检查非正常断开的tcp连接
Tcp是面向连接的,在实际应用中通常都需要检测连接是否还可用.如果不可用,可分为:
a. 连接的对端正常关闭.
b. 连接的对端非正常关闭,这包括对端设备掉电,程序崩溃,网络被中断等.这种情况是不能也无法通知对端的,所以连接会一直存在,浪费国家的资源.
tcp协议栈有个keepalive的属性,可以主动探测socket是否可用,不过这个属性的默认值很大.
Linux方法：
全局设置可更改/etc/sysctl.conf,加上:
net.ipv4.tcp_keepalive_intvl = 20
net.ipv4.tcp_keepalive_probes = 3
net.ipv4.tcp_keepalive_time = 60
在程序中设置如下:
int keepAlive = 1; // 开启keepalive属性
int keepIdle = 60; // 如该连接在60秒内没有任何数据往来,则进行探测
int keepInterval = 5; // 探测时发包的时间间隔为5 秒
int keepCount = 3; // 探测尝试的次数.如果第1次探测包就收到响应了,则后2次的不再发.
setsockopt(rs, SOL_SOCKET, SO_KEEPALIVE, (void *)&keepAlive, sizeof(keepAlive));
setsockopt(rs, SOL_TCP, TCP_KEEPIDLE, (void*)&keepIdle, sizeof(keepIdle));
setsockopt(rs, SOL_TCP, TCP_KEEPINTVL, (void *)&keepInterval, sizeof(keepInterval));
setsockopt(rs, SOL_TCP, TCP_KEEPCNT, (void *)&keepCount, sizeof(keepCount));
Windows方法：
//定义结构及宏
struct TCP_KEEPALIVE {
u_longonoff;
u_longkeepalivetime;
u_longkeepaliveinterval;
} ;
#define SIO_KEEPALIVE_VALS _WSAIOW(IOC_VENDOR,4)
//KeepAlive实现
TCP_KEEPALIVE inKeepAlive = {0}; //输入参数
unsigned long ulInLen = sizeof(TCP_KEEPALIVE);
TCP_KEEPALIVE outKeepAlive = {0}; //输出参数
unsigned long ulOutLen = sizeof(TCP_KEEPALIVE);
unsigned long ulBytesReturn = 0;
//设置socket的keep alive为5秒，并且发送次数为3次
inKeepAlive.onoff = 1;
inKeepAlive.keepaliveinterval = 5000; //两次KeepAlive探测间的时间间隔
inKeepAlive.keepalivetime = 5000; //开始首次KeepAlive探测前的TCP空闭时间
if (WSAIoctl((unsigned int)s, SIO_KEEPALIVE_VALS,
(LPVOID)&inKeepAlive, ulInLen,
(LPVOID)&outKeepAlive, ulOutLen,
&ulBytesReturn, NULL, NULL) == SOCKET_ERROR)
{
}
在程序中表现为,当tcp检测到对端socket不再可用时(不能发出探测包,或探测包没有收到ACK的响应包),select会返回socket可读,并且在recv时返回-1,同时置上errno为ETIMEDOUT
补充一个查看tcp连接状态的例子：
int tcp_state(int tcp_fd)
{
struct tcp_info info;
int optlen = sizeof(struct tcp_info);
if (getsockopt (tcp_fd, IPPROTO_TCP, TCP_INFO, &info, (socklen_t *)&optlen) < 0) {
printf ("getsockopt() TCP_INFO error/n"); exit (0);
}
printf ("%d/n",info.tcpi_state);
if (info.tcpi_state == TCP_ESTABLISHED) return 0; /* ESTABLISHED */
else return -1;
}