;
692   }
693
694   io_limit = rounddown_pow_of_two(io_limit);
695   return i2c_add_driver(&at24_driver);
696}

 

695行，调用i2c_add_driver注册上面定义的at24_driver。

i2c_add_driver是一个宏，定义在include/linux/i2c.h文件中：

497/* use a define to avoid include chaining to get THIS_MODULE */
498#define i2c_add_driver(driver) \
499    i2c_register_driver(THIS_MODULE, driver)

i2c_register_driver函数定义在drivers/i2c/i2c-core.c文件中，其内容如下：

1307/*
1308 * An i2c_driver is used with one or more i2c_client (device) nodes to access
1309 * i2c slave chips, on a bus instance associated with some i2c_adapter.
1310 */
1311
1312int i2c_register_driver(struct module *owner, struct i2c_driver *driver)
1313{
1314    int res;
1315
1316    /* Can't register until after driver model init */
1317    if (unlikely(WARN_ON(!i2c_bus_type.p)))
1318        return -EAGAIN;
1319
1320    /* add the driver to the list of i2c drivers in the driver core */
1321    driver->driver.owner = owner;
1322    driver->driver.bus = &i2c_bus_type;
1323
1324    /* When registration returns, the driver core
1325     * will have called probe() for all matching-but-unbound devices.
1326     */
1327    res = driver_register(&driver->driver);
1328    if (res)
1329        return res;
1330
1331    /* Drivers should switch to dev_pm_ops instead. */
1332    if (driver->suspend)
1333        pr_warn("i2c-core: driver [%s] using legacy suspend method\n",
1334            driver->driver.name);
1335    if (driver->resume)
1336        pr_warn("i2c-core: driver [%s] using legacy resume method\n",
1337            driver->driver.name);
1338
1339    pr_debug("i2c-core: driver [%s] registered\n", driver->driver.name);
1340
1341    INIT_LIST_HEAD(&driver->clients);
1342    /* Walk the adapters that are already present */
1343    i2c_for_each_dev(driver, __process_new_driver);
1344
1345    return 0;
1346}

1327行，调用driver_register注册i2c_driver.driver。参考《 Linux设备模型分析之device_driver（基于3.10.1内核）》对Linux设备模型的分析，在driver_register执行过程中，如果I2C总线上找到了与该驱动匹配的I2C设备，则i2c_driver.probe函数会被调用执行。

1343行，调用i2c_for_each_dev遍历所有已存在的i2c_adapter。该函数定义在drivers/i2c/i2c-core.c文件中，其内容如下：

1288int i2c_for_each_dev(void *data, int (*fn)(struct device *, void *))
1289{
1290    int res;
1291
1292    mutex_lock(&core_lock);
1293    res = bus_for_each_dev(&i2c_bus_type, NULL, data, fn);
1294    mutex_unlock(&core_lock);
1295
1296    return res;
1297}

1293行，调用bus_for_each_dev，这个函数定义在drivers/base/bus.c文件中，其内容如下：

 

286intbus_for_each_dev(struct bus_type *bus, struct device *start,
 287            void *data, int (*fn)(struct device *, void *))
 288{
 289   struct klist_iter i;
 290   struct device *dev;
 291   int error = 0;
 292
 293   if (!bus || !bus->p)
 294       return -EINVAL;
 295
 296   klist_iter_init_node(&bus->p->klist_devices, &i,
 297                 (start ?&start->p->knode_bus : NULL));
 298   while ((dev = next_device(&i)) && !error)
 299       error = fn(dev, data);
 300   klist_iter_exit(&i);
 301   return error;
 302}

 

我们在《 Linux设备模型分析之device_driver（基于3.10.1内核）》一文中已经分析过这个函数。这里，传递过来的data参数是要注册的i2c_driver，fn参数是__process_new_driver函数，所以我们来看__process_new_driver函数，该函数定义在drivers/i2c/i2c-core.c文件中，其内容如下：

 

1300static int __process_new_driver(structdevice *dev, void *data)
1301{
1302   if (dev->type != &i2c_adapter_type)
1303       return 0;
1304   return i2c_do_add_adapter(data, to_i2c_adapter(dev));
1305}

 

i2c_do_add_adapter函数定义在drivers/i2c/i2c-core.c文件中，其内容如下：

 

957static int i2c_do_add_adapter(structi2c_driver *driver,
 958                  struct i2c_adapter *adap)
 959{
 960   /* Detect supported devices on that bus, and instantiate them */
 961   i2c_detect(adap, driver);
 962
 963   /* Let legacy drivers scan this bus for matching devices */
 964   if (driver->attach_adapter) {
 965       dev_warn(&adap->dev, "%s: attach_adapter method isdeprecated\n",
 966            driver->driver.name);
 967       dev_warn(&adap->dev, "Please use another way to instantiate"
 968            "your i2c_client\n");
 969       /* We ignore the return code; if it fails, too bad */
 970       driver->attach_adapter(adap);
 971    }
 972   return 0;
 973}

 

这个函数我们在分析i2c_adapter的注册过程时已经分析过了，它主要完成i2c_driver与i2c_adapter上的i2c设备的匹配工作，如果匹配成功，初始化并注册对应的i2c_client。

至此，i2c_driver的注册过程我们就清楚了。

 

步骤3：实现i2c_driver中要示实现的函数

对于Mini2440的I2C设备at24c08 EEPROM，at24_driver要求实现的是i2c_driver.probe和i2c_driver.remove函数。